An Optimum Phase Reference Detector for Fully Modulated Phase-Shift Keyed Signals

Many modern telemetry systems which use phase-shift keying (PSK) have receivers which derive a coherent reference from the fully modulated PSK signal itself and thus conserve the energy which otherwise would be allocated to a discrete reference signal. In this paper, an optimum receiver structure for estimating a phase reference from the PSK signal itself is derived and its realization discussed. It is shown that at low signal-to-noise ratios, the optimum detector can be realized with a Costas loop. Since a Costas loop and squaring loop exhibit identical performance, it follows that either of these simple devices gives optimum performance for low-input signal-to-noise ratios.     

Exact Formulation of Window Functions for Analog Network Spectral Analyzers

An equation for the spectral window function for analog network analyzers is derived without assumptions on length of data interval available. The equation, given in terms of filter pole-zero locations for both the filter-bank and heterodyned-input type analyzers, can be programmed on a digital computer without difficulty. As an illustration, the "growth" of a spectral window with increasing length of available data is shown for a special case: a single-tuned circuit followed by a squaring circuit and perfect integrator. The error in using the usual approximation also is indicated. Use of the derived equation for quantitative comparisons of analog and digital analyzers is noted.     

Phase-Frequency Detection in Sampled Phase-Locked Frequency Mlultipliers

Phase-locked high-frequency multipliers which do not have powergreedy frequency dividers in the feedback loop, but which do have a sample-and-hold circuit as a phase detector are hard to design, due to conflicting requirements which determine the choice for loop gain and loop bandwidth. A circuit is described that acts as a frequency control if the loop is not locked and as a phase control once the loop can be locked. The loop filter has to be optimized for the locked condition only, and the allowable preset error is more than 80 percent of the sample frequency. The circuit also indicates whether the oscillator frequency is an odd or an even multiple of the sample frequency. Pull-in is at least an order of magnitude faster than with phase control alone.     

静电悬浮微机械加速度计检测电路设计

静电悬浮微机械加速度计通过静电力把质量块无接触的悬浮起来,具有极高的分辨率.一般采用差动电容式位移检测的方式来精确检测质量块在电极腔内的运动,然后在通过悬浮控制系统来实现六自由度的有源悬浮.针对该电容的检测,本文介绍了一种基于环形二极管解调的单频载波公共激励电极电容式多路位移检测方案,并进行了设计仿真与实验测试,实验测...     

基于提前停止判决的编码软信息辅助载波同步

 针对目前编码辅助载波同步算法中复杂度较高、延时大的问题,提出了引入辅助停止判决机制的编码辅助载波同步算法。在现有的编码辅助载波同步结构基础上,该算法能对环路信噪比(SNR)进行实时判定,在环路SNR满足限定条件后提前停止编码辅助载波同步迭代,而不影响译码性能。采用新的相位估计方式估计含相位噪声的载波相位,提升了该条件下的环路信噪比。仿真采用码率为1/2的低密度奇偶校验(LDPC)码作为编码方式,结果表明:在误码率为10^-5时,该算法减少了约50%的编码辅助载波同步迭代次数;在含相位噪声的信号条件下,与理想解调译码相比,性能损失不超过0.15 dB。     

一种基于参数控制的低轨星载接收机载波跟踪算法CSCD

低轨星座接收机面临大多普勒频移及频繁快速换星等设计约束,对其载波跟踪环路设计提出了较高的动态适应性与跟踪精度要求。针对以上问题,提出了一种基于参数控制的载波跟踪算法。该算法引入环路控制因子参数,将环路滤波器分为牵引和跟踪两阶段。基于理论建模推导环路控制因子的最优参数配置原则,指导实现牵引和跟踪两种状态滤波器的协同配合,在牵引阶段有效引导大多普勒信号快速入锁,在跟踪阶段精确估计载波频移参数,实现基于低轨星载平台的GNSS信号快速准确跟踪。理论与仿真结果均表明基于参数控制的载波跟踪算法能够有效提升环路的动态适应性与跟踪精度,满足低轨星载接收机的设计需求。与传统算法相比,该算法在保证信号跟踪精度的同时,能够将收敛时间缩短78%,且环路设计简单,易于硬件实现。     

Cycle slip performance of digitally implemented phase detectors onAWGN channel

Cycle slip performance of digitally implemented phase detectors on additive white Gaussian noise (AWGN) channel is investigated. The performance measure evaluated is the mean cycle slip time of a first-order phase-locked loop. An equivalent phase detector model with state-dependent loop noise is employed. It is shown that this working basis is vital to arrive at correct results. Numerical results for triangular and saw-tooth type phase detectors are reported and compared with those for the multiplier phase detector     

