共查询到20条相似文献,搜索用时 109 毫秒
1.
新一代运载火箭增压技术研究 总被引:6,自引:0,他引:6
随着新一代运载火箭研制的开展,新型120t级高压补燃液氧煤油发动机将得到广泛的使用,该发动机采用的推进剂贮箱增压系统设计被列为新一代运载火箭研制的重大关键技术之一。在对国内外主要液体运载火箭增压方案进行分析的基础上对120t级液氧煤油发动机的贮箱增压系统进行了研究,提出了液氧贮箱采用压力传感器与电磁阀组合的常温氦气加温增压,煤油贮箱采用压力传感器与电磁阀组合的常温氦气增压方案,并针对液氧贮箱采用常温氦气加温增压的方案开展了理论分析和全尺寸系统级试验研究。理论分析和试验结果表明,该增压方案可行。 相似文献
2.
运载火箭低温推进剂热管理技术及应用进展分析 总被引:1,自引:0,他引:1
运载火箭低温推进剂与外界环境的传热是造成汽化的主要原因。为长期贮存和使用低温推进剂,必须采用综合的热管理技术。首先介绍国内外提出的被动热防护技术和主动制冷技术。前者的主要目的是降低贮箱与外界环境的热量交换强度;后者是通过对贮箱内的热量进行转移,以实现低温推进剂的无损贮存,但只适合已具有良好被动热防护的贮箱。其次,对国外典型低温推进剂实验应用系统进行分析,并初步提出多功能液氢实验平台方案设想,方案中通过CZ-3A号搭载多功能液氢实验平台用于验证空间环境下低温推进剂的综合应用技术。通过对低温推进剂热管理技术的调研和论证,为我国低温推进剂在空间环境下的长期在轨使用提供技术参考。 相似文献
3.
4.
5.
6.
7.
8.
低温液体推进剂增压分析与计算 总被引:1,自引:0,他引:1
运载火箭低温推进剂贮箱的增压问题极为复杂,其传热问题的研究分析又受到很大的限制.为此,根据我国上面级低温液体推进剂火箭的要求及其具体条件,推导和制定了整个飞行过程的贮箱增压计算方法、主动段—滑行段—主动段的计算公式和必需的初始数据.计算结果与国外同类试验结果规律相一致,与某型号低温推进剂火箭飞行结果相接近,证明该计算方法是可行的. 相似文献
9.
运载火箭在飞行过程中需要进行姿态调整以满足入轨要求,贮箱内推进剂在外界干扰力的作用下将发生晃动,由此引入了诸如气液接触面积、蒸发、冷凝过程及推进剂流动变化等不确定影响因素。实际飞行过程尤其是进入滑行段的初始推进剂晃动对贮箱内气枕压力及推进剂流动行为具有重要影响。在调研国内外运载火箭末级飞行过程中低温贮箱压力及推进剂流动特性的基础上,建立仿真模型,采用流体体积函数方法(VOF)分析滑行段推进剂流动特性变化对贮箱气枕压力的影响。 相似文献
10.
《火箭推进》2018,(5)
在液氧/煤油火箭发动机地面试验中,为得到液氧贮箱放气系统放气流量与放气阀门动作的响应特性,从而控制箱压的下降速率,验证液氧煤油发动机在低入口压力条件下的工作适应性,对液氧贮箱放气系统的动态特性进行了研究。建立了液氧贮箱二维计算模型,结合试验数据,对低温贮箱内气枕空间的非稳态换热过程进行研究,确定放出气体温度以及相应状态。应用CFD的动网格技术,建立二维计算模型,对放气系统阀门的开关动态特性与过流流量特性进行综合分析,获得了不同通径放气管路的放气流量与箱压的计算关联式,基于理想气体状态方程,完善了箱压计算理论模型。应用该模型量化分析箱压下降速率,为计算箱压控制的准确时间节点提供了操作参考。 相似文献
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
13.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
14.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献
15.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
16.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
17.
18.
19.