Springback prediction of thick-walled high-strength titanium tube bending

Significant springback occurs after tube rotary-draw-bending （RDB）, especially for a high-strength Ti-3A1-2.5V tube （HSTT） due to its high ratio of yield strength to Young＇s modulus. The combination scheme of explicit and implicit is preferred to predict the springback. This simulation strategy includes several numerical parameters, such as element type, number of elements through thickness （NEL）, element size, etc. However, the influences of these parameters on spring- back prediction accuracy are not fully understood. Thus, taking the geometrical specification 9.525 mm × 0.508 mm ofa HSTT as the objective, the effects of numerical parameters on prediction accuracy and computation efficiency of springback simulation of HSTT RDB are investigated. The simulated springback results are compared with experimental ones. The main results are： （1） solid and continuum-shell elements predict the experimental results well; （2） for C3DSR elements, NEL of at least 3 is required to obtain reliable results and a relative error of 29% can occur as NEL is varied in the range of 1-3; （3） specifying damping factor typically works well in Abaqus/Emplicit simulation of springback and the springback results are sensitive to the magnitude of damping factor. In addition, the explanations of the effect rules are given and a guideline is added.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

Surface integrity and fatigue behavior when turning γ-TiAl alloy with optimized PVD-coated carbide inserts

This paper presents a comprehensive investigation on the effects of tool and turning parameters on surface integrity and fatigue behavior in turning c-Ti Al alloy. The wear of inserts surface, cutting forces, and surface roughness were studied to optimize PVD-coated carbide inserts.Surface topography, residual stresses, microhardness, and microstructure were analyzed to characterize the surfaces layer under different turning parameters. Surface integrity and fatigue life tests of c-Ti Al alloy were conducted under turning and turning-polishing processes. The results show that compared to CNMG120412-MF4, CNMG120408-SM is more suitable because it obtained low cutting force, surface roughness, and tool wear. With increasing the cutting speed and depth, the depths of the compressive residual stress layer, hardening layer, and plastic deformation layer increased. For turning and turning-polishing specimens, the compressive residual stress was relaxed by less than 20%–30% after 10~7 cycles. The fatigue life of a turning-polishing specimen with R_a= 0.15 mm has increased 3 times from that of a turning specimen with R_a= 0.43 mm.     

Tribological evaluation of surface modified H13 tool steel in warm forming of Ti–6Al–4V titanium alloy sheet

The H13 hot-working tool steel is widely used as die material in the warm forming of Ti–6Al–4V titanium alloy sheet. However, under the heating condition, severe friction and lubricating conditions between the H13 tools and Ti–6Al–4V titanium alloy sheet would cause difficulty in guaranteeing forming quality. Surface modification may be used to control the level of friction force, reduce the friction wear and extend the service life of dies. In this paper, four surface modification methods(chromium plating, TiAlN coating, surface polishing and nitriding treatment)were applied to the H13 surfaces. Taking the coefficient of friction(CoF) and the wear degree as evaluation indicators, the high-temperature tribological behavior of the surface modified H13 steel was experimentally investigated under different tribological conditions. The results of this study indicate that the tribological properties of the TiAlN coating under dry friction condition are better than the others for a wide range of temperature(from room temperature to 500 C), while there is little difference of tribological properties between different surface modifications under graphite lubricated condition, and the variation law of CoF with temperature under graphite lubricated is opposite to that under the dry friction.     

Testing and evaluation for fatigue crack propagation of Ti-6Al-4V/ELI and 7050-T7452 alloys at high temperatures

This paper seeks to evaluate crack propagation properties and residual lives of metallic alloys subjected to fatigue loading at room and high temperatures. Fatigue crack growth tests were performed on Ti-6Al-4V/ELI and 7050-T7452 subjected to constant-amplitude and actual randomspectra loading at room temperature of about 25 ℃ and at high temperatures of 250 ℃ and 150 ℃ to determine their crack growth properties and residual lives. The damage mode and mechanisms at high temperature were compared with those at room temperature on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectra load history were evaluated based on a modified accumulation damage rule accounting for the load interaction.Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.     

