联合压缩感知与接收分集的DME干扰抑制方法

针对L波段数字航空通信系统(L-DACS1)反向链路测距仪(DME)信号干扰正交频分复用(OFDM)接收机的问题,提出基于联合压缩感知与接收分集的干扰抑制方法。在地面基站各接收支路中,首先通过压缩感知重构DME干扰信号,随后将重构的DME信号在时域进行干扰消除,消除干扰后各支路信号最终通过最大比值合并提高OFDM解调器输出信噪比,以克服测距仪残留信号的影响。仿真结果表明:该方法可有效抑制DME信号的干扰,提高L-DACS1系统的可靠性。     

一种基于多基线载波相位差测量的欺骗干扰检测方法

由于卫星导航信号到达地面的信号功率较低,且民用部分信息公开,极易受到欺骗干扰信号的影响,从而导致接收机解算出错误的位置、速度或时间.针对传统的欺骗干扰检测与抑制方法不能对欺骗干扰进行测向的问题,提出了一种基于阵列多天线接收信号的载波相位差进行欺骗信号检测与抑制的方法.该方法能够在缺少先验知识的条件下,借鉴相关干涉仪测向...     

非合作无源探测中的假设检验弱目标检测方法

在非合作无源探测系统中,弱目标回波不仅会受到强直达波、强多径的干扰,还会受到强目标的掩盖干扰,因此很难对其进行有效检测。为了解决这一问题,提出了一种基于多择复合假设检验的弱目标检测方法。首先将接收信号投影到多径干扰的正交补子空间内,以消除强直达波和强多径干扰,然后将目标检测看作一个多择复合假设检验问题,建立了与之相应的基本框架模型,利用最大后验估计方法对目标时延、多普勒频移及信号幅度等参数进行估计,构造检验统计量,设置相应的门限,根据假设检验结果,逐个消除强目标干扰从而达到检测弱目标的目的。仿真结果表明,本方法可以有效抑制强直达波、强多径及强目标干扰,有效检测出弱目标,且虚警率低。     

一种高动态低信噪比下载波快速捕获跟踪方法

针对高动态、低信噪比的接收信号,首先对整个多普勒频率范围进行分段,并在每一段内利用本地产生的带有多普勒频率变化率的复信号来抵消接收信号中多普勒频率变化率的影响,然后在每一段内利用FFT（FastFourierTransform,快速傅里叶变换）进行载波频率并行捕获,从而同时完成载波多普勒频率及其变化率的初步估计。利用载波多普勒频率及其变化率估计信息辅助锁频环快速入锁,进而利用锁频环辅助三阶锁相环完成载波信号的锁频锁相跟踪。使用这种方法,可以快速获取信号的多普勒频率及其变化率信息,并且在极短时间内完成载波的稳定跟踪,使接收设备具备快速捕获跟踪大动态弱信号的能力。     

一种利用功率反演和线性约束最小方差算法的自适应天线

介绍了一种新的基于功率反演和线性约束最小方差的算法,以高度抑制GPS接收机的干扰信号。这种结构通过提调整天线阵列的权值,实时地接收并改变来自各方向的GPS信号,同时对不同方向的干扰信号有高的抑制比。对固定和移动的干扰都做了仿真,仿真表明这种结构有很深的零点,对固定干扰信号的抑制比可达到115dB,对移动干扰信号的抑制比可达到94dB。     

基于扩展单脉冲比的拖曳式诱饵存在性检测

诱饵的存在性检测是对抗拖曳式有源雷达诱饵干扰的前提,也是决定抗干扰效果的重要因素.当导引头雷达发射多个不同频率的脉冲信号时,在一定的检测处理时长内目标回波信号幅度服从瑞利分布,而诱饵干扰信号则是幅度固定的.基于导引头雷达波束内诱饵存在导致的回波特征变化,通过提取诱饵存在/不存在两种情况下雷达接收回波信号的幅度特征差异以...     

