BNi-2非晶钎料钎焊高铌TiAl合金与GH3536合金接头组织与性能

采用非晶态BNi-2钎料成功实现了高铌TiAl合金与GH3536合金的连接,获得良好的钎焊接头。钎焊接头的典型界面组织为TAN/B2+τ3/τ4+（Ni-Ti）-B/γ+（Ni-Ti）-B+CrB+G相/GH3536。通过分析钎焊温度对接头界面微观组织的影响,表明BNi-2钎料中B元素的扩散以及GH3536合金向液态钎料中的溶解对界面组织结构演变起着至关重要的作用。而随着钎焊温度的升高,扩散IV区逐渐消失,接头由4个区域变为3个区域,τ3/τ4化合物层及钎缝区域均逐渐增厚,黑色CrB相发生粗化,细小点状（Ni,Ti）-B含量减少。1 160℃保温10 min时,所获得的钎焊接头最大室温及高温（700℃）抗剪强度分别为~106.8 MPa和~76.2 MPa,其剪切强度降低约28.6%,接头均呈现脆性断裂模式。接头形成过程可以划分为固相扩散、液相生成、等温扩散凝固和残余液相析出4个阶段。     

TiAl合金与40Cr钢的真空钎焊研究

采用Ag-Cu-Ti钎料进行了TiAl合金与40Cr钢的真空钎焊连接,用拉伸试验对接头的连接强度进行检验,采用扫描电镜、电子探针和X-射线衍射分析等手段对接头断口的形貌、界面原子扩散、界面反应及界面产物进行了分析.研究结果表明,采用Ag-Cu-Ti钎料时得到的焊缝具有很高的强度(426MPa),是因为钎料和TiAl母材中的Ag,Cu,Ti原子发生了互扩散,而且在钎料与母材的界面发生了界面反应,形成了AlCu2Ti相,实现了冶金上的结合.     

激光毛化对Cf/SiC与TC4钎焊接头组织及性能的影响

由于线胀系数差异大,Cf/Si C复合材料与TC4钛合金钎焊接头容易形成较大的内应力而开裂失效。为了进一步提高接头强度,应用激光毛化工艺在Cf/Si C表面烧蚀出微孔,采用银基钎料对Cf/Si C与TC4进行钎焊。焊后对接头力学性能进行测试,对接头界面及断口显微组织进行观察。结果表明:焊前对Cf/Si C表面进行激光毛化处理,钎料能够填充微孔并形成良好的钎焊界面,能够提高Cf/Si C与TC4钎焊接头的剪切强度。     

Microstructure and high-temperature oxidation behavior of plasma-sprayed Si/Yb2SiO5 environmental barrier coatings

An environmental barrier coating (EBC) consisting of a silicon bond coat and an Yb₂SiO₅ top-coat was sprayed on a carbon fibers reinforced SiC ceramic matrix composite (CMC) by atmospheric plasma spray (APS). The microstructure of the coating annealed at 1300 °C and its high-temperature oxidation behavior at 1350 °C were investigated. The significant mass loss of silica during the plasma spray process led to the formation of Yb₂SiO₅ and Yb₂O₃ binary phases in the top-coat. Eutectics of Yb₂SiO₅ and Yb₂O₃ were precipitated in the top-coat, and channel cracks were formed in the top-coat after 20 h annealing because of the mismatch between the coefficients of thermal expansion (CTEs) of Yb₂SiO₅ and the SiC substrate. The EBC effectively improved the oxidation resistance of the CMC substrate. The channel cracks in the Yb₂SiO₅ top-coat provided inward diffusion channels for oxygen and led to the formation of oxidation delamination cracks in the bond coat, finally resulting in spallation failure of the coating after 80 h oxidation.     

TC4/72Ag-28Cu 钎焊组织及Ti-Cu化合物

在钎焊温度1103K一定的条件下,分析了钎焊时间对TC4/72Ag-28Cu/TC4钎焊接头组织及分布形态的影响.研究表明钎焊时间较短,扩散到界面的Ti、Cu在冷却过程中通过共析转变形成了Ti2Cu化合物;钎焊时间大于某一临界值,由于母材中Ti大量向钎缝中溶解及在界面Cu相对浓度的降低,使钎缝中Cu全部固溶在Ti中,最终Ti2Cu化合物消失.在此基础上提出了临界钎焊时间的概念.     

