The design features of the GGS wind and polar spacecraft

The Global Geospace Science (GGS) WIND and POLAR spacecraft employ unique configuration and design features driven by the requirements of the science instruments which they host. The WIND and POLAR spacecraft are cylindrically shaped spinners (WIND 20 rpm, POLAR 10 rpm) approximately 2.4 m in diameter and 1.8 m high. Each spacecraft has a pair of lanyard booms, which hold magnetometers, four radial wire antennas and two spin-axis antennas. While satisfying different mission requirements, both share a common basic design. The WIND laboratory contains 8 instruments, designed to optimize measurements of waves, fields and particle distributions. The POLAR laboratory contains 12 instruments, with a similar design emphasis on waves, fields and particle measurements, as well as on auroral imaging. The main difference between the two spacecraft is a despun platform on POLAR which provides a stable environment for the auroral imager instruments. Both laboratories are designed to be launched on Delta II model 7925 launch vehicle and have total masses of approximately 1150 g (WIND) and 1240 kg (POLAR).     

The Ultra-Low-Energy Isotope Spectrometer (ULEIS) for the ACE spacecraft

The Ultra Low Energy Isotope Spectrometer (ULEIS) on the ACE spacecraft is an ultra high resolution mass spectrometer designed to measure particle composition and energy spectra of elements He-Ni with energies from ∼45 keV nucl−1 to a few MeV nucl−1. ULEIS will investigate particles accelerated in solar energetic particle events, interplanetary shocks, and at the solar wind termination shock. By determining energy spectra, mass composition, and their temporal variations in conjunction with other ACE instruments, ULEIS will greatly improve our knowledge of solar abundances, as well as other reservoirs such as the local interstellar medium. ULEIS is designed to combine the high sensitivity required to measure low particle fluxes, along with the capability to operate in the largest solar particle or interplanetary shock events. In addition to detailed information for individual ions, ULEIS features a wide range of count rates for different ions and energies that will allow accurate determination of particle fluxes and anisotropies over short (∼few minutes) time scales. This revised version was published online in June 2006 with corrections to the Cover Date.     

The Toroidal Imaging Mass-Angle Spectrograph (TIMAS) for the polar mission

The science objectives of the Toroidal Imaging Mass-Angle Spectrograph (TIMAS) are to investigate the transfer of solar wind energy and momentum to the magnetosphere, the interaction between the magnetosphere and the ionosphere, the transport processes that distribute plasma and energy throughout the magnetosphere, and the interactions that occur as plasma of different origins and histories mix and interact. In order to meet these objectives the TIMAS instrument measures virtually the full three-dimensional velocity distribution functions of all major magnetospheric ion species with one-half spin period time resolution. The TIMAS is a first-order double focusing (angle and energy), imaging spectrograph that simultaneously measures all mass per charge components from 1 AMU e^–1 to greater than 32 AMU e^–1 over a nearly 360° by 10° instantaneous field-of-view. Mass per charge is dispersed radially on an annular microchannel plate detector and the azimuthal position on the detector is a map of the instantaneous 360° field of view. With the rotation of the spacecraft, the TIMAS sweeps out very nearly a 4 solid angle image in a half spin period. The energy per charge range from 15 eV e^–1 to 32 keV e^–1 is covered in 28 non-contiguous steps spaced approximately logarithmically with adjacent steps separated by about 30%. Each energy step is sampled for approximately 20 ms;14 step (odd or even) energy sweeps are completed 16 times per spin. In order to handle the large volume of data within the telemetry limitations the distributions are compressed to varying degrees in angle and energy, log-count compressed and then further compressed by a lossless technique. This data processing task is supported by two SA3300 microprocessors. The voltages (up to 5 kV) for the tandem toroidal electrostatic analyzers and preacceleration sections are supplied from fixed high voltage supplies using optically controlled series-shunt regulators.     