Yield anisotropy and tension/compression asymmetry of a Ni3Al based intermetallic alloy

In order to investigate the yielding behavior of the newly developed Ni 3 Al-based intermetallic alloy IC10, yield stresses have been measured in tension and compression with different orientations. The specimens were cut from a sheet with different angles inclined from the solidification direction. The inclined angles were taken to be 0 , 22.5 , 45 , 67.5 and 90 . All experiments were conducted at room temperature except for orientation 0 , whose deformation temperatures ranged from 298 to 1273 K. Experimental results show that the yield strength of alloy IC10 has the anomalous behavior which has been observed for other Ll 2 -long-range ordered intermetallic alloys, but it is less pronounced. The abnormalities show the following characteristics: (i) the yield strength increases as the temperature is raised below the peak temperature, (ii) yield strength anisotropy, (iii) tension/compression asymmetry. Compared to Ni 3 Al single crystals, the polycrystalline exhibits some different yielding behaviors which may be due to the high volume fraction of c phase.     

Temperature effect on buckling properties of ultra-thin-walled lenticular collapsible composite tube subjected to axial compression

This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.     

Low-frequency unsteadiness of vortex wakes over slender bodies at high angle of attack

A type of flow unsteadiness with low frequencies and large amplitude was investigated experimentally for vortex wakes around an ogive-tangent cylinder. The experiments were carried out at angles of attack of 60–80 and subcritical Reynolds numbers of 0.6–1.8×105. The reduced frequencies of the unsteadiness are between 0.038 and 0.072, much less than the frequency of Karman vortex shedding. The unsteady flow induces large fluctuations of sectional side forces. The results of pressure measurements and particle image velocimetry indicate that the flow unsteadiness comes from periodic oscillation of the vortex wakes over the slender body. The time-averaged vortex patterns over the slender body are asymmetric, whose orientation is dependent on azimuthal locations of tip perturbations. Therefore, the vortex oscillation is a type of unsteady oscillation around a time-averaged asymmetric vortex structure.     

Ignition enhancement of ethylene/air by NOx addition

Recently, non-equilibrium plasma assisted combustion (PAC) has been found to be promising in reducing the ignition delay time in hypersonic propulsion system. NO x produced by non-equilibrium plasma can react with intermediates during the fuel oxidation process and thereby has influence on the combustion process. In this study, the effects of NO x addition on the ignition process of both the homogeneous ethylene/air mixtures and the non-premixed diffusion layer are examined numerically. The detailed chemistry for ethylene oxidization together with the NO x sub-mechanism is included in the simulation. Reaction path analysis and sensitivity analysis are conducted to give a mechanistic interpretation for the ignition enhancement by NO x addition. It is found that for both the homogenous and non-premixed ignition processes at normal and elevated pressures, NO 2 addition has little influence on the ignition delay time while NO addition can significantly promote the ignition process. The ignition enhancement is found to be caused by the promotion in hydroxyl radical production which quickly oxidizes ethylene. The promotion in hydroxyl radical production by NO addition is achieved in two ways:one is the direct production of OH through the reaction HO2+NO = NO2+OH, and the other is the indirect production of OH through the reactions NO+O2=NO2+O and C2H4+O = C2H3+OH. Moreover, it is found that similar to the homogeneous ignition process, the acceleration of the diffusion layer ignition is also controlled by the reaction HO2+NO = NO2+OH.     

