基于视觉的大尺度部件相对位姿实时测量方法研究

相对位姿是装配过程中的一项重要监控项。针对大尺度部件对接过程中的相对位姿测量需求,提出了一种基于视觉的相对位姿实时测量方法。该方法利用单目视觉技术,通过采集合作靶标的图像,实时解算大部段间的相对位姿,用于辅助大尺度部件的装配。首先,设计了一套相对位姿实时测量系统,包括搭载单目相机的视觉测量单元,以及用于辅助位姿解算的合作靶标;其次,对相对位姿测量的完整流程进行了研究,包含系统标定方法与实时位姿解算方法;最后,在实验室环境下对位姿测量系统的精度进行测试。试验结果表明,位姿测量系统在垂直于光轴方向的重复精度可达0.02mm,沿光轴方向重复精度优于0.2mm,输出位姿结果时间低于0.3s;对多测量单元组网测量进行了仿真计算,垂直于光轴方向的重复精度优于0.1mm,沿光轴方向重复精度优于0.2mm,输出位姿结果时间优于1.3s。试验结果表明,提出的方法可满足一般大尺度部件对接过程实时位姿监控与对接状态评估的需求。     

Algorithm and experiments of six-dimensional force/torque dynamic measurements based on a Stewart platform

Stewart platform (SP) is a promising choice for large component alignment, and interac-tive force measurements are a novel and significant approach for high-precision assemblies. The designed position and orientation (P&O) adjusting platform, based on an SP for force/torque-driven (F/T-driven) alignment, can dynamically measure interactive forces. This paper presents an analytical algorithm of measuring six-dimensional F/T based on the screw theory for accurate determination of external forces during alignment. Dynamic gravity deviations were taken into con-sideration and a compensation model was developed. The P&O number was optimized as well. Given the specific appearance of repeated six-dimensional F/T measurements, an approximate cone shape was used for spatial precision analysis. The magnitudes and directions of measured F/Ts can be evaluated by a set of standards, in terms of accuracy and repeatability. Experiments were also performed using a known applied load, and the proposed analytical algorithm was able to accu-rately predict the F/T. A comparison between precision analysis experiments with or without assem-bly fixtures was performed. Experimental results show that the measurement accuracy varies under different P&O sets and higher loads lead to poorer accuracy of dynamic gravity compensation. In addition, the preferable operation range has been discussed for high-precision assemblies with smal-ler deviations.     

基于关键装配特性的大型零部件最佳装配位姿多目标优化算法

为了控制装配过程中的关键装配特性,以大尺寸测量技术为辅助,实现大型零部件最优位姿装配,提出基于关键装配特性的大型零部件最佳装配位姿多目标优化算法。该方法将测量辅助装配(MAA)中的关键环节——最佳装配位姿拟合问题分为两步:第1步利用基于奇异值分解的解析方法将测量坐标系与装配现场的全局坐标系进行精确的空间配准,减小了坐标系对齐的误差,并以参考点拟合的偏差为优化目标,求解移动装配体当前位姿;第2步根据装配关键特性相关公差的重要程度,计算装配综合精度要求,并以最小综合偏差为优化目标求解移动装配体间的最佳装配位姿。随后给出了上述两个步骤的粒子群优化算法模型,将每步的待求解位姿作为一个拥有3个旋转自由度与3个平移自由度的粒子进行求解。最后对卫星舱段位姿最优装配问题进行仿真计算,结果证明了该优化算法在控制各项关键特性、提高综合装配质量等方面的有效性。     

考虑弯扭变形的叶片模型配准方法

叶片测量数据与其CAD模型的配准定位是叶片几何形状分析的关键步骤。针对涡轮叶片的弯扭变形对叶片模型配准定位的不利影响,提出一种考虑弯扭变形的叶片模型配准方法,以提高叶片模型配准的可靠性与鲁棒性。在迭代最近点算法的目标函数中引入预变换函数,建立考虑弯扭变形的叶片模型配准目标函数。对叶片模型做切片化处理,进行弯扭变形分析生成叶片弯扭变形曲线,使用叶片弯扭变形曲线指导叶片测量数据配准。使用仿真生成带弯扭变形的叶片数据与通过坐标测量机获取的叶片实测数据对配准方法进行了验证。结果表明,所讨论方法能提高模型配准的可靠性,避免弯扭变形可能导致的叶片模型配准失败。     

