结构非概率可靠性灵敏度分析方法

 结构非概率可靠性的灵敏度分析对工程中非概率问题的分析预测和优化具有重要的指导作用。基于结构非概率可靠性指标理论,提出了结构非概率可靠性的灵敏度分析方法。针对极限状态函数为线性的情况,推导出了非概率可靠性灵敏度的解析解。在此基础上,结合函数线性化理论,提出了求解极限状态函数为非线性情况的非概率可靠性灵敏度的近似解析方法。基于求解非概率可靠性指标的优化方法,并结合差分理论,提出了求解非概率可靠性灵敏度的优化方法。给出了算例分析,结果表明了所提方法的可行性。     

认知不确定性下可靠性灵敏度分析的新指标

传统的可靠性灵敏度指标只考虑了随机不确定性,当结构中还存在认知不确定性时,该指标难以反映出基本变量中认知不确定性对结构可靠性评估结果的影响程度.针对这一问题,引入概率包络来表达结构中的随机不确定性和认知不确定性,在此基础上建立了可靠性灵敏度分析的新指标——认知灵敏度系数,给出了其定义和代表的意义,并基于证据理论提出了认知灵敏度系数的计算方法.算例分析表明,认知灵敏度系数可以反映出基本变量中认知不确定性对结构可靠性评估结果的不确定性的影响程度,从而为有针对性地提高可靠性评估结果的准确性提供依据.另外,基于证据理论的认知灵敏度系数的计算方法适用于极限状态函数为单调、非单调的结构,以及变量服从正态、非正态的结构,具有普适性.     

变量相关情况下基于马尔可夫链样本模拟的线抽样可靠性灵敏度分析方法

针对变量具有相关性的可靠性灵敏度分析问题,提出了一种变量相关情况下基于马尔可夫链样本模拟的线抽样可靠性灵敏度分析方法。在所提方法中,首先将相关变量等价转换为独立正态变量,然后采用基于马尔可夫链样本模拟的线抽样方法,求解失效概率对等价独立正态变量分布参数的偏导数,最后利用等价变换前后变量分布参数之间的解析关系和复合函数求导法则,求得失效概率对相关变量分布参数的可靠性灵敏度。为了解所提方法的效率和精度,对所提方法的可靠性灵敏度估计值进行了方差分析。由于所提方法采用马尔可夫链快速产生失效域中的条件样本,这些失效域中的样本可用来准确获取重要方向,并可作为线抽样的随机样本,因而该方法具有很高的抽样效率。算例结果表明,所提方法是一种计算相关变量可靠性灵敏度的高效率、高精度方法。     

α-l型区间可靠性分析方法及其工程应用

在区间非概率可靠性模型的基础上,以区间长度l和区间下限α为结构系统变量的输入参数,重新定义了一种新的可靠性指标,分析得到了这种可靠性分析方法的判定依据;在此基础上,在线性和非线性条件下讨论了结构可靠度的计算方法.以某型飞机防冰引气管结构为例,进一步探讨了所提方法在共振可靠性分析当中的工程应用.     

考虑随机和认知混合不确定性的航空发动机燃烧效率灵敏度分析

针对燃烧室初步设计阶段输入参数存在混合不确定性的特点,提出一种概率盒框架下的全局灵敏度分析方法。简单介绍了航空发动机燃烧效率的一维计算方法;在随机和认知混合不确定性的概率盒表征基础上,使用Sobol指标的上下限表征概率盒中随机与认知混合不确定性对响应的贡献程度;最后基于双层嵌套蒙特卡洛/非嵌入式多项式混沌展开（Monte Carlo Simulation/Non-intrusive Polynomial Chaos Expansion,MCS/NIPCE）方法对概率盒灵敏度指标进行求解,筛选出重要变量和次要变量,实现模型的降维。通过某航空发动机燃烧效率的全局灵敏度分析对所提出的方法进行了验证。研究结果表明,Sobol指标的上下限可以显著表征概率盒灵敏度指标,在保证计算精度的前提下,双层MCS/NIPCE方法的计算效率要远远高于传统双层蒙特卡洛（Monte Carlo Simulation, MCS/MCS）方法,可获得考虑随机和认知混合不确定性情况下燃烧效率输入参数的重要性排序。     

