Bandpass Signal Sampling and Coherent Detection

Coherent detectors in radar and communications receivers are generally implemented in the form of two parallel baseband channels which form in-phase (I) and quadrature (Q) components of a received RF/IF signal. Phase errors of several degrees due to imperfect matching of these separate channels limit the performance achievable from signal processors such as moving target indicators (MTI), coherent integrators, Doppler filters, antenna array processors, and coherent sidelobe cancellers. Thus methods in which a single analog to digital (A/D) converter samples and digitizes the IF signal directly, eliminating the need for IF to baseband conversion, have been of recent interest and are the subject of this paper. To obtain accurate coherent detection from IF samples taken near the Nyquist rate requires interpolation based upon a number of stored samples. An algorithm derived from sampling theory is defined and used to demonstrate accurate reconstruction of the original IF signal from digitized samples. In-phase and quadrature components of the signal are shown to be available from processed samples with demonstrated phase errors less than 0.2°.     

基于FPGA的FIR滤波器设计与实现

本文根据激光陀螺仪信号的解调原理,提出了一种利用数字信号处理技术并采用FPGA实现的解调方法。分析了FIR滤波器的工作原理,根据激光陀螺仪对滤波器的要求,给出了由FPGA设计实现FIR滤波器的基本原理,并利用IP核实现了FIR滤波器,满足了激光陀螺仪的需求。通过在国产激光陀螺仪上的应用,验证了方案的正确性。通过对激光陀螺仪脉冲计数的高速采样并利用数字滤波器处理,可以有效的消除抖动引起的信号噪声,得到所需要的惯性信息。采用FPGA设计实现,可以提高运算速度,并且可以缩短数据采样的延时。     

低通滤波器的阶跃响应及其对动态校准的影响

动态测试系统在利用阶跃信号进行动态校准时,系统中的低通滤波器环节所产生的衰减振荡可能会误导测试人员,特别是对于带传压管道的动态压力测试系统。仿真与测试结果表明,各种模拟低通滤波器和IIR数字低通滤波器的阶跃响应都会出现一定的衰减振荡。针对带低通滤波器的系统以及其他系统的阶跃激励校准,通过对简单FFT频响分析方法、矩形单脉冲法、冲激响应法三种方法的比较,发现矩形单脉冲法能更正确地对阶跃校准数据进行频响分析。     

A Simple Method for Sampling In-Phase and Quadrature Components

We present a method of developing in-phase and quadrature samples of a band-limited RF waveform. The problem of matching gain and phase response differences between the two components is avoided by a combination of mixing to an IF frequency, sampling and digitizing, and digital filtering. The novelty of the method is in the design of the digital filter, which is realized as a pair of 900 phase splitting networks with several symmetries which are exploited to save computation.     

基于自适应FIR算法的交流伺服系统前馈控制

永磁同步电机(PMSM)交流伺服控制系统中由于电子器件的开关引起相电流非正弦变化,经坐标变换得到的交直轴电流含有谐波成分,引起电流环振荡及电磁转矩脉动。在分析相电流与交直轴电流高次谐波关系,以及交直轴电流高次谐波对电磁转矩影响的基础上,提出了一种基于自适应FIR滤波器的交流伺服系统前馈控制策略,并在该方法的基础上提出了变步长因子算法,根据误差值改变步长因子,在提高滤波器收敛速度的同时减小超调。该算法与传统的一阶低通滤波器相比,相位不滞后,灵敏度更高,且系统稳定。改进后的控制策略有效地降低交直轴电流谐波,抑制电流环振荡及电磁转矩脉动,提高PMSM交流伺服控制系统稳定性及动态响应。通过仿真与试验证明了该方法的可行性。     

应用于航空变频电源系统的新型串沥混合有源滤波器

 目前变频交流(AC)电源系统开始逐渐应用到新型多电飞机(MEA)中,传统有源滤波器无法满足宽输入频率变化要求,为此需要设计一种适合于宽变频航空电源系统的有源滤波器。本文研究了一种应用于航空变频电源系统的新型串联混合有源滤波器(SHAPF),该有源滤波器直接根据基波电流进行补偿,针对各种频率输入均能起到较好的抑制谐波作用。讨论了这种新型SHAPF的变频谐波抑制原理,给出了该滤波器的控制系统详细设计过程,包括基于双数字信号处理器（DSP）的控制平台设计和逐点动态检测基波电流的算法设计,最后进行了样机实验,对比了加入滤波器前后系统输入电流实验波形和谐波分析,加入滤波器后系统输入电流总谐波失真度（THD）由174.00%变化至4.80%,滤波效果良好;在360 Hz,400 Hz和720 Hz不同输入频率进行了滤波实验,验证系统在宽变频输入条件下均具有良好控制性能,满足航空变频输入时输入功率因数校正要求。     

正交调制实现窄带带通数字滤波器

为了提高滤波器性能并简化设计,采用正交调制等效结构实现了带通滤波,使一组中心频率不同,而其余指标都相同的窄带带通数字滤波器设计简化为一个窄带低通数字滤波器设计.对窄带低通数字滤波器设计,又采用了多抽样率多级实现技术,提高了运算效率,节省了存储空间.该设计已在TMS320C3X系列DSP芯片上调试通过,并运用于铁路电气化区段机车信号译码.     