基于局部几何特征的稠密点云配准方法

针对现有的稠密点云配准方法依赖初始位置设定、计算成本高、配准成功率不高等问题，提出了一种基于点云局部几何特征的稠密点云配准方法。采用深度卷积网络模型提取点云的局部几何特征，从而减少了三维点云数据的噪声、低分辨率和不完备性等带来的影响。在此基础上，使用K维树搜索完成局部几何特征描述子的关联工作。最后，通过随机采样一致算法对点云的相对位姿进行鲁棒的估计。通过对开源数据集上5个典型场景中的数据测试表明，该方法的配准成功率达到92.5%，配准精度达到0.0434m，配准时间相对最邻点迭代配准算法缩短了74.7%，实验结果验证了该方法的有效性、实时性和鲁棒性。     

A multi-constraints based pose coordination model for large volume components assembly

In the assembly process of large volume product, engineering constraints limit the relative pose of components and serve as a standard for judging assembly quality. However, in the traditional process of target pose estimation, a general method is needed for establishing the correlation between engineering constraints and product pose, and it is difficult to evaluate pose by constraints comprehensively. Therefore, the process of target pose estimation and evaluation is separated. In this paper, a pose coordination model based on multi-constraints is proposed, which includes pre-processing, pose estimation, pose adjustment and evaluation. Firstly, engineering constraints are decoupled into 4 types of Minimum Geometrical Reference Constraints (MGRC), and the inequalities for solving target pose are formulated. Then the Constraint Coordination Index (CCI) is defined as the optimization objective to solve the target pose. Finally, with CCI as the numerical index, the target pose is evaluated to illustrate the quality of assembly. Taking the simulation experiment of wing-fuselage jointing as an example, the external and internal parameters of model are analyzed, and the pose estimation based on multi-constraints reduces the CCI by 12%, compared with the point-set-registration method.     

Trajectory Planning Algorithm Based on Quaternion for 6-DOF Aircraft Wing Automatic Position and Pose Adjustment Method

 A 6-degree of freedom (6-DOF) aircraft wing position and pose automatic adjustment method is presented to improve ARJ21 wing-fuselage connection precision and efficiency. Wing position and pose are adjusted by three pillars which are driven by six high-precision servo motors. During the adjustment process, wing is tracked and positioned by laser tracker. Wing initial posi-tion and pose are calibrated by using the measurement coordinates of assembly reference points. Wing target position and pose are calculated according to wing initial, fuselage position and pose, and relative position and pose requirements between wing and fuselage for the connection. Combining Newton-Euler method with quaternion position and pose analyzing method, the inverse kinematics of servo motors, together with the adjustment system dynamics is obtained. Wing quintic polynomial trajec-tory planning algorithm based on quaternion is proposed; the initial, target position and pose need to be solved and the inter-mediate moving path is uncertain. Simulation results show that the adjustment method has good dynamic characteristics and satisfies engineering requirements. Preliminary engineering application indicates that ARJ21 wing adjustment efficiency and precision are improved by using the proposed method.     

An error analysis and optimization method for combined measurement with binocular vision

The accurate measurement of surfaces of large aviation components is vital for the assessment of manufacturing and assembly quality of such components. To satisfy the measurement requirement of large-size components, most current researches pay more attention to combined measurement methods utilizing different measuring instruments, but the related researches on error analysis and optimization methods are not taken enough attention. This paper proposes a combined laser-assisted measurement method with feature enhancement techniques, and it also develops an error propagation model of the main factors affecting the overall measurement error in detail. Firstly, the surface of a large-size component is measured by the measurement system at multiple stations. Secondly, a control point coordinate system is established as a bridge to unify all local measurement data into the global coordinate system. To improve the overall measurement accuracy, the pixel extraction error as a key factor causing the overall measurement error is analyzed in detail. Next, the error propagation model is established, and some optimization strategies of layout for minimizing measurement error and transformation error are researched. Finally, experiments are carried out to verify the effectiveness of the proposed method. The results show that the measurement error of the proposed method reaches 0.073% and 0.14% with a 1D standard ruler and a flat plate, respectively.     

