共查询到18条相似文献,搜索用时 140 毫秒
1.
基于一种具有串并联混合腿足机构的四足可行走着陆器,为摸清其行走过程中的关节能耗问题,采用牛顿-欧拉方法进行了动力学建模研究。首先,采用D-H法建立串并联混合腿足机构的关节坐标系,进行正向运动学和逆向运动学的推导;然后在运动学模型的基础上,采用牛顿-欧拉方法建立着陆器整机的全状态动力学模型,该模型以足端相对轨迹为输入,获取着陆器在运动过程中各关节受力情况的变化曲线;最后,采用五次样条插值法规划一段运动轨迹,用ADAMS仿真软件进行着陆器虚拟样机仿真。经验证,该动力学模型理论计算数值和虚拟样机仿真数值具有相同的变化趋势,证明了模型的有效性,可以作为后续能耗模型建立和优化的基础。 相似文献
2.
3.
4.
5.
<正>近日,嫦娥三号着陆器相机指向机构顺利完成休眠唤醒后的再次转动拓展任务,主要包括俯仰及航向正反向各种状态的运动功能测试和各状态下限位开关触发测试。通过遥测数据分析,本次任务所有测试项目均正确执行,转动方向及运行时间与设计值保持一致,到位触发信号正常,标志着嫦娥三号探测器着陆器相机指向机构顺利完成在轨拓展工作目标。2013年12月2日,嫦娥三号着陆器相机指向机构伴随嫦娥三号探测器由长征三号乙 相似文献
6.
7.
月球着陆器着陆缓冲性能研究 总被引:5,自引:0,他引:5
首先基于MSC.Nastran/MSC.Adams软件建立了模拟月球着陆器的动力学模型,并利用模拟月球着陆器在地面冲击试验来验证仿真模型的正确性,重点关注缓冲机构与结构连接处的载荷,结构特征点的加速度响应,以及缓冲器的工作行程。然后利用模拟着陆器地面试验结果修正动力学分析模型,研究表明:着陆器结构和缓冲机构的柔性对缓冲性能具有较大的影响。最后,把动力学分析模型中的模拟结构更换成真实结构,进行着陆器在月球表面的着陆冲击仿真分析,从而获得模拟着陆器地面试验与着陆器在月面着陆的冲击缓冲性能差异。 相似文献
8.
航天器半物理仿真应用研究 总被引:1,自引:0,他引:1
介绍了航天器半物理仿真的特点,总结了航天器控制系统半物理仿真的3种基本表现形式和应用范围。指出在没有特殊说明时,传统意义上的控制系统半物理仿真是指以敏感器/控制器在回路为主要框架的仿真试验,其特点是有复杂昂贵的运动模拟器等仿真专用设备,其关键技术之一是运动模拟器的设计应用技术,具体可分为基于运动学直接物理模型和基于运动学数学模型变换2种方法,并在仿真应用举例中对此作了进一步说明。 相似文献
9.
10.
文章主要讨论两种类型的着陆器,即硬式着陆器和半硬式着陆器。介绍了利用动态分析方法探究作用在着陆器和平台上的冲击载荷及着陆缓冲装置的有效性的过程和结论,最后建议性的提出了着陆缓冲器的初样设计方案。 相似文献
11.