Optimum gain control for A/D conversion using digitized I/Q data inquadrature sampling

Calculation of optimum gain for minimum distortion due to A/D (analog-to-digital) conversion requires the estimation of the input signal strength. To use a common AGC (automatic gain control) for both the I/Q (in-phase and quadrature) signals, it is efficient to estimate the input signal strength using the quantized A/D output from both channels. Assuming a Gaussian input, the relationship between σ of the input of the A/D converter and E(|x|+|y|) and E(max(|x|,|y|)+1/2 min (|x|,|y|)) for t quantized I/Q output x and y is derived. Numerical results obtained using the derived expression and the statistical data obtained through simulation show excellent agreement. It is concluded that, because of its simplicity, the cubic equation obtained by fitting the numerical results should be useful     

Time jitter analysis for quadrature sampling

Time jitter in the quadrature sampling processes is modeled and the performance of an adaptive cancellation system in the presence of such time jitter is analyzed. It is shown that the decorrelation due to time jitter depends on the magnitude of the jitter, the sampling scheme used, the bandwidth of the signal and the intermediate frequency (IF) preceding the analog-to-digital (A/D) conversion stages. The performance of a sidelobe cancellation system in the presence of time jitter, for several sampling approaches, is evaluated numerically as well as simulated. The results show that the direct quadrature sampling scheme with a lower IF provides superior performance for an adaptive cancellation system     

谐振式光子晶体光纤陀螺信号检测及处理技术研究

谐振式光子晶体光纤陀螺是一种具有小型化、高精度等潜在技术优势的新型光纤陀螺,是国内外惯性器件研究的一个重要发展方向。针对谐振式光子晶体光纤陀螺的结构和信号检测原理进行了详细的叙述,确定了基于FPGA的陀螺信号检测总体方案,陀螺信号处理及控制模块主要由频差信号解调、复合拍频检测、闭环反馈控制、数据编码输出以及调制信号模块组成;随后重点介绍了窄线宽半导体激光器的驱动控制方案,在调制解调及频率偏差检测方案上采用数字相敏检波器实现频率偏差检测,在谐振频率闭环跟踪锁定方案上采用数字PI控制器实现环路光频率控制;最后进行了谐振式光子晶体光纤陀螺实验测试系统搭建,以及谐振曲线测试和谐振频率闭环锁定测试。     

一种基于EPLL技术的自适应正交解调技术研究

针对过零检测实现的全数字锁相环不仅锁相速度慢, 而且过零点的扰动会 直接影响锁相精度以及适合模拟电路实现的相干解调技术,在数字电路中实现则需要设 计高阶数字低通滤波器,将占用大量数字电路资源并且会显著增加系统功耗等问题,在 设计一种新型全数字锁相环(All-digital Enhanced Phase-lock Loop,EPLL)的基础上,结合自 适应正交解调技术,提出了一种基于EPLL 技术的自适应正交解调技术方案,并对该方 案进行了研究与仿真。仿真得到了满意的结果,验证了基于EPLL 技术的自适应正交解 调技术方案的可行性,并研究验证了算法的参数变化对其性能的影响,为今后算法在数 字系统中的实现以及其在各领域的应用研究奠定了坚实的基础。     

Coherent Square Wave Demodulation of Ideal Limiter Output

An ideal limiter may be used to single-bit quantize a noisy sinusoidal signal. This digitization is particularly economical if the signal is to be recorded. lt might then be desired to obtain phase coherence with the limited input signal. A single-bit digital phase-locked loop. utilizing a square wave reference, could be used for this purpose. The effects of coherent square wave demodulation on the signal-to-noise ratio and the (signal-to-noise spectral density) ratio are discussed. The latter result is directly applicable to the performance of the digital phase-locked loop.     

Evaluation of Image Response Signal Power Resulting from I-Q Channel Imbalance

A simple relationship is obtained that gives the ratio of the image to the desired signal in terms of the amplitude and phase imbalance between the I and Q channels in a quadrature transmission and signal reconstruction processor.     

Full control of a PWM DC-AC converter for AC voltage regulation

The design and implement action of a DSP-based fully digital-controlled single-phase pulsewidth modulated (PWM) dc-ac converter for ac voltage regulation is described. The proposed multiloop digital controller (MDC) consists of a current controller, a voltage controller, and a feedforward controller. This MDC was realized using a single-chip digital signal processor (DSP). The PWM gating signals are determined at every sampling instant by the proposed multiloop digital control scheme using a set of detected feedback signals. A software current control; scheme has been developed to achieve fast current control of the PWM inverter and decouple the inductor of the output filter. Experimental results have been given to verify the proposed digital control scheme. The constructed DSP-based PWM dc-ac converter system can achieve fast dynamic response and with low total harmonic distortion (THD) for rectifier type of loads     

