改性三元乙丙橡胶用于红外隐身涂层的研究

采用正交试验制备了三元乙丙橡胶接枝马来酸酐(EPDM-g-MAH),并以此为黏合剂,铜粉为填料制备了发射率可调的热红外隐身涂层,对涂层进行了红外光谱、红外发射率、微观形貌、力学性能等方面的分析.结果表明该涂层发射率可低至0.15左右,且可以显著减少填料的用量,明显提高涂层的力学性能:附着力可以从3级提高到1级,铅笔硬度从2B提高到3H,柔韧性都为1 mm,耐冲击力都大于50 cm.根据正交试验得到了优化试验条件,获得了涂层力学性能较好、红外发射率低的黏合剂材料.     

我国航空发动机用几种涂层技术的差距及未来发展

论述了航空发动机隐身、抗冲蚀、防钛火涂层的技术现状.强调研究多元合金化及复合冲蚀涂层、阻燃涂层及阻燃性能测试技术,研究强吸波和低红外发射涂层、宽频带和多频谱隐身、雷达与红外隐身兼容涂层,以促进我国隐身战机的研制.     

1种低红外发射率涂层耐热性能研究

为有效降低飞行器高温部位表面的红外发射率,以改性有机硅为黏结剂体系、金属铝粉为主要填料,制备了在8~14μm波段具有较低红外发射率的涂层。在50~400℃温度范围内考察了涂层的耐热性能,并采用扫描电镜、TGA等手段对其进行表征,研究了涂层的红外发射率、光泽度和力学性能随温度的变化规律及影响机理。结果表明:制备的涂层在300℃以下具有良好的力学性能,可长期使用,在8~14μm波段的红外发射率与温度成反比,光泽度与温度成正比;当环境温度高于300℃,涂层开始发生热降解现象,光泽度降低,涂层的力学性能降低。     

红外隐身涂料的研究进展

介绍了红外隐身材料国内外研究进展情况,包括构成红外隐身材料的填料、树脂及其红外性能的各种影响因素,最后还介绍了与雷达隐身材料的兼容性问题。     

雷达/激光复合隐身材料的实验研究

采用双层涂敷法,在雷达隐身材料表层喷涂薄层的激光隐身材料,制备了双层型雷达/激光复合隐身材料,并用紫外-可见-近红外分光光度计分别测试了涂敷激光涂层前后的激光反射率以及在微波暗室内测试了涂敷激光涂层前后的雷达波反射率.结果表明：涂敷激光涂层后,在1.06 μm处的反射率由2.24%降低到0.13%,在8～15 GHz范围内,对雷达波反射率没有不利影响,均小于-7.5 dB,且有一定的改善,显示该材料在8～15 GHz范围内可以很好地实现雷达与激光的复合隐身,在其他波段的兼容性有待于进一步研究.     

低发射率薄膜的红外隐身特性研究

利用磁控溅射法制备了氧化铟锡（ITO）、掺铝氧化锌（ZAO）、TiO2/Ag/TiO2纳米多层等三种透明的低发射率薄膜。研究了这些低发射率薄膜以及降低材料红外发射率对降低红外辐射强度和红外隐身所起的作用。结果表明：降低红外发射率可以有效地抑制由于温度升高所带来的附加红外辐射;低红外发射率薄膜在红外隐身中有潜在应用价值。     

多谱兼容隐身材料研究（上）——降温吸波多谱兼容隐身涂料的可能性模型

隐身材料是实现目标隐身的重要途径。随着侦察技术的多频谱（可见光、红外和雷达等多种侦察谱段）化，隐身技术和隐身材料的研究必须满足多谱要求。本文通过对单层涂料与电磁波相互作用分析，建立雷达波吸收模型，预测达到目标吸波技术指标所需要选择的材料的范围；利用能量守恒原理，通过在该层涂料上建立太阳加热后涂料与目标周围环境动态热平衡模型方法，预测降温效果，为材料研制选择技术参数指明方向。通过上述雷达波吸收和热红外降温模型的建立和求解分析，预测单一涂料对地面目标雷达与红外兼容隐身，通过材料参数调整和设计是可能的，为兼容性多谱隐身材料的研制指明的方向。     

飞行器红外隐身效能工程评价方法

 针对飞行器的红外隐身问题,推导出红外辐射对比度与作用距离的理论关系,采用指数拟合获得大气透过率与作用距离的近似关系表达式,简化了对作用距离的计算,并通过实际算例考察了目标表面温度、目标发射率和飞行速度对红外辐射对比度及作用距离的影响。结果表明：对比度和作用距离随目标表面温度、发射率及飞行速度的下降趋势基本一致;在一定条件下,对比度可代替作用距离作为评价目标红外隐身效果的简单、快速的参数,对比度越小目标的红外隐身效果越好。对比度的计算快速、准确、灵活性强和适用范围广,为今后进一步对飞行器的红外隐身研究提供一定的理论参考。     

红外隐身材料的现状与展望

综述了国内外红外隐身材料的发展历程，重点介绍了构成红外隐身材料的填料、树脂的研究现状以及近年来开始重点研究的红外兼容型多频谱隐身材料，并且指出了红外隐身材料的发展方向。     

导电高分子电致变色智能热控器件

采用简单的旋涂、喷涂等方法,制备了一种由可溶性聚苯胺为主体电致变色智能热控器件.该器件的基底为聚酯,固体电解质为锂盐/聚丙烯腈.通过电切换调控,该器件发射率能够在0.46-0.75内调控,且红外光谱反射率变化大于38%.研究了厚度、预掺杂酸种类、浓度等对聚苯胺活性层发射特性的影响;考察了导电高分子聚苯胺层厚度、电切换电压等因素对涂层体系发射率调控的影响.结果表明发射率的调控范围与电化学还原的深度密切相关,通过调节材料厚度、掺杂酸种类等可有效提高发射率调控范围.该导电高分子电致变色智能热控涂层在航天器热控制方面展示了良好的应用前景.     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.