共查询到20条相似文献,搜索用时 937 毫秒
1.
用Dynaform有限元仿真软件对阶梯形件液压拉深成形过程进行了模拟,分析了压边力和液体压力对阶梯形件成形质量的影响。研究结果表明,合适的压边力和液体压力能防止阶梯形件拉深缺陷的发生。 相似文献
2.
3.
4.
5.
薄壁内、外半管冲压成形工艺参数模拟优化设计 总被引:2,自引:0,他引:2
针对内、外半管的结构特点,分析计算冲压成形主要工艺参数及毛坯尺寸,运用有限元分析软件ANSYS/LS-DYNA,对内、外半管的成形过程进行了模拟。研究了不同压边力及不同冲压速度对零件拉深成形的影响,分析了零件的成形工艺及其起皱缺陷,优化了毛坯形状,避免了成形过程中的缺陷,获得了理想的毛坯形状和工艺参数。 相似文献
6.
7.
薄壁圆筒加对轴向压力液压成形是一种新型成形工艺.然而,目前对变形力的确定几乎都采用自己一套适用性很狭的经验公式,.或采用大吨位的压力机盲目试探,而无一种预先确定变形力的工程计算公式.该文依据塑性变形的从本方程式和塑性力学理论,用应力分析法对加轴向力液压成形变形力进行了理论解析,且根据工件几何尺寸,作为液压成形的理论依据. 相似文献
8.
9.
10.
对某型号导弹包装箱体和箱盖零件拉深成形的工艺方案进行了分析,介绍了所设计的一次拉深成形模具的结构和特点,该模具适用于成形箱体和箱盖两个零件,有效地控制了工装成本并使箱体和箱盖零件的尺寸协调一致。 相似文献
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
13.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
14.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
15.
16.
17.
18.
金属网由于柔韧性好、使用方便等优势而在电缆屏蔽工程上得到广泛应用。本文对电缆用的金属网屏蔽效能进行工程计算,通过计算,对金属网不同材料、不同规格、单层与双层屏蔽及有缝隙情况下的屏蔽效能进行比较与分析,对工程应用有一定的指导意义。 相似文献
19.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
20.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献