Wetting behavior of AgCu-4.5Ti filler reinforced by carbon nanotubes on C/C composite

The effect of Carbon Nanotubes (CNTs) content on the wettability of AgCu-4.5Ti + x CNTs (wt%) composite filler alloys on C/C composite was investigated. The results show that the added CNTs reacted with element Ti in the filler and produced the dispersed fine in situ synthesized TiC particles, which increased the consumption of element Ti and provided the nucleus for the growth of Ti-Cu compounds simultaneously. The above effects of introducing CNTs, inhibited the formation of Ti-Cu compounds, also changed the distribution of compounds, which dramatically influenced the interfacial microstructure and characteristics of wetting behavior. The increase of CNTs content refined and dispersed coarse Ti-Cu compounds, decreased the initial spreading temperature, and improved the wettability, but high content of CNTs (more than 0.3wt%) decreased the wettability of the filler alloy. The wetting interfacial microstructure of corresponding composite filler alloys were analyzed by Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectrometer (EDS) and Transmission Electron Microscope (TEM), which consisted of TiC, TiCu, TiCu₂ and TiCu₄ compound. The typical wetting behavior of AgCu-4.5Ti + 0.3wt% CNTs composite filler on C/C composite was divided into four stages. The effect mechanism of CNTs content on the wetting behavior was proposed.     

大间隙钎焊用混合粉状高温镍基钎料的润湿性和显微组织

用一种含Al,Ti元素的镍基钎料粉末与γ’相沉淀强化型镍基高温合金FGH95的粉末混合,制备了大间隙钎焊用混合粉状高温镍基钎料。实验表明,采用合适的混合比例,混合粉状钎料对1Cr18Ni9Ti不锈钢具有较好的润湿铺展性。该混合钎料所获得的钎缝金属的合金化效应显著,Al+Ti合金元素的最大含量达到了5.49%。焊态钎缝中,除Nb,W等个别元素外,其他主要强化元素无明显偏析,且经1180℃/4h扩散处理可消除合金元素的偏析。钎缝金属的组织状态较为均匀,基体为等轴γ固溶体枝晶,枝晶间分布有颗粒状、短条状的化合物相以及少量的γ+γ’共晶组织。另外,在γ固溶体中分布着大量弥散细小γ’沉淀强化相。     

Influence of welding parameters on microstructure and mechanical properties of electron beam welded Ti60 to GH3128 joint with a Cu interlayer

Effects of welding parameters on the microstructure and mechanical properties of Ti/Cu/Ni joint welded by electron beam were investigated. High welding heat input increased the melting quantity of Ti60 titanium alloy and promoted the formation of Ti–Cu intermetallic compounds (IMC) such as Ti₂Cu and Ti₃Cu₄, increasing the brittleness of the joints. Low welding heat input was not conducive to the complete melting of the copper interlayer, and the unmelted copper reduced the performance of the joints. Under the optimal welding parameters, Ti–Ni IMCs in the weld would be replaced by (Cu, Ni) solid solutions ((Cu, Ni)_ss). However, Ti–Cu IMC layers cannot be eliminated entirely by changing the welding parameters. The maximum tensile strength of the joints was 201 MPa. The fracture of the joints occurred at the Ti–Cu IMC layer, which was a typical brittle fracture.     

Ti基钎料中添加混合稀土对TC4合金钎焊性能的影响

通过对钎料综合性能的对比,研究了混合稀土的添加对Ti-Zr-Cu-Ni系合金钎料性能,以及对真空钎焊TC4母材的钎缝的组织特征和机械性能的影响。研究结果表明:添加适当含量的混合稀土的钎料熔点降低,润湿性好,钎焊TC4的力学性能好,混合稀土的含量不应超过5%。     