Solar power system options for the Radiation and TechnologyDemonstration spacecraft

The Radiation and Technology Demonstration (RTD) Mission has the primary objective of demonstrating high-power (10 kilowatts) electric thruster technologies in Earth orbit. This paper discusses the conceptual design of the RTD spacecraft photovoltaic (PV) power system and mission performance analyses. These power system studies assessed multiple options for PV arrays, battery technologies and bus voltage levels. To quantify performance attributes of these power system options, a dedicated Fortran code was developed to predict power system performance and estimate system mass. The low-thrust mission trajectory was analyzed and important Earth orbital environments were modeled. Baseline power system design options are recommended on the basis of performance, mass and risk/complexity. Important findings from parametric studies are discussed and the resulting impacts to the spacecraft design and cost     

Radioisotope AMTEC power system designs for spacecraft applications

The authors describe and compare small (two-module) and larger (16-module) AMTEC (alkali metal thermal-to-electric converter) radioisotope powered systems and describe the computer model developed to predict their performance. The high efficiency and static conversion process combined with minimized parasitic losses and operating temperatures that allow the use of current materials while still maintaining a competitive radiator area are found to make AMTEC an excellent candidate for enhanced performance space power systems. AMTEC has the capability of reducing mission costs relative to other static conversion systems because of its high efficiency. AMTEC can also reduce cost relative to dynamic systems simply by being less massive (10 to 5000 W level), and its use eliminates the torque and vibration issues of dynamic systems     

The stretched lens array (SLA) [spacecraft solar power]

At IECEC 2001, this team presented a paper on the new stretched lens array (SLA), including its evolution from the successful SCARLET array on the NASA/JPL Deep Space 1 spacecraft. Since that conference, the SLA team has made significant advances in SLA technology, including component-level improvements, array-level optimization, space environment exposure testing, and prototype hardware fabrication and evaluation. This paper describes the evolved version of the SLA, highlighting recent improvements in the lens, solar cell, photovoltaic receiver, rigid panel structure, and complete solar array wing. In addition to excellent durability in the space environment, the near-term SLA will provide outstanding wing-level performance parameters: 180 W/kg specific power; 300 W/m/sup 2/ power density; 300 V operational voltage; 85% savings in cell area (cm/sup 2//W) and cell-related cost ($/W) compared to planar arrays; 9 kW/m/sup 3/ stowed power at launch.     

近地航天器量子导航定位卡尔曼滤波算法研究

针对近地航天器量子导航定位系统,为了进一步提高其定位精度,利用滤波技术将QPS测量值结合航天器的运动模型进行状态量的滤波估计.给出了基于基线干涉原理的量子定位系统观测方程和以二体运动为主的航天器轨道运动模型,在此基础上详细推导了扩展卡尔曼滤波处理过程,并针对该模型进行了仿真.仿真结果表明,基于EKF的量子导航定位精度有明显提高.     