《高频电子线路》课程“相乘器”教学策略

相乘器是高频电子线路课程中的一个重要单元电路。掌握相乘器的组成、基本原理、分析方法以及器件特点是通信电子信息类学生学好调制、检波以及混频电路的关键所在,讨论非线性器件二极管在开关状态下组成"相乘器"的教学策略对教学活动具有重要意义。     

相敏检波法在硬支承动平衡检测中的应用

为了检测硬支承情况下转子的不平衡量,针对目前常用相敏检波电路的缺点,提出了一种模拟乘法器式检测转子旋转过程中不平衡量大小和相位的相敏检波法。描述了此方法的原理,运用此方法设计了检测电路,实现了预期的目的。     

高动态下惯性加速度辅助三阶锁相环性能分析

针对高阶跟踪环路稳定性比低阶环路差,大带宽带来测量误差大的问题。研究在高动态环境下,惯导加速度信息辅助卫星接收机三阶载波锁相环跟踪算法,以及不同环路参数下跟踪环路的性能。对载体高动态场景、加速度信息延迟进行建模,并对算法进行了数学仿真。仿真分析结果表明,在加速度信息辅助下,即使压缩载波跟踪环路等效噪声带宽到3Hz,在高达1200g/s的加速度动态下,环路跟踪同样稳定可靠。     

Dynamics of the Phase-Locked Loop without a Limiter

The general (nth order) phase-locked loop is analyzed, of which the amplitude is not constant. The input carrier signal is amplitude-modulated by wide-band stationary Gaussian noise, and the signal, superposed with the additive white stationary Gaussian noise, enters the nonlimited phase-locked loop. Under the above assumptions the loop can be shown to constitute an n-dimensional vector Markov process, so that the process satisfies the n-dimensional Fokker-Plank equation. The probability density function depends on the effective loop signal-to-noise ratio and the effective modulation power.     

舰尾流环境中载机纵向QFT/TECS控制系统设计

为了消除舰尾流对载机着舰过程产生的影响,同时完成低动压状态下飞行速度与高度的解耦工作,基于定量反馈理论/总能量控制理论(QFT/TECS)设计了纵向着舰控制系统。针对着舰过程中数学模型所具有的不确定因素及舰尾流对下滑航迹的影响,以载机高度变化率为控制对象,使用定量反馈理论结合推力补偿系统进行了内回路鲁棒控制律设计。外回路控制律设计是以总能量控制理论为基础,通过粒子群优化算法对待调控制参数进行寻优,进而实现了对高度、速度等参数的精确控制,完成了载机纵向着舰轨迹与速度的解耦工作。仿真结果表明,该控制律在拥有较强的鲁棒性的基础上具有良好的解耦控制能力,实现了载机着舰段的高度与速度的解耦控制,明显提高了载机对着舰轨迹的跟踪能力,可满足不确定条件下载机的着舰要求。     

基于FPGA的硅微机械陀螺仪数字化驱动电路研究

为了进一步提高硅微机械陀螺仪的性能,提出了一种基于FPGA数字信号处理来实现控制的数字化驱动电路。该设计方案通过AGC环路稳定了驱动幅度,并用SPLL对相位进行了控制以跟踪谐振频率。两主要环路以FPGA为硬件基础,用软件编程实现,相较模拟驱动电路在实际应用中更具灵活性。实验给出了该电路的驱动幅度和频率漂移曲线,证明了该电路可以较好的实现硅微机械陀螺仪的驱动。     

轨道预测辅助GPS载波跟踪技术用于低轨道卫星定位研究

针对低轨道卫星及其特定的运动环境,研究了星载GPS接收机载波跟踪问题。基于卫星轨道可模化、可预测的特性,提出了利用预测卫星轨道计算多普勒频移,并用于辅助载波环路跟踪的新方法。该方法有效地降低了低轨道卫星GPS信号跟踪中的动态,从而在跟踪过程中可以采取降低环路阶数、减小环路带宽、增加预检测积分时间这几种措施来提高环路跟踪弱信号的能力,有助于提高低轨道卫星的定位性能。     