基于力位协同控制的大飞机机身壁板装配调姿方法

为校正中机身壁板由于重力和调姿内力产生的变形，提高中机身壁板装配调姿精度，提出了一种基于力位协同控制的装配调姿方法。通过将调姿机构等效为并联机构，推导了调姿机构的解析正反解模型；根据螺旋理论，建立了力传感器测量值与重力、调姿内力之间的映射关系，实现重力补偿值的动态计算，基于局部刚体-弹性连接假设，通过多元线性回归方法构建了调姿内力转化为位置补偿量的模型；根据Clamped-Free变形协调原理，简化了定位器调姿内力之间的协调关系，在此基础上提出了重力前馈补偿和调姿内力转化为位置补偿的力位协同控制策略，并对其进行了理论分析与设计。最后，对所提出的控制策略进行了仿真分析，结果表明采用力位协同控制方法，调姿定位精度提高35.3%，调姿内力降低77.8%，通过应用实验，说明了该方法的可行性和有效性。     

MC-LRF based pose measurement system for shipborne aircraft automatic landing

Due to the portability and anti-interference ability, vision-based shipborne aircraft automatic landing systems have attracted the attention of researchers. In this paper, a Monocular Camera and Laser Range Finder (MC-LRF)-based pose measurement system is designed for shipborne aircraft automatic landing. First, the system represents the target ship using a set of sparse landmarks, and a two-stage model is adopted to detect landmarks on the target ship. The rough 6D pose is measured by solving a Perspective-n-Point problem. Then, once the rough pose is measured, a region-based pose refinement is used to continuously track the 6D pose in the subsequent image sequences. To address the low accuracy of monocular pose measurement in the depth direction, the designed system adopts a laser range finder to obtain an accurate range value. The measured rough pose is iteratively optimized using the accurate range measurement. Experimental results on synthetic and real images show that the system achieves robust and precise pose measurement of the target ship during automatic landing. The measurement means error is within 0.4° in rotation, and 0.2% in translation, meeting the requirements for automatic fixed-wing aircraft landing.Received 5 July 2022; revised 19 August 2022; accepted 27 September 2022.     

一种适用于曲面结构的机器人制孔误差在线补偿技术

针对工业机器人应用于飞机零部件自动钻孔时各项误差累积造成制孔精度差的问题，提出一种利用单应关系计算机器人驱动坐标三维偏差，以在线补偿机器人制孔精度的方法。首先利用外部测量设备建立机器人制孔系统中各坐标系关系；在标定阶段，通过以一定倾斜角度固联于机器人末端的相机拍摄一幅安装于制孔工作平面上与刀轴正对的平面标定板图像，并据此完成基于单应变换的手-眼关系标定；在实际制孔过程中，机器人在测距传感器及相机的辅助下，从基准孔理论坐标对应的姿态，不断调整至基准孔正上方理想位置，通过手-眼关系计算基准孔实际位置对应的机器人驱动坐标，然后根据一组基准孔的机器人三维驱动误差，计算三维驱动误差变换矩阵，据此获得这组基准孔邻域范围内各待钻孔的机器人驱动坐标补偿量，从而实现待钻孔定位误差补偿。以飞机结构实验件为对象进行了模拟制孔验证，实验结果表明，补偿前待钻孔三维综合定位误差和法向误差测量值范围分别为2.28~2.85 mm和2.09°~3.93°，平均为2.55 mm和3.30°，补偿后制孔最大误差分别不超过0.30 mm和0.21°，满足自动制孔位置精度要求。     

飞机装配几何量质量检测体系构建及关键技术

针对新一代飞机装配过程几何量检测的高精度、高效率和高可靠性需求,分析了飞机装配过程几何量检测特征和具体的检测要求,提出了用于不同测量任务的测量方法,构建了装配几何量质量检测体系.研究了复杂装配现场多源异构整体测量工艺仿真及精度优化、三维点云数据的拟合与对齐和基于整体测量场的多系统协同测量3项关键技术,开发了装配检测质量...     

基于凸包算法的陶芯弯曲度与扭曲度误差计算

陶芯弯扭变形直接关系到空心叶片的壁厚尺寸分布,为克服当前陶芯弯扭变形的计算中测量数据与理论模型三维配准、陶芯截面轮廓线提取或拟合的过程算法复杂、收敛速度慢、效率低等问题,提出了一种通过测量数据点直接计算陶芯弯曲度和扭曲度误差的算法,该算法不需要三维配准和提取陶芯外轮廓线,通过距离权值法计算陶芯弯曲度,凸包算法计算陶芯扭曲度,能大幅提高计算效率。仿真与实验结果表明:该算法弯曲变形计算精度为99.55%,与二维配准算法相差±0.01mm;扭曲变形计算精度为99.98%,与二维配准相差±0.006°。      

光学内反射零件与结构件粘接装调系统

通过内反射光学零件的分析,结合光学小角度测量原理,实现了内反射光学零件与结构件之间装调精度的在线实时装调,提高了光学组件装调的精度和装调效率。同时也为内反射光学零件与结构件装调定位走出了一条新路,对后续产品的光学装配及调试提供了新的方法。     