Far ultraviolet imaging from the IMAGE spacecraft. 2. Wideband FUV imaging

The Far Ultraviolet Wideband Imaging Camera (WIC) complements the magnetospheric images taken by the IMAGE satellite instruments with simultaneous global maps of the terrestrial aurora. Thus, a primary requirement of WIC is to image the total intensity of the aurora in wavelength regions most representative of the auroral source and least contaminated by dayglow, have sufficient field of view to cover the entire polar region from spacecraft apogee and have resolution that is sufficient to resolve auroras on a scale of 1 to 2 latitude degrees. The instrument is sensitive in the spectral region from 140–190 nm. The WIC is mounted on the rotating IMAGE spacecraft viewing radially outward and has a field of view of 17° in the direction parallel to the spacecraft spin axis. Its field of view is 30° in the direction perpendicular to the spin axis, although only a 17°×17° image of the Earth is recorded. The optics was an all-reflective, inverted Cassegrain Burch camera using concentric optics with a small convex primary and a large concave secondary mirror. The mirrors were coated by a special multi-layer coating, which has low reflectivity in the visible and near UV region. The detector consists of a MCP-intensified CCD. The MCP is curved to accommodate the focal surface of the concentric optics. The phosphor of the image intensifier is deposited on a concave fiberoptic window, which is then coupled to the CCD with a fiberoptic taper. The camera head operates in a fast frame transfer mode with the CCD being read approximately 30 full frames (512×256 pixel) per second with an exposure time of 0.033 s. The image motion due to the satellite spin is minimal during such a short exposure. Each image is electronically distortion corrected using the look up table scheme. An offset is added to each memory address that is proportional to the image shift due to satellite rotation, and the charge signal is digitally summed in memory. On orbit, approximately 300 frames will be added to produce one WIC image in memory. The advantage of the electronic motion compensation and distortion correction is that it is extremely flexible, permitting several kinds of corrections including motions parallel and perpendicular to the predicted axis of rotation. The instrument was calibrated by applying ultraviolet light through a vacuum monochromator and measuring the absolute responsivity of the instrument. To obtain the data for the distortion look up table, the camera was turned through various angles and the input angles corresponding to a pixel matrix were recorded. It was found that the spectral response peaked at 150 nm and fell off in either direction. The equivalent aperture of the camera, including mirror reflectivities and effective photocathode quantum efficiency, is about 0.04 cm². Thus, a 100 Rayleigh aurora is expected to produce 23 equivalent counts per pixel per 10 s exposure at the peak of instrument response.     

An approach to forming the design performance of the attitude control system for small spacecraft

The elements for various types of attitude control systems used in a number of small spacecraft are considered. An approach for assessment of such system effectiveness based on design requirements for spacecraft purpose and restriction in accuracy, mass and energy is proposed.     

Event-triggered and consensus-based attitude tracking alignment for discrete-time multiple spacecraft system exploiting interference

This paper presents a discrete-time attitude control strategy with equi-global practical stabilizability for aligning the attitude of multiple spacecraft to a predesigned configuration according to a time-variant reference. By utilizing the interference of the wireless channel, the communication scheme designed in this paper can save communication resources, amount of computation, and energy proportionally to the number of spacecraft. The exact discrete-time model and approximate discrete-time model of the consensus-based spacecraft tracking system are given. Then the framework for the design of an event-triggered control scheme for the exact discrete-time system via its approximate models is developed, which avoids the periodic actuation, and Zeno behavior is proved to be excluded. Furthermore, the control scheme can handle the presence of the unknown fading channel. Finally, simulation results are presented to demonstrate the effectiveness of the control strategy.     

SWE,a comprehensive plasma instrument for the WIND spacecraft

The Solar Wind Experiment (SWE) on the WIND spacecraft is a comprehensive, integrated set of sensors which is designed to investigate outstanding problems in solar wind physics. It consists of two Faraday cup (FC) sensors; a vector electron and ion spectrometer (VEIS); a strahl sensor, which is especially configured to study the electron strahl close to the magnetic field direction; and an on-board calibration system. The energy/charge range of the Faraday cups is 150 V to 8 kV, and that of the VEIS is 7 V to 24.8 kV. The time resolution depends on the operational mode used, but can be of the order of a few seconds for 3-D measurements. Key parameters which broadly characterize the solar wind positive ion velocity distribution function will be made available rapidly from the GGS Central Data Handling Facility.     

A three-dimensional plasma and energetic particle investigation for the wind spacecraft

