递推阻尼最小二乘法及其在火控系统中的应用

由于火控系统误差模型未知且稳定性较差,采用Kalman滤波实现滤波时,其滤波特性较差;而此时最小二乘法是实际工程应用中的常用方法,但是容易产生参数爆发现象。文中提出了一种基于多输入-多输出(MI-MO)系统的递推阻尼最小二乘法,将其应用到火控滤波系统中。仿真结果表明,利用递推阻尼最小二乘法能达到递推最小二乘法同样的精度,且能明显抑制参数爆发现象,达到良好的滤波效果。     

铣削过程在线辨识与极点配置自适应控制

 研究了铣削加工过程的建模、参数在线辨识及自适应控制问题,为铣削过程建立了二阶离散传递函数模型,提出了一种修正的带遗忘因子递推最小二乘参数辨识算法,从而解决了普通递推最小二乘辨识算法中由于递推计算协方差矩阵衰退或膨胀引起辨识结果失真的问题,采用极点配置设计原理,为铣削过程推导了自适应控制的控制律。仿真和实验表明,修正的最小二乘辨识算法和极点配置自适应控制律是正确和可靠的,自适应控制器可获得所需的响应性能。     

基于最小二乘法的飞航导弹速度信息融合研究

提出了利用最小二乘法融合北斗双星定位系统和平台惯导系统的数据,估计飞航导弹的速度误差参数,用以修正惯导长时问运行产生的速度漂移,也提出了利用雷达给出的视线角和视线距信息修正惯导的速度信息.数据融合采用了线性、非线性、无限时间域递推、有限时间域递推等多种最小二乘算法,分别对它们进行了数学仿真,结果显示了该算法的有效性.     

磁悬浮电励磁三相直线同步电机离线参数辨识

建立磁悬浮电励磁三相直线同步电机(MSEETPLSM)的连续时间参数型状态空间方程数学模型,利用前向一阶差分方法将连续时间数学模型离散化成离散时间参数型状态空间方程数学模型,再利用z变换写成递推最小二乘算法标准形式的数学模型。利用递推最小二乘算法在初级转子静止状态下辨识出MSEETPLSM的电阻及自感参数。利用计算机数值仿真软件仿真MSEETPLSM参数的离线辨识算法,得到MSEETPLSM的初级与次级电阻与电感时域辨识曲线,仿真曲线收敛速度较快且辨识精度较高。仿真结果验证了该参数离线辨识算法的有效性。     

最小二乘法述评

本文在简要回顾了最小二乘法的发展过程后,论述了该方法的基本原理和特点。接着分析了最小二乘法存在的主要问题。由于实际情况往往偏离假设条件,故常常影响该法的实用效果。最后介绍了长期以来人们对最小二乘法所作的种种改进(如:递推最小二乘法、卡尔曼滤波法、最小二乘拟合推估法、稳健估计法和“最小风险估计”法等),并对各方法作了简要评述。     

MATLAB在动态称量中的应用

利用MATLAB语言编程来识别定量称量系统的参数，显示了递推最小二乘算法易于在线识别的特点和MATALAB在系统识别应用中的广阔前景。     

自旋稳定卫星姿态参数递推容错LS估计

准确计算自旋稳定卫星姿态参数是正确实施姿态控制的前提。本文基于最小二乘（LS）理论，建立了在线计算卫星姿态参数的一组具有容错功能的递推LS算法，简要论证了该算法具备良好的统计最优性质。     

石英加速度计误差模型系数的递推最小二乘辨识方法研究

为探索在线辨识的测试方法,满足实时辨识的需要,本文提出采用递推最小二乘法辨识石英加速度计模型系数,并对其在重力场测试中的应用进行了研究.介绍了递推最小二乘系数估计法原理,为便于实际应用,根据测试领域的习惯,对递推最小二乘方法进行了梳理.以加速度计分度头试验为例,将该方法应用于加速度计重力场试验的误差模型系数辨识.仿真分...     

用逐步扩阶双递推时域法识别线性振动系统复模态参数

本文给出了从线性振动系统的自由响应识别该系统复模态参数的方法,把自由响应的表达式变为一个自回归方程和一个多项式方程,利用最小二乘递推与逐步扩阶递推的双递推法来进行参数识别。文中讨论了几个应用中的问题,并给出了计算机的模拟计算结果以及越野汽车车架的参数识别试验结果。     

基于自适应PID的异步电机电流控制

在异步电机矢量控制电流环中采用参数自适应PID算法。该算法采用带遗忘因子的递推最小二乘算法对PID参数进行在线估计,能够根据不同情况实时调整PID参数。试验结果表明,该算法鲁棒性强、稳定性好、自适应性强、计算量小,能够满足对电流控制的要求,并且提高了速度的抗干扰能力。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.