Noise Suppression Characteristics of a dc-to-dc Converter

Analytical and experimental considerations of the noise suppression characteristics of a typical dc-to-dc converter with a two-winding reactor are described. The high-frequency equivalent circuits for external noise are presented which are composed of parasitic parameters and have parallel and series resonances. The high-frequency responses calculated from these equivalent circuits agree well with the experimental results. Effects of the parasitic parameters on the noise suppression capability are discussed.     

Surge and Noise Generation in a Forward DC-to-DC Converter

Switching surge and noise voltages are analyzed under the common-mode condition in a forward dc-to-dc converter. The analysis is performed by partitioning the switching time into several states and introducing the high-frequency equivalent circuits. The equivalent circuits include not only inductive and capacitive parameters, but also the parameters related to the switching speed of the transistor and the recovery characteristics of the diode. As a result, the effects of these various parameters on the surge and noise generation are made clear quantitatively.     

A Design for Thick Film Microcircuit DC-to-DC Converter Electronics

The design concept for thick film microcircuit dc-to-dc converter electronics used in the power subsystem of the Thermoelectric Outer Planet Spacecraft is presented. Microcircuits have been used in low power logic circuits for nearly ten years, but only recently have these techniques been applied to power subsystem circuits which operate at higher power levels. Thick film microcircuit techniques have been utilized in a dc-to-dc converter reducing weight by 70 percent, volume by 80 percent, and interconnections by 75 percent. The close piece-part spacing allowed short interconnections and lower dissipation, and reduced noise coupling. The developed microcircuit handled total power levels from one watt to twenty-five watts.     

Zero dynamics-based design of damping networks for switching converters

A new design technique of the input filter damping network for dc-to-dc switching converters of buck type is presented. This technique is derived by means of zero dynamics analysis of the switching converter and yields equivalent results to those obtained using the classical approach based on minimizing the filter output impedance. The new method can be applied in converters of buck type with two inductors, boost with two inductors and dual SEPIC. Simulation and experimental results corresponding to a boost converter with two inductors illustrate the procedure.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Common-Mode Noise Generation in a DC-to-DC Converter

Analytical and experimental considerations of the common-mode noise in a dc-to-dc connverterare discussed. Analyzing the mechanism of the common-mode noise generation by means of a high-frequency equivalent circuit, we estimate the output noise voltage generated during the transistor's turn-on time. This commonmode noise consists mainly of two frequency components distributed in several megahertz. The effects of parasitic parameters on the noise voltage and frequencies are clarified. In addition, the effect of a common-mode choke on the noise suppression is discussed experimentally.     

Analysis and design of a three-phase LCC-type resonant converter

A three-phase dc-to-dc LCC-type resonant converter with high-frequency transformer isolation is proposed. The operation and a simple analysis of the converter are presented. Design curves are obtained and a design example is given. SPICE simulation and experimental results are presented to verify the performance of the proposed converter for varying load conditions. The converter proposed has several advantages, e.g., operation in lagging PF mode for the entire load range, requires a narrow variation required in switching frequency, reduced component size and stresses, etc     

A Pulsewidth-Modulated Dc-to-Dc Converter That Utilizes a Small Number of Components

In general, circuit reliability can be enhanced by either incorporating redundancy or by minimizing a circuits component count. Conventional nonregulating converters generally require two active devices, whereas in regulating converters or switching regulators as many as 10 transistors, either integrated or discrete, is not uncommon. A regulating dc-to-dc converter which provides useful regulation and which can be constructed with either two or three transistors is described.     

Start-Up Transient of a DC-to-DC Converter Powered by a Current-Limited Source

An analysis technique is presented which permits the designer to explore the start-up transient of a dc-to-dc converter when it is powered by a current-limited source. The current versus voltage characteristics of the source are superimposed upon those of the dc-to-dc converter. By noting the nature of the intersection of these curves in the voltage-current plane, we are able to predict whether or not the converter is able to start up while powering a specified load.     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

State Trajectories Used to Observe and Control DC-to-DC Converters

State-plane analysis techniques are employed to study the voltage stepup energy-storage dc-to-dc converter. Within this framework, an example converter operating under the influence of a constant on-time and a constant frequency controller is examined. Qualitative insight gained through this approach is used to develop a conceptual free-running control law for the voltage stepup converter which can achieve steady-state operation in one on/off cycle of control. Digital computer simulation data are presented to illustrate and verify the theoretical discussions presented.     