Effects of different aging treatments on microstructures and mechanical properties of Al-Cu-Li alloy joints welded by electron beam welding

Post-weld single aging treatment(solution treatment at 510 ℃ for 1 h, water quenching,and aging at 155 ℃ for 16 h) and post-weld double aging treatment(solution treatment at 510 ℃ for 1 h, water quenching, aging at 155 ℃ for 16 h, and aging at 130 ℃ for 12 h) are carried out on Al-Cu-Li alloy joints by electron beam welding(EBW) respectively. The effects of aging treatments on microstructures and mechanical properties of welded joints are investigated. Results show that the mechanical properties of welded joints are obviously improved after both aging treatments. The strength coefficient of joints is increased from 0.64 in an as-welded condition(AW) to 0.90 after post-weld double aging treatment. Microstructure analysis shows that the precipitates of the fusion zone within grains and grain boundaries are less in the AW condition. After post-weld heat treatment(PWHT), a lot of fine needle-like phases T_1(Al_2 Cu Li) precipitate in grain boundaries of the fusion zone, and more horseshoe-shaped β' (Al_3 Zr) particles precipitate within grains. In addition,grains of the fusion zone are refined after post-weld double aging treatment, which leads to an effect of grain refinement strengthening. Consequently, the mechanical properties of welded joints are greatly improved.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

4种典型航空钛合金材料高温裂纹扩展性能对比试验

试验测定了4种典型航空钛合金材料（即TC18、TC21、TC4 DT、Ti 6Al 4V/ELI）在两种温度（25℃和250℃）下裂纹扩展性能,在试验数据的基础上,进行裂纹扩展性能对比分析,并对试样断口进行扫描电镜(SEM)分析,研究了高温和载荷联合作用对裂纹扩展的影响机理,结果表明:不同温度下,不同钛合金材料裂纹扩展速率之间存在很大的差异性;与室温断口相比,高温断口表面呈现浅黄色,并伴有大量二次裂纹;钛合金的裂纹扩展性能是受温度和载荷的联合作用影响,裂纹闭合和氧化作用共同决定了其扩展历程。      

Effect of dilution holes on the performance of a triple swirler combustor

A triple swirler combustor is considered to be a promising solution for future high temperature rise combustors. The present paper aims to study dilution holes including primary dilution holes and secondary dilution holes on the performance of a triple swirler combustor. Experimental investigations are conducted at different inlet airflow velocities(40–70 m/s) and combustor overall fuel–air ratio with fixed inlet airflow temperature(473 K) and atmospheric pressure. The experimental results show that the ignition is very difficult with specific performance of high ignition fuel–air ratio when the primary dilution holes are located 0.6H(where H is the liner dome height)downstream the dome, while the other four cases have almost the same ignition performance. The position of primary dilution holes has an effect on lean blowout stability and has a large influence on combustion efficiency. The combustion efficiency is the highest when the primary dilution holes are placed 0.9H downstream the dome among the five different locations.For the secondary dilution holes, the pattern factor of Design A is better than that of Design B.     

整体加筋壁板的破损安全特性与断裂控制分析

用有限元和断裂力学方法分析大型整体机翼下壁板的破损安全特性。对一个九桁条铝合金整体加筋板,裂纹从断裂筋条下向两侧均匀扩展的开裂形式,进行了应力强度因子和剩余强度计算,并和另一个具有相同构形的铆接加筋板的结果进行对比。当裂纹长度在两倍桁条间距以内时两种加筋板的剩余强度水平相当。但是当整体壁板中的裂纹穿过外侧相邻桁条时,整体桁条的止裂能力逐渐减弱。研究对整体壁板蒙皮胶接止裂条的断裂控制措施及有限元建模分析方法,描述止裂条胶层局部脱粘的处理方法和迭代过程。止裂条材料分别选用了钛合金和单向层压复合材料。计算结果说明胶接止裂措施能显著提高整体加筋板的破损安全性能。     

