C/H/O/N/B体系气相燃烧化学动力学模型及计算研究

为了更加深入地研究硼粒子的点火和燃烧机理,在Pasternkck和Zhou的模型的基础上,通过补充基元反应和修正基元反应的动力学参数,建立起了新的C/H/O/N/B体系气相燃烧动力学模型,该模型包含31种组分,190个正反基元反应。采用新的模型对贫氧体系气相燃烧过程进行计算,并改变体系的初始温度及压强,研究其对平衡温度和硼的氧化物平衡摩尔分数的影响。计算结果表明:(1)体系平衡后硼元素主要以硼的氧化物形式存在,其中BO和BO₂的摩尔分数随反应时间的增加先升高后降低,B₂O₃的摩尔分数随着反应时间的增加而不断升高。(2)提高初始温度和压强不但能使体系的平衡温度提高,而且能缩短体系达到平衡的时间。(3)提高初始温度会使B₂O₃更多地解离为BO和BO₂,不利于硼燃料能量的完全释放,但提高压强会抵制B₂O₃的解离,从而会在一定程度上提高硼燃料的能量释放。      

天然气氧化特性的实验与数值计算

在流动管反应器中对压力为0.1 MPa、温度范围为500~1 850 K、当量比分别为0.5、1.0与3.5的工况条件下天然气（90%甲烷/7%乙烷/3%丙烷，体积分数）的氧化过程进行了实验测试。同时，通过全局敏感性分析方法，构建了天然气的简化反应动力学机理（38组分和149反应），并对天然气的氧化特性进行了数值计算。结果表明：随着当量比增大，燃料发生氧化反应的起始温度与终止温度逐渐升高，CO生成与消耗完全对应的反应温度逐渐升高，NO的生成量逐渐降低。天然气的简化反应机理可以很好地预测天然气氧化过程中主要组分摩尔分数随温度变化的整体趋势；但是在C₃H₈、C₂H₂、NO、NO₂的起始反应温度或摩尔分数峰值的预测上与相应实验值存在差异。     

g-C3N4/Fe2O3复合催化剂的表征及其对AP的催化作用

为了改善固体推进剂中高氯酸铵（AP）热分解性能,降低其热分解温度,利用SEM,XRD,FT-IR对原位制备的g-C₃N₄/Fe₂O₃复合催化剂的形貌和结构进行了表征,通过差示扫描量热法（DSC）考察了催化剂对AP 热分解的催化效果。结果表明：g-C₃N₄/Fe₂O₃复合结构完整,Fe₂O₃颗粒紧密负载在g-C₃N₄上;加入不同质量分数的复合催化剂,AP的低温分解峰和高温分解峰都明显降低,且随着催化剂加入量的增加催化效果增强;加入复合催化剂质量分数5%时,高温分解峰和低温分解峰分别降低到348.1℃和281.7℃,表明g-C₃N₄/Fe₂O₃复合催化剂可有效降低AP的热分解温度,改善其热分解性能。     

利用遗传算法和LMI设计固定结构H2/H∞飞行控制律

 在设计飞翼式无人机(UAV)的横航向飞行控制系统时,为了使无人机具有较好的动态特性和阵风抑制能力,同时又便于工程实现,提出了固定结构的H₂/H_∞控制律设计方法。对于由此遇到的双线性矩阵不等式(BMI)问题,先用线性矩阵不等式(LMI)方法得到控制律参数和H₂/H_∞性能指标的映射关系,再用此映射关系作为适应度函数,用改进的遗传算法求解使H₂/H_∞性能最优的控制律参数。仿真结果表明,使用固定结构的H₂/H_∞控制方法的无人机动态响应迅速平滑,在侧风干扰下的滚转角振荡幅值仅是原经典控制方法的一半。     

非平衡等离子体对甲烷点火和火焰传播影响的机理分析

为了探讨非平衡等离子体对甲烷点火和火焰传播速度影响,采用化学动力学模型GRI-Mech3.0,利用零维、均质、完全混合模型和火焰传播速度模型,对甲烷点火过程和火焰传播过程进行数值模拟,计算得到了非平衡等离子体生成自由基(O自由基和NOX自由基)对甲烷点火延迟时间和火焰传播速度的影响规律。结果表明:当分别加入0.5% O和0.5% NOX活性基时,点火延迟时间减少了约94.7%,63.1%(加入NO)和94.2%(加入NO₂)。通过反应路径分析和敏感度分析,揭示了非平衡等离子体生成自由基影响甲烷点火和火焰传播速度的化学反应机理。      

