含偶氮邻苯二甲腈基团酚醛树脂的合成与性能

利用高邻位酚醛树脂与邻苯二甲腈偶氮盐之间的偶合反应制备了带有邻苯二甲腈基团的新型高邻位酚醛树脂。结构中的腈基在加热条件下可以进行加成固化反应。通过相同方法制备了取代基团含量不同的酚醛树脂并进行了研究。结果表明：最高取代度为89％，随着取代度的增加树脂的分子量呈现出递减的趋势。固化过程中偶氮键在160～230％附近分解，腈基的加成固化出现在260～340％。与传统的酚醛树脂相比，固化后的树脂具有更好的热稳定性和更高的残碳率。     

多炔基加成固化型高残碳酚醛树脂的制备与性能

以碱为催化剂,通过问乙炔基苯基重氮硫酸盐和酚醛树脂间的偶合反应,制备了间乙炔基苯偶氮酚醛树脂(EPAN).树脂的固化由乙炔基的热加成反应实现,无需外加固化剂.该树脂具有固化反应活性高,耐热性好,残碳率高的特点.为了进一步改善该树脂的工艺性,合成了炔丙基基团官能化的乙炔基苯偶氮酚醛树脂(PEPAN),研究了该树脂的工艺性、固化行为以及热性能.研究结果表明,与EPAN相比,树脂的工艺性得到进一步提高,加工窗口明显变宽,树脂固化物的耐热性明显提高,其5%失重温度(Td5)约为432℃,800℃残碳率约为74%.     

镁酚醛树脂的固化特性

文摘采用差示扫描量热法和傅里叶红外光谱法研究了镁酚醛树脂的固化反应特性,包括反应动力学和固化反应机理,热失重研究树脂固化后的耐热性能。研究表明:镁酚醛树脂表观活化能约为82.42 kJ/mol,反应级数为0.913,和普通酚醛树脂固化过程相比反应中有新的结构变化,热失重测试结果表明其耐热性能优异、残碳率较高,在以升温速率为10℃/m in条件下升温至800℃时残碳率可达到58.57%。镁酚醛树脂加热可快速固化,最佳固化成型温度控制在150~160℃。     

苯乙炔基封端PMR型聚酰亚胺树脂的制备与性能研究

使用2,3,3',4'-联苯四酸二酐、对苯二胺和反应性封端剂4-苯乙炔苯酐,采用单体原位反应聚合法制备了设计分子量为1500的PMR型聚酰亚胺树脂PEPA-15.PEPA-15树脂溶液具有良好的室温储存稳定性,我们使用AR-2000流变仪对树脂的熔体加工性能进行了初步测试,树脂经过371℃固化后显示了优异的热稳定性,T300碳纤维增强的复合材料经371℃后固化后在动态热机械分析测试(DMA)中在450℃前储能模量没有明显变化.     

二烯丙基双酚 A 共聚双马来酰亚胺改性氰酸酯树脂的性能

采用二烯丙基双酚A和二苯甲烷型双马来酰亚胺与双酚A型氰酸酯共聚,以改善氰酸酯树脂的工艺和耐热性能;利用DSC,TGA,DMA表征了树脂的固化行为和耐热性能;此外,还研究了树脂的力学性能及高频下的介电性能。结果表明,改性后的氰酸酯树脂固化反应温度降低了约60℃,改性树脂固化物在氮气气氛下Td5约400℃,Tg约270℃,显示了良好的耐热性能。在7~15 GHz宽频范围下,改性树脂的介电常数3,介电损耗0.008~0.01,显示了良好的介电性能。     

低温固化非热压罐成型树脂及其复合材料性能

通过DSC、红外光谱、流变仪和力学性能测试等方法,研究了 3228树脂及T700/3228预浸料的性能.结果表明:3228树脂初始固化温度为67.9℃,峰值固化温度为89.5℃;在60℃时具有大于2 h的低黏度平台期,黏度值在20～30 Pa·s;温度大于65℃后表现出低温快速固化的特性;采用60℃预固化1 h,80℃...     

RTM 用耐高温R802 树脂工艺及性能

研究了RTM用耐高温R802邻苯二甲腈树脂黏度随温度、时间的变化,不同升温速率下的DSC特性,常、高温复合材料弯曲、层间剪切强度、树脂与纤维的界面等。黏度随时间变化曲线表明,其140℃下RTM工艺窗口不少于180 min;DSC曲线表明,在180℃时开始凝胶,固化温度203℃,后处理温度256℃;力学性能测试结果表明,R802/MT300复合材料200℃下弯曲强度保持率为103.8%,500℃下弯曲强度保持率为41.1%,300℃下层间剪切强度较常温提高18%,500℃下层间剪切强度保持率为44%,其树脂与纤维结合良好。     

新型聚苯并噁嗪改性树脂的制备与性能

通过预聚反应制备了一种新型聚苯并噁嗪改性树脂.利用FTIR、GPC表征了改性树脂.利用旋转黏度计、DSC、DMA和TGA分别考察了树脂的流动性能、固化行为和改性树脂固化物的热性能.结果表明:制备的苯并噁嗪改性树脂在60～ 100℃,黏度小于500 mPa·s,恒温6h黏度不明显增大,具有良好的流动性能,适用于RTM成型工艺.改性树脂聚合温度较低,具有良好的固化工艺性.改性树脂固化物在氮气气氛下Td5在430℃以上,在900℃的残重高达73.71％,Ts为353.4℃,具有良好热性能.     

RTM 用R801 树脂工艺及性能

对一种新型RTM用双马来酰亚胺树脂R801的固化反应特性、成型工艺及其制备的复合材料性能进行了研究,DSC曲线表明该树脂体系的固化温度为170～220℃;黏度随温度变化曲线表明在70～120℃,树脂黏度增长缓慢,具有不少于7 h的适用期;在90℃左右时,其初始黏度<100 mPa.s,工艺操作窗口时间≥10 h;该树脂制备的MT300碳纤维复合材料在300℃时的压缩、弯曲、层剪性能保持率均≥63%。     

碳纤维增强耐热环氧树脂复合材料工艺性能研究

研究了一种低黏度耐高温环氧树脂体系的黏温特性及固化反应动力学,考察了该树脂体系的浇注体及其碳纤维复合材料的力学性能,通过热机械分析(DMTA)研究了树脂浇注体及其复合材料的动态热机械性能.结果表明,该树脂体系在室温下黏度为0.3 Pa·s,50℃下适用期在10 h以上,130℃下可以快速固化反应,适合于RTM等快速成型工艺,Tg达到220℃以上,其碳纤维复合材料具有优良的耐高温性能.     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.