Radical recombination in a hydrocarbon-fueled scramjet nozzle

To reveal the radical recombination process in the scramjet nozzle flow and study the effects of various factors of the recombination, weighted essentially non-oscillatory(WENO)schemes are applied to solve the decoupled two-dimensional Euler equations with chemical reactions to simulate the hydrocarbon-fueled scramjet nozzle flow. The accuracy of the numerical method is verified with the measurements obtained by a shock tunnel experiment. The overall model length is nearly 0.5 m, with inlet static temperatures ranging from 2000 K to 3000 K, inlet static pressures ranging from 75 k Pa to 175 k Pa, and inlet Mach numbers of 2.0 ± 0.4 are involved.The fraction Damkohler number is defined as functions of static temperature and pressure to analyze the radical recombination progresses. Preliminary results indicate that the energy releasing process depends on different chemical reaction processes and species group contributions. In hydrocarbon-fueled scramjet nozzle flow, reactions with H have the greatest contribution during the chemical equilibrium shift. The contrast and analysis of the simulation results show that the radical recombination processes influenced by inflow conditions and nozzle scales are consistent with Damkohler numbers and potential dissociation energy release. The increase of inlet static temperature improves both of them, thus making the chemical non-equilibrium effects on the nozzle performance more significant. While the increase of inlet static pressure improves the former one and reduces the latter, it exerts little influence on the chemical non-equilibrium effects.     

裂纹扩展的无网格数值模拟方法

疲劳断裂是航空材料的重要失效形式 ,由于裂纹尖端应力存在奇异性 ,传统有限元方法模拟裂纹沿任意路径扩展存在很多不足。作为一种新兴的数值模拟方法 ,无网格计算只需将求解问题离散为独立的节点 ,计算过程中可以实时跟踪裂纹尖端区域进行局布细化。将连续的裂纹扩展过程看作多个线性增量 ,每一个增量内裂纹扩展角根据应力强度因子确定 ,通过在裂纹尖端细化节点和引入外部基函数提高了计算精度。本文给出了应用无网格方法模拟裂纹扩展过程的关键技术和计算流程 ,通过对带有中心斜裂纹的 Ti-6 Al-4 V合金平板进行分析 ,预测得到的裂纹扩展路径与实验值吻合的较好。     

Ti合金与SiC_p/Al复合材料在无压浸渗同步复合过程中的相容性

采用熔铝无压浸渗复合工艺在高体份SiCp／Al复合材料制备过程中同步复合Ti合金零部件（圆柱体）,研究了这种跨宏-微观尺度、超混杂铝基复合材料的微观组织及性能,特别是SiCp／Al复合材料与Ti合金零部件之间的相容性。结果表明,复合材料性能优异、组织致密,SiC颗粒分布均匀、无偏聚现象。SiCp／Al复合材料与Ti合金之间的界面结合非常紧密,Ti元素向铝合金基体一侧有一定距离的扩散,并且出现了可增强界面结合的连续、无缺陷的界面反应物薄层,SEM和XRD分析表明界面反应产物为Al2Ti,界面剪切强度超过200MPa,完全可以满足在复合材料中的Ti合金零部件处加工装配孔的要求。     

An approach for parameter estimation of combined CPPM and LFM radar signal

In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation (CPPM) and linear frequency modulation (LFM), which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval (PRI) of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform (CHT) algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio (SNR) is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.     

钛合金扩散焊接头复合型疲劳裂纹扩展

设计并加工了TC4扩散焊接头紧凑拉伸剪切(CTS)试样。开展了不同加载角度下的Ⅰ-Ⅱ复合型疲劳裂纹扩展试验。试验结果发现:在加载角度小于45°时,裂纹均沿焊缝扩展至断裂,当加载角度达到45°以上时,裂纹开始出现沿与初始裂纹面呈一定角度的方向扩展至母材的情况。使用电子显微镜结合电位法获得了裂纹扩展a-N曲线。在此基础上,采用相互作用积分法计算复合型应力强度因子,以应变能释放率为参量对Ⅰ-Ⅱ复合型裂纹扩展过程进行了分析。考虑Ⅱ型裂纹所占权重引入复合比,并在此基础上建立了TC4扩散焊接头不同加载角度及载荷下Ⅰ-Ⅱ复合型疲劳裂纹扩展速率统一模型。