全数字宽带接收机的并行结构

介绍了一种FFT并行结构的全数字宽带接收机，接收机中包括载波恢复，定时恢复和匹配滤波器三个主要功能部分。其特点是信号处理速率比输入Nyquist采样速率低得多，而且其中的匹配滤波器和定时校正恢复可以在频域上有效地实现，这种结构特别适合于卫星通信中每秒几百兆比特速率的高速数据传输应用。     

GPS多径信号的自适应滤波估计方法

 研究全球定位系统(GPS)多径信号估计的问题。通过分析自适应滤波器的原理,建立了数字中频信号处理的数学模型,提出一种用自适应滤波实现GPS多径幅度、码相位和载波相位估计的方法。该方法采用不同延迟的伪随机序列对信号进行解扩、解调和累加,得到了作为期望信号的系列自适应滤波相关值。对该方法与其他3种方法进行了理论上的分析比较,得出本方法具有信噪比高、自适应滤波性能好、带有码相位信息和不存在载波模糊度问题等优点。根据各种滤波器算法的特点和本应用的需求,给出了选用递归最小二乘算法实现的方法。通过计算机仿真,验证了提出的方法能够在14 dB的信噪比下,以1个采样间隔的时间延迟分辨率和0.005周的载波相位估计精度估计出GPS L1的多径信号。     

False alarm analysis of the envelope detection GO-CFAR processor

The greatest of constant false alarm rate processor (GO CFAR) is a useful architecture for adaptively setting a radar detection threshold in the presence of clutter edges. The GO CFAR input is often the envelope detected in-phase (I) and quadrature (Q) channels of the baseband signal (x_e=√(I²+Q²)). This envelope detection can also be approximated using x=a max{|I|,|Q|}+b min{|I|,|Q|} which requires less complex hardware (a and b are simple multiplying coefficients). The envelope GO CFAR processor and several envelope approximation GO CFAR processors are compared in terms of the probability of false alarm (PFA) performance. Closed-form expressions which describe the PFA performance are given and their accuracy evaluated. It is shown that for all cases, the PFA is proportional to the number of reference cells n for small threshold multiplier T and inversely proportional to n for large T. A region of intersection occurs where the PFA is the same for two different values of n. For example, at T'=1.68 in the |I|+|Q| GO CFAR (a=1, b=1) the PFA for n=1 is equal to the optimal n=∞ fixed-threshold PFA (PFA=0.112)     

Multipath-adaptive GPS/INS receiver

Multipath interference is one of the contributing sources of errors in precise global positioning system (GPS) position determination. This paper identifies key parameters of a multipath signal, focusing on estimating them accurately in order to mitigate multipath effects. Multiple model adaptive estimation (MMAE) techniques are applied to an inertial navigation system (INS)-coupled GPS receiver, based on a federated (distributed) Kalman filter design, to estimate the desired multipath parameters. The system configuration is one in which a GPS receiver and an INS are integrated together at the level of the in-phase and quadrature phase (I and Q) signals, rather than at the level of pseudo-range signals or navigation solutions. The system model of the MMAE is presented and the elemental Kalman filter design is examined. Different parameter search spaces are examined for accurate multipath parameter identification. The resulting GPS/INS receiver designs are validated through computer simulation of a user receiving signals from GPS satellites with multipath signal interference present The designed adaptive receiver provides pseudo-range estimates that are corrected for the effects of multipath interference, resulting in an integrated system that performs well with or without multipath interference present.     

An anti-image interference quadrature IF architecture for satellite receivers

Since Global Navigation Satellite System（GNSS） signals span a wide range of frequency, wireless signals coming from other communication systems may be aliased and appear as image interference. In quadrature intermediate frequency（IF） receivers, image aliasing due to in-phase and quadrature（I/Q） channel mismatches is always a big problem. I/Q mismatches occur because of gain and phase imbalances between quadrature mixers and capacitor mismatches in analog-to-digital converters（ADC）. As a result, the dynamic range and performance of a receiver are severely degraded. In this paper, several popular receiver architectures are summarized and the image aliasing problem is investigated in detail. Based on this analysis, a low-IF architecture is proposed for a single-chip solution and a novel and feasible anti-image algorithm is investigated. With this anti-image digital processing, the image reject ratio（IRR） can reach approximately above50 dB, which relaxes image rejection specific in front-end circuit designs and allows cheap and highly flexible analog front-end solutions. Simulation and experimental data show that the antiimage algorithm can work effectively, robustly, and steadily.     

The effect of I,Q mismatch errors on adaptive cancellation

The effects of in-phase (I) and quadrature-phase (Q) amplitude errors and low-pass-filter (LPF) errors on adaptive cancellers are investigated. I,Q errors occur because of errors in the synthesis process of the mixers and LPFs designed to be identical for each input channel. These I,Q errors among the channels result in cancellation degradation. Tapped delay line transversal filters have been proposed as a way to compensate for these errors and thus improve cancellation performance. However, it is shown that if there is any LPF mismatch, then transversal filtering has a small effect on improving canceler performance. The use of individual I,Q adaptive transversal filter weighting is suggested as a means of completely eliminating the phase amplitude errors, and making the canceler performance responsive to transversal filter compensation