Research on uncertainty in measurement assisted alignment in aircraft assembly

Operations in assembling and joining large size aircraft components are changed to novel digital and flexible ways by digital measurement assisted alignment.Positions and orientations（P＆O）of aligned components are critical characters which assure geometrical positions and relationships of those components.Therefore,evaluating the P＆O of a component is considered necessary and critical for ensuring accuracy in aircraft assembly.Uncertainty of position and orientation（U-P＆O）,as a part of the evaluating result of P＆O,needs to be given for ensuring the integrity and credibility of the result;furthermore,U-P＆O is necessary for error tracing and quality evaluating of measurement assisted aircraft assembly.However,current research mainly focuses on the process integration of measurement with assembly,and usually ignores the uncertainty of measured result and its influence on quality evaluation.This paper focuses on the expression,analysis,and application of U-P＆O in measurement assisted alignment.The geometrical and algebraical connotations of U-P＆O are presented.Then,an analytical algorithm for evaluating the multi-dimensional U-P＆O is given,and the effect factors and characteristics of U-P＆O are discussed.Finally,U-P＆O is used to evaluate alignment in aircraft assembly for quality evaluating and improving.Cases are introduced with the methodology.     

一种基于3D扫描的航天器跨舱对接波导组件位姿测量方法

提出了一种基于Handyscan 700和Geomagic Control的非接触式位姿测量方法。该方法采用手持式便携3D扫描设备Handyscan 700,具有测量速度快、测量精度高的优点。在波导组件位姿测量试验中,本方法解决了航天器跨舱波导组件位姿无法高效测量的难题,实现了跨舱波导组件舱内部分在舱板合舱前就可安装到位,降低了总装风险,提高了波导组件总装效率。     

基于激光雷达的数字化装配检测技术研究

为提高新型飞机装配检测需求,提出了基于激光雷达的装配检测方法,使用激光雷达对装配零部件定位基准进行测量,并对测量数据进行分析,提取出关键尺寸信息,从根本上解决装配问题。结合飞机某部件装配检测实例,对其装配问题进行检测及分析,解决了飞机装配过程中配合尺寸超差问题。结果证明基于激光雷达的装配检测技术可高效准确地检测出飞机装配问题,对实现飞机数字化自动装配具有重要意义。     

大型飞机机身调姿与对接试验系统

为实现飞机大部件装配过程的数字化、自动化和柔性化,研制了大型飞机机身调姿与对接试验系统.阐述了该系统的工作原理,通过激光跟踪仪测量试验机身上的检测点,集成管理系统计算试验机身的位姿,控制系统驱动多个三坐标数控定位器协同运动,实现试验机身的调姿与对接.建立了位姿调整机构的运动学模型,针对构建的硬件平台完成了包括集成管理系...     

机器人在轨装配无标定视觉伺服对准方法

针对在轨装配过程中机器人"手眼"关系无法进行有效标定及机器人系统和被操作物惯性参数不定的情况,在传统的无标定视觉伺服基础上设计了深度估计器,基于机器人和图像运动的测量数据在线估计目标特征的深度值,并在机器人关节控制环中设计滑模控制器实时控制机器人关节运动,根据反馈图像信息纠正系统误差完成对准跟踪,通过仿真验证了方法的有效性。所提的无标定视觉伺服对准方法使机器人在装配过程中免去了复杂的"手眼"关系的标定程序,克服了机器人系统及被操作物惯性参数不确定性给装配精度造成的影响,提高了"手眼协调"的鲁棒性,保证机器人能够在复杂的太空环境下完成在轨装配任务。     

基于光场成像的快照式气膜孔三维测量技术

叶片气膜孔的几何参数对其冷却效率具有十分重要的影响,需采取有效手段对加工的气膜孔几何参数进行检测。基于光场成像原理,初步探索了单光场相机快照式三维测量技术在气膜孔检测上的应用。与其他光学测量技术相比,该技术仅通过一次拍摄,即可快速从捕获的单张原始光场图像中计算得到气膜孔的三维点云数据,其数据采集效率很高。实验中对一组标准量块进行了测量,展示了单光场相机应用于工业级精密测量的潜力。对实际叶片上气膜孔几何参数的检测结果初步表明了该技术应用于气膜孔三维测量的可能性。由于单光场相机成像系统的结构简单,易于操作且便于与其他传感器设备集成,可为气膜孔三维测量问题提供一种新的解决方案。