运输类飞机平尾失速敏感性及其试飞技术研究

从平尾失速理论研究出发,探讨了可能产生平尾失速的飞行状态,总结了可用于运输类飞机平尾失速敏感性研究的飞行试验技术,研究了平尾失速和机翼失速的相互区别,帮助飞行员在遇到机翼失速或平尾失速时进行必要的清晰判断,并采取适当的改出方法,从而保证飞机飞行安全.研究结果可为未来大型运输类飞机平尾失速敏感性试飞提供很好的技术支持.     

Y-8飞机平尾积冰导致的飞行事故分析

平尾积冰对飞行安全影响重大.通过介绍连续两起平尾积冰导致的Y-8飞机飞行事故,分析了飞机结冰的气象条件,平尾积冰和放襟翼对平尾气动特性的影响,以及平尾积冰失速的改出方法和预防措施.     

某型尾吊高平尾飞机失速特性试飞方法研究

某型尾吊高平尾飞机通过安装失速保护系统改善失速特性,满足了适航条例的要求。介绍了失速保护系统的设计,从保障试飞安全的失速试飞准备工作、失速保护系统研制试飞与失速特性验证试飞三个方面研究了安装失速保护系统飞机的失速试飞方法。     

平尾结冰对飞机动力学特性影响的仿真研究

针对某型飞机平尾结冰后的动态响应问题,利用结冰参数建立的平尾结冰参量模型,仿真分析了无操纵情况下平尾结冰对巡航特性的影响,以及平尾结冰后升降舵单位阶跃的纵向操纵响应,并研究了不同平尾结冰严重程度下飞机在进近与着陆过程中的动态响应及平尾失速特性,获得了平尾结冰对飞机动力学特性的影响规律.     

高平尾布局飞机深失速特性及失速改出伞数值计算与分析

ARJ21飞机是我国自行研制的具有典型T尾布局特点的先进支线飞机。失速和失速特性试飞是ARJ21飞机适航取证试飞最重要的试飞项目之一。高平尾(T尾)布局飞机可能存在深失速运动模态,给飞机的失速特性试飞带来安全风险。本文首先分析了高平尾(T尾)布局飞机的空气动力学特点,剖析了"深失速"现象的产生原因,并在此基础上以ARJ21飞机为算例,结合具体的风洞实验数据库,应用工程估算的方法对动导数进行了补充完善,其次建立了适合预测飞机失速和深失速运动方程的空气动力学模型,并对飞机的运动特性特别是深失速特性进行了仿真计算,计算结果与实际试飞结果取得了较好的一致性;最后选择深失速状态作为失速改出伞设计的临界状态,建立失速改出伞的数学模型,对失速改出伞改出深失速的动态过程进行了仿真计算,验证了失速改出伞改出深失速的设计参数,为失速改出伞的研制提供了参考依据。     

JL8飞机失速尾旋飞行试验研究

叙述了JL8飞机失速尾旋试飞状态、试飞试验和试飞结果。试飞结果表明，JL8飞机具有良好的大迎角特性及低速和高速失速特性。其正飞尾旋获得了三种模态，即“落叶飘”型非定常尾旋、非定常陡振荡尾旋和左均匀平尾旋；倒飞尾旋呈不稳定型态。而且各种尾旋都能成功地改出。另外，还评价了误操纵对失速和尾旋的影响。可供飞机大迎角和失速、尾旋特性研究人员参考。     

飞机积冰后若干飞行力学问题综述

回顾飞机积冰后若干飞行力学问题研究的历史与现状,着重介绍了积冰飞机气动数据的获取途径、积冰飞机飞行力学建模与飞行仿真、积冰对飞机稳定性和操纵性的影响以及积冰对飞机飞行性能的影响.在已有飞机积冰后飞行力学问题研究的基础上,提出了飞机积冰后飞行力学问题研究领域需要解决和关注的若干问题,包括通过数值模拟方法获取积冰飞机的气动数据、完善积冰对飞机气动导数影响的计算模型以及加强平尾失速方面的研究.今后需要进一步对模拟冰风洞、数值模拟方法和平尾失速进行研究,并获取更多实验数据.     

一种平尾涡流发生器设计和流动控制研究

平尾的气动特性直接影响飞机的飞行安全,基于改善飞机平尾在负攻角下流动特性的应用需求,设计一种涡流发生器,安装在平尾下表面。通过数值模拟方法研究平尾在不安装涡流发生器和安装涡流发生器两种构型下的流动特征和机理,分析飞机在负攻角下的俯仰力矩特性。结果表明：安装涡流发生器的平尾负失速迎角推迟了4°,负攻角下的俯仰力矩拐点推迟了4°左右,拓宽了飞机的飞行边界。     

俯仰姿态保持模式下飞机结冰边界保护方法

在研究飞机结冰机翼和平尾失速机理的基础上,以飞机迎角作为关键参数,飞机俯仰指令作为指令参数,提出一种基于飞机自驾仪的结冰后边界保护方法.通过引入铰链力矩检测模块,提前告警飞机失速,为边界保护提供了裕度.建立飞机纵向动力学方程,针对俯仰姿态保持（PAH）模式下机翼失速进行了仿真计算.结果表明:结冰条件下,通过铰链力矩的检测,飞机能在失速迎角为2°之前,进入边界保护模式,增加飞行安全的裕度.通过控制指令的限制,自动驾驶模式下飞机迎角能保持在失速迎角之内.      

民用飞机失速特性研究

民用飞机失速特性和失稳特性的优劣直接影响飞机的安全性。从平尾修形、外侧缝翼缝道参数、内侧缝翼分离面等几个方面考虑,深入研究了失速特性和失稳特性的影响因素。本研究结果,为一般民用飞机失速特性设计提供切实有效的措施。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.