双损耗Al2O3基多孔吸波材料的制备及其吸波性能

基于片状Al₂O₃陶瓷互锁结构强度高的特点,制备出夹杂石墨的高气孔率的Al₂O₃多孔陶瓷,并通过原位还原在多孔骨架中制备出Ni微粒,形成一种轻质的双损耗陶瓷基吸波材料。通过XRD、FE-SEM和EDS研究了还原温度对多孔吸波材料的组成、微观形貌、元素分布和吸波性能的影响。结果表明,还原温度升温至700 ℃可将多孔网络中Ni完全还原,形成以堆叠互锁Al₂O₃为基,夹杂片状石墨和孔表面覆盖Ni微粒的双损耗轻质吸波材料。当复合材料厚度为6.5 mm时,最小反射损耗为-35.01 dB,有效吸收带宽达到1.75 GHz。片状Al₂O₃锁定的石墨片构筑的导电网络,Ni微粒与基体之间的极化效应等共同促进复合材料良好的微波吸收性能。     

超燃冲压发动机燃烧室出口温度场分布CARS测量

针对超燃冲压发动机研究中对燃烧室出口温度场的测量需求以及暂冲式超燃冲压发动机燃烧台架试验中的应用难点,开发了适用于瞬态燃烧场温度测量的单脉冲相干反斯托克斯拉曼反射（CARS）系统及CARS光谱计算和温度反演软件CARSCF。采用USED相位匹配方式来降低湍流影响,结合多尺度小波分析方法来实现CARS光谱降噪处理,提高信噪比。在暂冲式脉冲燃烧风洞上开展了来流马赫数2.6条件下超燃冲压发动机燃烧室出口温度测量试验,获取了超声速来流（冷态）建立、H₂点火加热空气、建立超声速燃烧流场直至试验结束过程中的燃烧室出口温度,以及煤油/空气燃烧时燃烧室出口温度场分布。结果显示,超声速冷流时温度处于低温（约205K）状态,随着H₂点火加热来流空气,来流温度上升至853K;随着煤油/Air点火,温度急剧上升,稳定燃烧状态下燃烧流场温度为1970K±144K。燃烧室出口截面温度场分布测量结果显示,高温区位于燃烧室出口截面上侧区域,而燃烧室出口截面上中间区域的温度低于上下两侧。燃烧室出口温度分布CARS测量结果与火焰自发光成像结果一致,表明单脉冲CARS技术用于瞬态燃烧流场温度测量的可行性。     

挠性多体系统的一般动力学模型

 考虑n个互相连结的空间树形挠性多体系统,不妨按照Ho的直接路思想对系统分层标号,并选取体1为系统的主体,所有直接路均是相对体1而言的。如图1所示,选取O_Ex_By_Ez_B为地心惯性系,而O₀为整个系统的质心,O₀x₀y₀z₀为参考坐标系,系O₁x₁y₁z₁固连在主体1上,而系O_iX_iy_iZ_i（2≤i≤n）的原点在体i与其直接内连体的铰结点处,并固连在体i上,铰链点O_i允许有三自由度平动和三自由度转动,为了方便,也将O₀和O₁点看作两个虚设的铰链点。     

用有机硅树脂YR3370连接RBSiC陶瓷

 以一种聚硅氧烷类有机硅树脂YR3370(GE Toshiba Silicones)为连接剂,连接了反应烧结SiC(RBSiC)陶瓷。连接件在1 100~1 300℃的99.99%N₂气流中进行热处理。用三点弯曲强度实验测定连接件的强度,用场发射扫描电镜、X射线衍射和热重测试分析显微结构和化学反应。在连接温度为1 200 ℃时,连接件的三点弯曲强度达到最大值197 MPa。连接层是由有机硅树脂YR3370裂解生成的无定形Si_xO_yC_z陶瓷,其结构连续均匀致密,厚度在2~5 μm之间。连接机理是通过无定形Si_xO_yC_z陶瓷的无机粘接作用在RBSiC陶瓷基体和连接层之间形成连续的化学键。     

碳纤维和石墨纤维增强铝复合材料界面反应与性能的关系

 研究了碳纤维和石墨纤维增强纯铝复合丝的界面反应产物A1₄C₃的量与温度、复合丝的室温拉伸强度与A1₄C₃量及温度的关系。对各类复合丝的断口形貌进行了扫描电镜分析,对应于不同的热暴露温度及强度有三种断口特征。用盐酸溶液脱去了经不同温度热暴露后复合丝中的铝基体,分析了脱铝纤维的表面形貌,测定了拉伸强度,得到了复合丝中纤维受到损伤的温度范围。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.