This instrument is designed to make measurements of the full three-dimensional distribution of suprathermal electrons and ions from solar wind plasma to low energy cosmic rays, with high sensitivity, wide dynamic range, good energy and angular resolution, and high time resolution. The primary scientific goals are to explore the suprathermal particle population between the solar wind and low energy cosmic rays, to study particle accleration and transport and wave-particle interactions, and to monitor particle input to and output from the Earth's magnetosphere.Three arrays, each consisting of a pair of double-ended semi-conductor telescopes each with two or three closely sandwiched passivated ion implanted silicon detectors, measure electrons and ions above 20 keV. One side of each telescope is covered with a thin foil which absorbs ions below 400 keV, while on the other side the incoming <400 keV electrons are swept away by a magnet so electrons and ions are cleanly separated. Higher energy electrons (up to 1 MeV) and ions (up to 11 MeV) are identified by the two double-ended telescopes which have a third detector. The telescopes provide energy resolution of E/E0.3 and angular resolution of 22.5°×36°, and full 4 steradian coverage in one spin (3 s).Top-hat symmetrical spherical section electrostatic analyzers with microchannel plate detectors are used to measure ions and electrons from 3 eV to 30 keV. All these analyzers have either 180° or 360° fields of view in a plane, E/E0.2, and angular resolution varying from 5.6° (near the ecliptic) to 22.5°. Full 4 steradian coverage can be obtained in one-half or one spin. A large and a small geometric factor analyzer measure ions over the wide flux range from quiet-time suprathermal levels to intense solar wind fluxes. Similarly two analyzers are used to cover the wide range of electron fluxes. Moments of the electron and ion distributions are computed on board.In addition, a Fast Particle Correlator combines electron data from the high sensitivity electron analyzer with plasma wave data from the WAVE experiment (Bougeretet al., in this volume) to study wave-particle interactions on fast time scales. The large geometric factor electron analyzer has electrostatic deflectors to steer the field of view and follow the magnetic field to enhance the correlation measurements.     

The solar WIND and suprathermal ion composition investigation on the WIND spacecraft

The Solar Wind and Suprathermal Ion Composition Experiment (SMS) on WIND is designed to determine uniquely the elemental, isotopic, and ionic-charge composition of the solar wind, the temperatures and mean speeds of all major solar-wind ions, from H through Fe, at solar wind speeds ranging from 175 kms^–1 (protons) to 1280 kms^–1 (Fe⁺⁸), and the composition, charge states as well as the 3-dimensional distribution functions of suprathermal ions, including interstellar pick-up He⁺, of energies up to 230 keV/e. The experiment consists of three instruments with a common Data Processing Unit. Each of the three instruments uses electrostatic analysis followed by a time-of-flight and, as required, an energy measurement. The observations made by SMS will make valuable contributions to the ISTP objectives by providing information regarding the composition and energy distribution of matter entering the magnetosphere. In addition SMS results will have an impact on many areas of solar and heliospheric physics, in particular providing important and unique information on: (i) conditions and processes in the region of the corona where the solar wind is accelerated; (ii) the location of the source regions of the solar wind in the corona; (iii) coronal heating processes; (iv) the extent and causes of variations in the composition of the solar atmosphere; (v) plasma processes in the solar wind; (vi) the acceleration of particles in the solar wind; and (vii) the physics of the pick-up process of interstellar He as well as lunar particles in the solar wind, and the isotopic composition of interstellar helium.     

WAVES: The radio and plasma wave investigation on the wind spacecraft

The WAVES investigation on the WIND spacecraft will provide comprehensive measurements of the radio and plasma wave phenomena which occur in Geospace. Analyses of these measurements, in coordination with the other onboard plasma, energetic particles, and field measurements will help us understand the kinetic processes that are important in the solar wind and in key boundary regions of the Geospace. These processes are then to be interpreted in conjunction with results from the other ISTP spacecraft in order to discern the measurements and parameters for mass, momentum, and energy flow throughout geospace. This investigation will also contribute to observations of radio waves emitted in regions where the solar wind is accelerated. The WAVES investigation comprises several innovations in this kind of instrumentation: among which the first use, to our knowledge, of neural networks in real-time on board a scientific spacecraft to analyze data and command observation modes, and the first use of a wavelet transform-like analysis in real time to perform a spectral analysis of a broad band signal.     

SMS建设中系统方法的应用(一)——从系统论的角度认识SMS的本质

<正>当前,安全管理体系(SMS)的建设正在中国民航全面推进;SMS的概念相信已被广泛了解,但是究竟什么是系统方法,如何应用系统方法,在某些单位的SMS建设实践中得不到