基于截尾概率-非概率混合模型的可靠性优化算法

针对工程中截尾概率变量与非概率变量同时存在的情况,给出一种新的截尾概率与非概率混合可靠性模型。在该混合可靠性模型基础上,按照可靠性指标(RIA)法给出双层嵌套可靠性优化模型,并采用改进搜索策略后的ST-Powell优化算法在外层搜索设计变量的最优值,内层采用能保证收敛的改进的有限步长迭代法求解混合可靠性指标。数值算例表明,改进搜索策略后的ST-Powell优化算法的全局寻优性得到显著提升;改进搜索策略后的ST-Powell优化算法与改进的有限步长迭代法相结合求解双层嵌套混合可靠性优化模型的正确性得到验证,且对于非线性程度较高的极限状态函数同样能够得到满足截尾概率与非概率混合可靠性模型指标要求的最优解,并对工程结构算例具有很好的适应性。     

含有正态相关变量的多设计点/多失效模式情况下的方向抽样可靠性灵敏度分析

针对含有正态相关变量的多设计点/多失效模式系统的可靠性问题,提出了两种有效的基于方向抽样的可靠性灵敏度分析方法。可靠性灵敏度分析方法的基本思路是首先将正态相关变量进行等价独立标准正态变换,利用改进的方向抽样可靠性灵敏度分析方法得到独立标准正态空间的可靠性及灵敏度结果;通过复合求导法则,将独立标准正态空间的可靠性及灵敏度结果转化到正态相关空间,得到失效概率对相关正态变量分布参数(均值、标准差和相关系数)的偏导数,并对所推导的可靠性及灵敏度估计值进行了方差分析。与经典的MonteCarlo数字模拟法相比较,文中所列的数值算例和简单工程算例的分析结果验证了所提方法的可行性与有效性。     

相关变量模糊可靠性灵敏度分析的线抽样方法

 依据失效域具有模糊性时模糊失效概率的定义,提出了相关变量模糊可靠性灵敏度的分析方法。针对线性功能函数、正态基本变量和正态型隶属函数情况,推导了相关变量的模糊可靠性灵敏度计算的解析表达式。对于工程中的一般情况,给出了可靠性灵敏度分析的数字模拟方法。尽管数字模拟法适用范围广,但该方法的效率较低,尤其是针对高维和小失效概率问题。为了解决数字模拟方法效率低的问题,提出了相关变量模糊可靠性灵敏度分析的线抽样方法。通过离散模糊失效概率积分区域,建立了相关变量模糊可靠性灵敏度与离散区域随机可靠性灵敏度的关系,进而可以利用相关变量随机可靠性灵敏度分析的线抽样方法求得模糊可靠性灵敏度。相关变量模糊可靠性灵敏度分析线抽样方法的基本原理、计算公式及实现步骤被详细给出,文中算例充分验证了其精度高、收敛快及适用于高维和小失效概率等优点。     

可靠性灵敏度分析的一种新方法

基于极限状态函数矩估计的失效概率计算,提出一种新的可靠性灵敏度分析方法。推导极限状态函数的矩对基本变量分布参数的偏导数,并进而利用失效概率与极限状态方程矩的关系,推导失效概率对基本变量分布参数的偏导数,从而得到可靠性灵敏度。与改进一次二阶矩可靠性灵敏度分析方法相比,所提方法不用求极限状态方程的设计点,因而不需用到极限状态函数对基本变量的梯度函数,适用于隐式极限状态方程的可靠性灵敏度分析,算例结果也充分显示所提方法的合理性和精度。     

基于RBF和主动学习的非概率可靠度求解方法

进行结构非概率可靠性分析时，对于失效域与超椭球不确定域发生干涉的情况，非概率可靠度相较于非概率可靠度指标更具有适用性。为了提高超椭球模型下结构非概率可靠度的求解效率，本文提出一种求解非概率可靠度问题的高效主动学习方法。首先，结合交叉验证和jackknifing方法推导了RBF模型在未知点处的jackknifing方差以评估模型预测的不确定性，并根据该方差基于RBF的主动学习函数对非概率可靠度进行求解。其次，提出有效收敛准则来终止非概率可靠性分析的主动学习过程。最后，3个算例表明该方法能够在较少功能函数调用次数下得到精确的非概率可靠度估计值，具有良好的工程应用价值。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.