基于PNFM-LFM复合调制的探测干扰共享波形设计

针对雷达-电子战一体化共享信号波形的设计需求,提出一种伪码噪声调频与线性调频复合调制的探测干扰共享波形。在伪码序列的伪随机性和规律性上,通过理论推导和仿真实验,分析并验证了该探测干扰共享波形具有良好的模糊函数以及线性可控的频谱特征,有效通带内干扰功率利用率平均可达38%;通过探测干扰共享信号的相关信号处理,本地接收机能够成功地对信噪比不低于-27 dB的回波信号进行检测,且改善因子可达30 dB。     

变换域通信系统及其关键技术

变换域通信系统通过信道估计在变换域设计信号波形避开干扰,它没有采用载波调制,而是用一个类似噪声的基函数进行信息调制。论述了变换域通信系统的基本概念,对变换域通信系统的关键技术——环境干扰估计与检测、基函数序列与波形设计、调制解调与高速率数据传输进行了分析,最后指出了其应用前景。     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

基于小波变换的测距仪脉冲干扰抑制方法

为解决L频段数字航空通信系统以内嵌方式部署在L频段测距仪频道间而产生的测距仪系统干扰宽带航空数据链接收机的问题,基于小波变换去噪方法提出L-DACS1系统测距仪脉冲干扰抑制接收机,利用LDACS1及测距仪脉冲干扰信号特性,基于小波变换去噪方法重构测距仪脉冲信号,然后在时域内消除测距仪脉冲干扰信号。计算机仿真结果显示:在高斯白噪声信道与多径信道环境下,所提出L-DACS1接收机方案可有限消除测距仪脉冲干扰,提高链路传输的可靠性。     

Results from a Four-Element Adaptive Antenna Experiment

Experimental results from a four-element, linear, half-wavelength spacing, adaptive-array antenna under the control of the least mean square (LMS) algorithm are presented. The array is found to be capable of nulling a 70-MHz signal to -35 dB below a desired signal over a 5-MHz bandwidth. The antenna processing gain is constant over a desired signal-to-jammer signal power ratio range from -20 dB to 5 dB. A sharp reduction in processing gain is observed for angular separations between jammer and desired signal of less than 10°. Antenna patterns taken with weights set in 300 iterations of the LMS algorithm show that the one strong, one weak jammer combination has a longer weight convergence time and reduced processing gain compared with a two strong jammers combination. Contours of constant desired signal-to-jammer signal power ratio, after adaptive antenna processing, reveal a complex shape for communication between air and ground due to the finite angular resolution of the adaptive antenna.     

Effects of CW Interference on Narrow-Band Second-Order Phase-Lock Loops

This paper describes an experimental study of the effect of continuous wave (CW) interference and white noise on a second-order phase-lock loop. The reciprocal of the loop mean-square phase error is used as an index of performance, and the effect of interference levels that do not cause cycle skipping or loss of lock is described in terms of this index. Loop thresholds are determined by measurement of cycle-skipping rates. Stationary or slowly-sweeping CW interference caused a degradation in loop threshold of roughly 3 dB for every 6 dB of interference power above the noise power level. The effective loop signal-to-noise ratio was decreased approximately 1 dB at interference-to-noise power ratios of -3 dB. Interference levels equal to the signal level consistently caused loss of lock, regardless of the loop signal-to-noise ratio.     

Adaptive Array Behavior with Sinusoidal Envelope Modulated Interference

The behavior of a LMS (least mean square) adaptive array with modulated interference is described. An interference signal with sinusoidal, double-sideband, suppressed-carrier modulation is assumed. It is shown that such interference causes the array to modulate the desired signal envelope but not its phase. The amount of the desired signal modulation is determined as a function of signal arrival angles and powers and the modulation frequency of the interference. Such interference also causes the array output signal-to-interference-plus-noise ratio (SINR) to vary with time. However, it is shown that when the desired signal is a digital communication signal, the averaged bit error probability is essentially the same as for continuous wave (CW) interference.     

Mismatched Filtering of Sonar Signals

A replica correlator (matched filter) is an optimum processor for a receiver employing a pulse of continuous wave (CW) signal in a white Gaussian noise background. In an active sonar, however, when the target of interest has low Doppler shift and is embedded in a high reverberation background, this is not so. High sidelobes of the correlator frequency response pass a significant portion of the signal contained in the mainlobe of the reverberation spectrum. In order to reduce the sidelobes of the correlator output spectrum and at the same time keep the increase in its 3 dB bandwidth to a small amount, we propose lengthening of the replica of the transmitted signal and weighting it by a Kaiser window. It is demonstrated that by extending the weighted replica by 50 percent compared with the transmitted signal, it is possible to reduce the sidelobe levels to at least 40 dB below the mainlobe peak, with the concomitant increase of the 3 dB band-width by less than 5 percent. The degradation in signal-to-noise ratio (SNR) performance for such a ?mismatched? filter receiver with respect to the matched filter is less than 1.5 dB.     