双层氧化物生长下热障涂层的界面失效与应力演化

在长时高温服役环境下,热障涂层（TBCs）会在内部的陶瓷层（TC）和粘结层（BC）之间生成由Al2O3层和混合性氧化物层（MO）组成的双层热生长氧化物（TGO）。其中,后期生成的MO 由于其疏松多孔、脆性大等特点,极易造成涂层内微裂纹的形成和扩展,导致涂层的过早剥落。因此,依据双层TGO 生长的扩散—氧化模型,在考虑材料非线性变形行为的基础上,运用生死单元法模拟TBCs 内双层TGO 异向生长下涂层界面的失效与应力演化过程。结果表明：MO 的生长会大幅度提升涂层界面的拉伸应力水平,易导致MO/TC 界面在高温阶段波峰区域和冷却阶段斜坡中心区域发生破坏及失效;MO/TC 界面的失效会引起BC 层波峰处更高的拉伸应力,促进冷却阶段Al2O3/BC 界面从波峰向波谷处的破坏;MO/TC 界面失效后,hAl2 O3 /hMO 的增加会加速Al2O3/BC 界面的破坏。     

表面改性C/C复合材料与LAS玻璃陶瓷的连接

采用MgOAl₂O₃SiO₂(MAS)玻璃作为中间层,对SiCMoSi₂表面改性的C/C复合材料与Li₂CO₃Al₂O₃SiO₂(LAS)玻璃陶瓷进行热压连接。通过正交实验,研究了连接温度、连接压力和保温时间对试样连接强度的影响,确定最佳工艺参数为：1 200 ℃,20 MPa,15 min,所得到连接接头的最高剪切强度可达30 MPa。利用扫描电子显微镜（SEM）、能谱仪（EDS）和背散射电子像（BEI)对SiCMoSi₂涂层、连接界面的形貌以及组成进行了分析。研究结果表明,SiCMoSi₂涂层与基体结合紧密,Si,C元素在界面处呈梯度状分布,形成厚度约为15 μm的过渡层。MAS玻璃中的组分与LAS玻璃陶瓷和SiCMoSi₂涂层存在相互渗透现象,形成紧密的C/C(SiCMoSi₂)/MAS/LAS结构,界面间的结合良好。     

弯曲纤维对SiO2f/SiO2复合材料拉伸强度的影响

以SiO_(2f)织物作为增强相,采用循环浸渍固化工艺,制备了SiO_(2f)/SiO_2复合材料。在制备过程中,通过对SiO_(2f)织物进行模压处理,使SiO_(2f)呈现出不同程度的弯曲,测定了纤维弯曲后复合材料的拉伸强度,研究了纤维弯曲时复合材料的断裂过程。结果表明:弯曲纤维将导致复合材料的拉伸强度下降,最低拉伸强度仅为5.5 MPa,纤维弯曲时复合材料的断裂过程为逐层断裂,断裂应变增加,最大断裂应变达到1.19%。     

Brazing of C/C composite and Ti-6Al-4V with graphene strengthened AgCuTi filler: Effects of graphene on wettability,microstructure and mechanical properties

Graphene nanosheets(GNSs) strengthened AgCuTi composite filler(AgCuTi_G) was used to braze C/C composite and Ti-6Al-4V. The effects of GNSs on the wettability of AgCuTi_G filler on the C/C composite surface and the interfacial microstructure and mechanical properties of brazed joints were investigated. The results indicate that the addition of GNSs reduced the wettability of AgCuTi_G. The interfacial microstructure of brazed joints evolved with the addition of GNSs, where Ti_3Cu_4 and TiCu_4 were converted to TiCu and the thickness of the reaction layer adjacent to the base material decreased. The maximum shear strength of joints brazed at 0.3 wt% GNSs was 23.3 MPa(880℃/10 min). Further adding GNSs deteriorated the shear strength of the joints. Fracture of the joints occurred in the C/C composite substrate and the TiC layer adjacent to C/C composite.     

TC1钛合金蜂窝夹层结构的钎焊工艺研究与分析

研究了TC1钛合金蜂窝夹层结构试件的钎焊工艺,通过对系列工艺下钎焊界面组织进行观察得出,在930℃/保温15min和一定钎料添加量的条件下,界面析出了TiNi2(Cu,Zr)化合物,且尺寸细小、分布弥散,因而相应钎焊试件的室温拉脱强度平均值较高,可达17MPa。在钎焊过程中,Cu和Ni元素由钎料向母材扩散,使母材β相变温度降低,导致界面魏氏体组织的产生;芯体波纹带间受钎料熔化热影响较大,导致此处魏氏体组织粗大,成为试件的薄弱部位。     

钴对钛基钎料钎焊Ti3Al的影响

研究了Co的添加对Ti-Zr-Ni-Cu钎料的性能,以及对Ti3Al基合金钎焊接头的显微组织和机械性能的影响。研究结果表明:采用添加Co的钎料,具有良好的润湿性和流动性,可显著提高钎焊接头的拉伸强度。     