Quantization and Saturation Noise Due to Analog-to-Digital Conversion of Radar Returns from Targets with Log-Normal Radar Cross-Section Distributions

An analysis of the saturation and quantization noise generated by analog-to-digital (A/D) conversion of radar returns from targets with log-normal radar cross sections is presented. The results of the analysis show that the high-cross-section tails of the log-normal distribution require higher saturation levels to be set in the A/D converter. The setting of the higher saturation level in the converter results in an increase in quantization noise. Thus the minimum achievable distortion in the output of the A/D converter signal is considerably higher than that for radar targets if their radar cross section had an exponential power distribution.     

Pulse Synchronizing DC-to-DC Converter

The new dc-to-dc converter driven by the external pulse is presented. The principle is based on the synchronizing phenomenon in the transistor core multivibrator. There are the voltage feed- back in the OFF interval and the current feedback in the ON interval. The flux of the saturable core is changed along the minor hysteresis loop. The operations are explained by the aid of the averaged method of the state space technique. The efficiency of this converter is high and the construction is very simple.     

Noise Generation of a Switching Regulator

Analytical and experimental considerations on the surge and noise generated in a typical switching regulator are discussed. There are two kinds of surges which occur in the switching instants of the transistor. These surges appear as high voltages across the semiconductor elements and decrease their reliabilities. Corresponding to the surge generation, noise voltages appear in the output terminals and may induce malfunctions of a signal processing device connected to the regulator. We analyze these surge and noise voltages by means of high-frequency equivalent circuits.     

A State-Trajectory Control Law for DC-to-DC Converters

Mathematical representations of a state-plane switching boundary employed in a state-trajectory control law for dc-to-dc converters are derived. Several levels of approximation to the switching boundary equations are presented, together with an evaluation of the effects of nonideal operating characteristics of converter power stage components on the shape and location of the boundary and the behavior of a system controlled by it. Digital computer simulations ions of d-to-dc converters operating in conjunction with each of these levels of control are presented and evaluated with respect to changes in transient and steady-state performance.     

Table-Aided Design of the Energy-Storage Reactor in DC-to-DC Converters

A new procedure for the selection of magnetic cores for use in energy-storage dc-to-dc power converters that eliminates the need for an automated computer search algorithm and stored data file is presented. The converter configurations included in the procedure are the three commonly encountered single-winding converters for voltage stepup, for current stepup and voltage stepup/current stepup, and for the two-winding converter for voltage stepup/current stepup. For each converter configuration, three types of controllers are considered: constant-frequency, constant on-time, and constant off-time. Using concepts developed from analyses of these converters by considering the transfer of energy by means of an energystorage inductor or transformer, a special table of parameters calculated from magnetic core data is constructed, which leads to a considerably simplified design procedure.     

DC-to-DC Converter Power-Train Optimization for Maximum Efficiency

A new way is given to describe the independent and dependent design variables of the power train of a dc-to-dc converter in terms of a multidimensional design-parameter space. These concepts provide a framework for examining the problem of design optimization of the power train, with particular emphasis on the maximization of converter efficiency. Numerous examples of important parameterspace surfaces illustrate some of the major relationships between core volume, switching frequency, and output power and between efficiency, ripple, and temperature rise of the energy-storage reactor. Also, the difference in performance between the continuous and discontinuous magnetomotive (MMF) force modes of operation is explored.     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

Impulse Response Determination by Cross Correlation

This paper describes the design of a digital cross correlator and its application in determining the impulse response in linear systems. The output of the cross correlator, which correlates the input and the output of a linear system excited by noise, is the same as the response of the linear system to a pulse which is identical to the noise autocorrelation. The impulse response error is defined as the normalized mean-square deviation of the actual from the true impulse response. A digital computer simulation confirms that the conventional technique yields the same impulse error as the correlation technique, when the width of the input rectangular pulse is equivalent to the width of the noise autocorrelation function. The operation and design of the digital correlator are discussed. An advantage of the specially designed digital correlator over a general-purpose digital computer is to operate in real time without problems of software and storage. The presented experimental and digitally computed results show that the digital correlator can accurately determine the impulse response, even in presence of perturbations. Only the correlation technique allows measurement of system impulse response without disturbing normal operation. Suggestions are made to simplify the design and improve the speed (bandwidth capability).     

Charge equalization for an electric vehicle battery system

Charge equalization for series connected battery strings has important ramifications on battery life. It enhances the uniformity of the battery cells and hence improves the life of the battery as a whole. A new charge equalization technique for a series string of battery cells has been recently proposed by the authors. The basic technique utilizes a simple isolated dc-to-dc converter with a capacitive output filter along with a multiwinding transformer. The possibility of integrating the trickle charge function with the charge equalization function is potentially very attractive, as it can lead to an efficient and low cost implementation