维修动态

厦门太古向顺丰航空交付波音757客改货飞机
　　1月11日，厦门太古飞机工程有限公司向顺丰航空成功交付一架波音757-200客改货飞机，这也是厦门太古为顺丰航空完成改装的第7架波音757-200全货机。该货机采用美国Precision Aircraft Solution公司的改装方案，改装周期为90天。     

波音757客改货主货舱滑轨改装

简要介绍了波音757-200客改货中主货舱滑轨改装的主要工作内容及其在整个客改货的地位,阐述了改装过程中的关键点以及创新点,为之后改装工作所涉及各个专业工作的有序开展奠定了基础。     

维修动态

<正>国航成都基地首次向第三方客户交付波音757-200客改货飞机2014年12月26日,国航成都维修基地向顺丰航空交付了一架波音757-200客改货飞机,这是国航成都维修基地为第三方客户完成客改货重大改装工程的首架波音757飞机,标志着该基地的飞机重大改装能力获得了市场的认可。GAMECO完成首台CFM56-7B发动机反推翻修2014年12月9日,GAMECO首次完成了CFM56-7B发动机反推翻修工作。在此次维修中,GAMECO除了高质量地完成相关的服务通告(SB)工     

波音757客改货主货舱门区域改装

简要介绍了波音757-200型飞机客改货主货舱门改装的主要工作内容,以及工作中各种创新思维在关键技术难点上的应用,保证了整个主门区域改装工作的顺利完成,为今后其他类似大型改装或更高级别修理/改装积累宝贵经验。     

国航成都基地波音757-200PTF项目通过民航局科技成果鉴定

<正>2014年12月18日,在波音757-200飞机客改货科技项目成果鉴定会上,中国民用航空局认为国航成都维修基地的波音757-200客改货项目的成果达到了国际先进水平并同意通过鉴定。     

波音757客改货航电系统改装

简要介绍了波音757-200客改装货时航电系统改装的主要工作内容和改装工作中的关键点,以及为保证整体改装工作的进度而实施的的创新手段。     

浅析波音737-800客改货飞机冲压进气门的改装与修理

随着波音737-800飞机逐渐进入退役期,其客改货业务应运而生,客改货的工作主要是对结构进行改装和修理。本文结合客改货工作经验以及图纸手册,对波音737-800客改货飞机冲压进气门的改装与修理进行了总结,阐明了工作中的难点和误区,有利于提高改装工作的质量和效率。     

传承优秀回馈信赖

山东太古与波音签署737NG客改货合作协议
　　11月16日,山东太古飞机工程有限公司与波音公司在济南签署了合作协议,山东太古将成为新一代波音737-800改装货机（737-800BCF）项目的改装服务提供商。再加上该项目的另一改装服务提供商上海波音航空改装维修工程有限公司,目前波音737-800BCF项目在上海、山东两地共有三条改装生产线。波音737-800是首个波音提供客改货服务的新一代737机型。     

传承优秀 回馈信赖

正GAMECO完成其首架在国内注册的波音737-800改装货机4月26日,交银租赁与中国邮政航空在广州飞机维修工程有限公司(GAMECO)机库举行双方的"第一架波音737-800飞机客改货交付仪式",这是交银金融租赁与中国邮政航空交接的首架737-800波音改装货机(737-800BCF),也是GAMECO首次完成在中国民航局注册的737-800机型的客改货工作。客机改货机项目是一项工程庞大技术复杂的大型改装工作,其改装过程涉及专业面广,对各类资源保障要求高。本次改装历时三个多月,比原计划提前5天完工。     

以波音737-800BCF为例浅谈客改货飞机的关注点

疫情之下货运航空的快速发展,带来了客改货订单的显著增加,各公司纷纷推出不同的改装方案。本文从民航局现行规章入手,以波音737-800BCF为例,对客改货飞机接收过程中容易出现的问题进行了探讨,详细介绍了客改货机型的选择和波音公司的客改货改装方案,并对客改货施工过程中需关注的地方做了总结,可为航空公司顺利引进客改货飞机提供参考。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.