镍基非晶态及晶态钎料真空钎焊时母材在钎料中溶解特性的研究

以高温钎焊时液态钎料对母材溶解厚度的定量计算模型为基础，考察了采用Ｎｉ８２Ｃｒ７．５Ｓｉ４．５Ｂ３Ｆｅ３成分的镍基非晶态及晶态钎料真空高温钎焊１Ｃｒ１８Ｎｉ９Ｔｉ不锈钢时钎料对母材的溶解特性，深入研究了钎焊温度、钎焊保温时间以及钎焊间隙等参数对母材溶解厚度的影响。结果表明，钎焊温度对母材溶蚀的影响比钎焊保温时间剧烈，而钎焊间隙增加明显促进了母材的溶解，采用母材溶解厚度计算模型可对溶蚀控制条件下的钎焊规范及钎焊间隙等参数进行优化匹配。     

SiC陶瓷与GH128镍基高温合金反应连接研究

采用 Fe-Ni(重量比为 65∶ 3 5)金属粉末焊料,利用 Gleeble1 50 0热模拟机对镍基高温合金 ( GH1 2 8)和 Si C陶瓷进行反应连接,研究了连接温度、连接压力和高温保温时间对试样连接强度的影响,确定了最佳工艺参数,并制备了剪切强度超过 3 4.3 MPa的陶瓷 /金属连接件。界面结构分析表明陶瓷 /焊料界面反应层的形成主要受 Fe,Ni原子向陶瓷中的扩散引起     

莫来石陶瓷的制备、微波介电特性及其对材料吸波性能的影响

采用热压烧结法,用SiO₂溶胶和Al₂O₃溶胶制备的莫来石溶胶制备了莫来石陶瓷,研究了莫来石陶瓷的微波介电特性与烧结致密度之间的关系。研究表明,当莫来石陶瓷的烧结致密度从91.4%升高到97%时,其复介电常数的实部ε从3.85增加到的5.87,虚部ε″从0.04增加到0.11。当添加MgO烧结助剂后,莫来石陶瓷复介电常数的实部和虚部明显升高。将莫来石陶瓷作为吸波材料阻抗变换层,能够大幅度提高材料的吸波性能。这主要是由于采用的莫来石阻抗变换层的波阻抗较高,为156Ω,减小了空气与吸收层界面上电磁波的反射,使更多的电磁波进入了吸收层而被损耗。     

Interfacial characteristics in CNTs-AgCuTi systems

AgCuTi-based composite fillers reinforced with Carbon Nanotubes（CNTs） were prepared by mechanical ball milling and ultrasonic agitation. The morphological features, chemical components, and melting characteristics of the composite fillers with different content of CNTs addition were investigated using Field Emission Scanning Electron Microscopy（FESEM）, XRay Diffraction（XRD） and a Differential Scanning Calorimeter（DSC）. After being heated at 900 ℃, the microstructure of the composite fillers was ...     

Brazing diamond grits onto AA7075 aluminium alloy substrate with Ag–Cu–Ti filler alloy by laser heating

The brazing of diamond is a promising way to fabricate grinding wheels for efficient machining and precision grinding. This work investigated the feasibility of bonding diamond grits onto Aluminium Alloy 7075 (AA7075) substrate with a Ag–Cu–Ti filler alloy via laser fusion brazing. The interfacial microstructures and the strength of the brazed diamond joints were studied. The cross-section of the brazed diamond joint consists of a molten filler alloy layer, a molten pool, a heat effect zone, a columnar crystal zone and an equiaxed crystal zone. Within the interface of the filler alloy/substrate metal, microstructures observed possibly were Ag(s.s), Al(s.s), TixAl, Al2Cu and Mg intermetallic compounds. A layer of TiC with a thickness of about 30–50 nm was found at the bonding interface of the diamond/filler alloy. The averaged peak shear force of the brazed joints was found to be approximately 39.8 N. The abrasion grinding test indicated that the diamond/AA7075 brazed joint was adequate for grinding. However, the pulled-off of grit was found to be the primary failure of this type of brazed joint. This work broadened the brazing diamond technique and the range of applications of brazed diamond wheels for efficient grinding.