Imperfect Carrier Recovery Effect on Filtered PSK Signals

Coherent demodulation of a PSK signal requires the generation of a local carrier phase reference. Methods are given to determine the detection loss caused by noisy phase recovery and its use in the coherent detection of filtered BPSK and QPSK signals. It is assumed that the phase noise can have a static part and a random component with a Tikhonov-type distribution. The static part is mostly due to offset frequency tracking of the PLL used to recover the carrier, while the random component is due to thermal noise present in the carrier recovery loop and is also due to the random nature of the phase modulation. It is shown that the probability of error of BPSK and QPSK can be expressed as a finite sum of a set of strictly alternating converging series when the number of ISI terms is finite. Upper and lower bounds on the probability of error have been derived when this number becomes infinite and we show how this error rate can be computed with any desired accuracy. Numerical results are presented for various values of static error and phase noise variance when the transmit and receive filters are 4-pole Butterworth filters. For filtered PSK signals and for a bit error rate of 10-6, our results show that the additional degradation in presentday receiver systems due to imperfect carrier recovery can be less than 0.1 dB for BPSK and less than 1 dB for QPSK.     

基于ICA包络增强MEMD的滚动轴承故障诊断

针对多元经验模态分解(MEMD)存在模态混叠、带内噪声干扰导致轴承故障特征信息微弱难提取问题,提出了基于独立分量分析(ICA)包络增强MEMD的滚动轴承故障诊断.采用MEMD对多通道信号进行自适应分解,依据峭度和相关系数选取包含故障信息的本征模态函数(1MF);对所选取IMF分量的包络信号进行ICA分析,抑制模态混叠和...     

The Effect of a Pulsed Interference Signal on an Adaptive Array

The performance of a least mean square (LMS) adaptive array in the presence of a pulsed interference signal is examined. It is shown that a pulsed interference signal has two effects. First, it causes the array to modulate the desired signal envelope (but not its phase). Second, it causes the array output signal-to-interferenceplus-noise ratio (SINR) to vary with time. The desired signal modulation is evaluated as a function of signal arrival angles, powers and interference pulse-repetition frequency (PRF) and pulsewidth. It is shown that the signal modulation is small except when the interference arrives close to the desired signal. To evaluate the effect of the time-varying SINR, it is assumed that the array is used in a differential phase-shift keyed (DPSK) communication system. It is shown that the SINR variation causes a noticeable but not disastrous increase in the bit error probability.     

Limiter Intermodulation Improvement Due to Selective Carrier Spacing

In many space communications applications, the intermodulation between carriers, due to limiting in a common amplifier, reduces the overall signal-to-noise ratio of the signal received at the ground station. By selectively spacing the carriers, one is often able to avoid the strong or low-order intermodulation. The question arises how much improvement is gained in carrier-to-interference ratio and signal-to-interference ratio by selectively spacing carriers such that low-order cross products are avoided or their impact is effectively reduced. The following analysis investigates interference improvement due to selective carrier spacing for several spacing sequences relative to equal carrier spacing. It is shown that the intermodulation noise reduction depends on the carrier packing density of the selected spacing sequence. The carrier-to-intermodulation noise ratio increases with the number of participating carriers, while the bandwidth efficiency decreases. The signal-to-intermodulation noise ratio improves not only because of the improved carrier-to-intermodulation noise ratio, but also because the remaining interference components have spectra with larger frequency spreading.     

Null phase-shift polarization filtering for high-frequency radar

In order to effectively cancel the interference in polarization filtering, the parameters of the polarization filter should timely adapt to the variation of the polarization of the interference, which may impact the amplitude and phase of the desired signal that passes through the same polarization filter during the coherent integration time (CIT) and render the enhancement of the signal integration a failure. To avoid this, a null phase-shift polarization (NPSP) filter is proposed, which is composed of a linear polarization transformer (LPVT), a conventional single-notch polarization (SNP) filter and an amplitude/phase compensation device (A/PCD). The interference, which has polarization different from those of the desired target signal, can be suppressed completely while the target signal remains without distortion. Some applications of high-frequency (HF) radars for suppressing the radio interference are introduced. Simulation results from the experimentally derived data indicate that the improvement of the signal-to-interference ratio (SIR) can be expected to be more than 28 dB. The proposed NPSP filter is effective in HF radar or other coherent systems.