某型发动机防冰系统的性能改进

分析了某型发动机防冰性能上的缺陷,提出了改进方案,对于设计改进该型发动机的防冰系统,有很好的参考价值。     

改进的小波均匀化方法求解小周期系数抛物型方程

对传统的小波数值均匀化方法通过加入逐层修正的步骤进行了改进,并将改进后的方法用于求解具有小周期系数的抛物型方程。数值算例结果表明：在保持较高计算效率的同时,改进后的方法比改进前方法在精度方面有明显的提高。因此,改进后方法是小周期系数抛物型方程的一种高效率、高精度的数值求解方法。     

两相流环缝塞式喷管设计方法

 在常滞后两相流假设下,提出改进的Angelino理想型面法和改进的“二次曲线+三次曲线”造型法设计两相流环缝塞式喷管;计算了这两种改进方法设计的塞式喷管性能。算例表明:在两相流条件下与未考虑两相流效应的气相理想方法设计的型面相比,改进的Angelino法设计的型面长度缩短近33%,推力增大约1%;改进的“二次曲线+三次曲线”造型法设计的型面长度减小近6%,性能提高约4%。     

某型机座舱照明系统分析与改进

深入分析了某型机座舱照明"左明右暗"产生原因,进行了改进技术方案论证。根据飞机现状,提出了改进座舱照明效果最优技术方案。     

横Π型梁在风洞应变天平阻力结构上的应用

主要通过对比传统T型梁和横Π型梁,对风洞应变天平的阻力测量梁进行了分析,根据分析结果提出了传统的横Π型阻力测量梁的改进方式,并通过有限元分析软件进行了优化分析,改进后的横Π型阻力测量梁降低了升力对阻力的干扰,并有利于提高天平阻力分量的稳定性。该测量梁结构应用到了某型飞机高速风洞试验测力天平上,天平静态校准结果与理论分析结果吻合,风洞试验时天平状态良好、性能稳定。     

涡扇发动机起动和加速规律的研究及应用

研究了涡扇发动机起动和加速的一般规律及其设计方法;针对某型涡扇发动机存在的起动和加速方面的问题,进行了大量的试验研究和理论分析,提出了改进设计的方案,经验证,采用改进方案,大大提高了该型发动机空中加速性和地面起动性能.     

某型火药点火器意外发火原因分析及排查

针对某型俄制敏感型火药点火器意外发火的情况,对可能造成意外发火的原因进行了详细分析及排查,提出了改进措施及建议。     

AMEsim仿真软件在某型叶片控制机构改进中的应用

通过分析某型叶片控制机构在试验中出现的问题,提出改进方案,并利用AMEsim软件对改进后系统的性能进行了仿真,系统仿真结果与改进后系统的物理试验结果基本相符.     

米格-29家族新成员

文章介绍了米格-29系列战斗机新的发展方向，即计划研制它的改进型以及改进现役的战斗机。改进型包括舰载型战斗机米格-29K、双座陆基型多用途战斗机米格-29M2等；对现役米格-29进行模块化改进成为米格-29SMT并简要介绍了它们改进后的性能特点。     

面对21世纪的改进从“黄蜂”到“超黄蜂”(下)

改进电子设备在美国海军为F／A-18作规划时，E／F型的改进只是个开端。海军在解决了原来机体的缺陷之后，现在急于要搞清F／A—18上电子设备的局限性。为了使成本不致太高，目前的E／F型利用了C／D型中90％的电子设备。到2005年左右，波音公司将把即将完成试验的下一代电子设备装上飞机。新的基本航空电子设备包括正在为C／D型和E／F型两种机型研制的改进项目，有高级寻的前视红外（ATFLIR）吊舱、安装在头盔上的信号系统（JHMCS）和多功能信息分配系统（MIDS）。除此之外，还计划为E／F型作一些单独的改进，从一体化防御性电…     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

GA-Based Model Predictive Control of Semi-Active Landing Gear

Semi-active landing gear can provide good performance of both landing impact and taxi situation, and has the ability for adapting to various ground conditions and operational conditions. A kind of Nonlinear Model Predictive Control algorithm （NMPC） for semi-active landing gears is developed in this paper. The NMPC algorithm uses Genetic Algorithm （GA） as the optimization technique and chooses damping performance of landing gear at touch down to be the optimization object. The valve＇s rate and magnitude limitations are also considered in the controller＇s design. A simulation model is built for the semi-active landing gear＇s damping process at touchdown. Drop tests are carried out on an experimental passive landing gear systerm to validate the parameters of the simulation model. The result of numerical simulation shows that the isolation of impact load at touchdown can be significantly improved compared to other control algorithms. The strongly nonlinear dynamics of semi-active landing gear coupled with control valve＇s rate and magnitude limitations are handled well with the proposed controller.     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。