基于UKF准开环结构的高动态载波跟踪环路

 对高动态环境下的全球卫星导航系统（GNSS）载波信号跟踪方法进行了研究。在分析高动态载波信号模型的基础上,提出了一种基于无迹卡尔曼滤波（UKF）的准开环载波跟踪方法。此方法能够消除导航数据二进制相移键控(BPSK)调制的影响,并采用四维UKF相位估计模型提高跟踪精度,同时对估计值进行补偿以减少滤波器的滞后性。通过模拟接收机的高动态运动轨迹,从跟踪误差、跟踪结果和补偿效果3个方面,与基于卡尔曼滤波（KF）的锁频环(FLL)辅助锁相环(PLL)结构的传统跟踪方法进行比较,结果表明基于UKF的准开环跟踪方法能够有效地完成高动态环境下的载波跟踪。     

Phase-Shift-Keyed Signal Detection with Noisy Reference Signals

This paper derives and graphically illustrates the performance characteristics of Phase-Shift-Keyed communication systems where the receiver's phase reference is noisy and derived from the observed waveform by means of a narrow-band tracking filter (a phase-locked loop). In particular, two phase measurement methods are considered. One method requires the transmission of an auxiliary carrier (in practice, this signal is usually referred to as the sync subcarrier). This carrier is tracked at the receiver by means of a phase-locked loop, and the output of this loop is used as a reference signal for performing a coherent detection. The second method is self-synchronizing in that the reference signal is derived from the modulated data signal by means of a squaring-loop. The statistics (and their properties) of the differenced-correlator outputs are derived and graphically illustrated as a function of the signal-to-noise ratio existing in the tracking filter's loop bandwidth and the signal-to-noise ratio in the data channel. Conclusions of these results as well as design trends are presented.     

一种模块化航空有源滤波器的研究

 航空有源滤波器(AAPF)是解决飞机供电系统中电能质量问题的一种先进方案,而模块化设计对航空有源滤波器灵活性、可维护性和可靠性的提升作用巨大。首先提出并研究了一种新型模块化航空有源滤波器,分析了主电路数学模型及其混合载波PWM(CH-PWM)调制方式;其次基于损耗对比分析进行了主电路拓扑优化,推导了模块均压控制律并给出了系统控制策略;最后进行了仿真和实验验证。结果表明,模块化航空有源滤波器能够有效补偿航空电网中由典型非线性负载产生的谐波和无功电流分量,三相电网电流的总谐波畸变率(THD)均在5%以下,补偿效果显著。     

Performance analysis of GPS carrier phase observable

The accuracy analysis of Global Positioning System (GPS) carrier phase observable measured by a digital GPS receiver is presented. A digital phase-locked loop (DPLL) is modeled to extract the carrier phase of the received signal after a pseudorandom noise (PRN) code synchronization system despreads the received PRN coded signal. Based on phase noise characteristics of the input signal, the following performance of the first, second, and third-order DPLLs is analyzed mathematically: (1) loop stability and transient process; (2) steady-state probability density function (pdf), mean and variance of phase tracking error; (3) carrier phase acquisition performance; and (4) mean time to the first cycle-slipping. The theoretical analysis is verified by Monte Carlo computer simulations. The analysis of the dependency of the phase input noise and receiver design parameters provides with an important reference in designing the carrier phase synchronization system for high accuracy GPS positioning     

基于FPGA的北斗B1频点接收机 基带信号处理器设计

针对北斗二代B1频点信号比特翻转频繁的问题,设计并实现了基于FPGA的北斗B1频点导航接收机基带处理器.该处理器在信号捕获过程中设计了频率精细搜索的精捕获算法,避免了假捕获并且提高了捕获频率的精度;在载波跟踪环路中设计2阶锁频环辅助3阶锁相环的方案,以提高环路跟踪的动态性能.其中,锁频环和锁相环均设计了对比特翻转敏感的鉴别器,保证环路跟踪的准确性.试验结果表明,该基带处理器设计具有较高精度的捕获频率和良好的高动态跟踪能力.     

单载波干扰对星载扩频应答机码跟踪回路影响研究

扩频码同步是基于扩频体制卫星测控通信中的一项关键技术。研究单载波对星载扩频应答机中全时间超前-滞后非相干跟踪回路的影响,分析单载波干扰存在时跟踪抖动的恶化程度,给出相应的数学表达式,并进行了Matlab仿真。仿真结果表明：在一定的跟踪回路带宽下,恶化程度随着系统的扩频增益或频偏的增加而减小,并随着干信比的增加而增加。单载波干扰不变的前提下,恶化程度随着回路带宽的增加而增加。