Optical navigation for a lunar lander consists of estimating a lander's 3-dimensional (3-D) relative dynamic motion with respect to a preselected landing site using a passive 2-dimensional (2-D) video image sequence. Lunar landing missions require a lander to perform an autonomous accurate landing with simple mechanical structure, easy operation and low cost. These requirements have motivated the need to develop an advanced navigation system. Existing navigation systems trade-off simplicity, accuracy and cost. High accuracy navigation systems typically imply complexity and high cost. In this paper, we consider a scenario where the descending phase starts from an initial altitude of 10 km with a time-of-descent of 100 s. The navigation camera is an off-the-shelf optical instrument used to take the video image sequence of the landing site during the landing phase. It is fed into the motion estimation algorithm to be processed. The continuous wavelet transform (CWT) is used to analyse each image frame of the input digital video image sequence. The output is a 2-D video image motion trajectory map, which represents the projection motion of the landing site. The 2-D video image motion is projected back to the 3-D lander's relative motion based on a geometric analysis. The outputs of this estimation algorithm are the 3-D attitude motion parameters of the lander at a time corresponding to an image being taken. The attitude determination and control system (ADCS) of the lander uses these data to perform the lander's attitude control task. In this article, we provide the motion modelling for a lunar lander during the descending phase. The projection of a 3-D planar to 2-D image plane is analysed which build the correspondence between the 3-D lander's motion and the 2-D image motion. This link provides the evidence for the geometry analysis. CWT is reviewed and CWT for video image sequence analysis is also introduced. Numerical simulation of the estimated 2-D video image sequence under the lander performing a 3-D translation and yaw rotation during the terminal descent are shown to verify the proposed concepts. The analysis of the results show that the proposed method achieves highly accurate 2-D video image motion estimation of less then 1% error with significant savings of cost, mass and volume. It leads to the accurate estimation of the lander's 3-D relative motion with respect to the landing site. 相似文献
12.
13.
为提高月球着陆器着陆可靠性,需识别潜在的故障模式对稳定性着陆带来的影响。建立了着陆器的动力学模型,给出了着陆器着陆时的七种极限工况,作为故障模式分析的基础;针对动力下降段三种典型故障模式,即主发动机延时关机、储箱残留液体着陆和触月信号延迟发出,建立与延时关机对应的上抛、平抛运动和数学关系,与残留液体着陆等效的单摆模型,施加触月信号延迟发出所产生的推力曲线,利用Adams软件进行动力学仿真;结果表明储箱残留液体着陆影响较小,另外两种故障模式使着陆时抗倾倒性能和缓冲性能恶化,增加着陆不稳定性。 相似文献
14.
针对传统着陆器缓冲装置无法复用的不足,提出了一种可重复使用的小型着陆器,通过各关节上的摩擦制动装置吸收着陆冲击能量,由电机及扭簧组件实现再次起飞后着陆腿的姿态恢复,可满足多点飞跃探测的月表探测任务。完成了一维落震中单套着陆腿在竖直方向上的缓冲吸能动力学分析;基于径向基(RBF)代理模型,面向三种典型着陆工况,采用多目标协同优化方法,对单套着陆腿各关节制动扭矩进行了优化,优化后的缓冲吸能关节可有效降低着陆器在落震过程中的加速度峰值。最后进行了整机多工况落震仿真分析,结果表明,各着陆响应均满足设计要求,也可保证良好的着陆过程稳定性,可为中国后续开展星表单次任务多点位探测提供一种可行的解决方案。 相似文献
15.
16.
17.
国外深空探测器着陆缓冲系统的特点和应用 总被引:1,自引:0,他引:1
主要介绍国外月球和行星探测器的着陆缓冲系统的特点与应用。着陆缓冲系统的基本类型包括软着陆机构、气囊缓冲装置和空中悬吊机结构。其中:软着陆机构由着陆架(腿)、缓冲器和展开锁定机构组成,具有质量较大,结构较简单、可靠的特点,在美国“勘测者”、“阿波罗”、“梦神”和苏联月球号等着陆器中得到了应用;气囊缓冲装置由气体发生器、气囊组件,以及缩回与展开机构组成,具有质量小、包装容积小和着陆稳定性好的特点,在美国“火星探路者”、“火星探测巡视器”,苏联早期月球号着陆器,以及欧洲“贝皮一哥伦布”水星探测器中得到了应用;空中悬吊机结构由空中悬吊机及其推进系统等组成,具有着陆速度低、冲击小和安全可靠的特点,在美国“火星科学实验室”的好奇心号巡视器上得到了应用。 相似文献
18.
随着中国深空探测的发展,在月球表面进行着陆探测成为新的关注热点,因此月球着陆器的着陆稳定性研究成为一项重要课题。文章利用ADAMS软件及其用户子程序,对一种可展开四腿式月球着陆器的着陆稳定性进行了研究,研究结论为着陆器的着陆缓冲机构及总体设计提供参考。 相似文献