湿滑道面飞机轮胎临界滑水速度计算方法比较

以美国国家航空航天局(NASA)临界滑水速度计算公式为基础,基于耦合欧拉-拉格朗日(CEL)算法建立动流场冲击原地转动轮胎分析模型,并由NASA公式及试验数据验证了模型的正确性及NASA公式在重轴载高胎压范围的适用性。进而考虑实际道面积水状态,建立滚动轮胎冲击静流场模型,探讨实际积水状态对临界滑水速度的影响。通过两类模型对比分析得出:两类模型的轮胎-水膜相互作用机理不同,相同速度和胎压下,后者在轮胎前缘形成的动水压强峰值明显高于前者,表明滚动轮胎冲击静流场模型中轮胎受到动水压强抬升作用更为显著,且相同速度条件下,滚动轮胎冲击静流场分析模型计算的竖向支撑力和临界滑水速度始终低于动流场冲击滚动轮胎的结果,表明该模型计算结果偏于安全,更适用于飞机高速滑行中轮胎-水膜相互作用分析。据此,提出了基于道面积水状态的临界滑水速度计算公式。     

一种分析轮式起落架直升机“舰面共振”的方法

 针对轮式起落架直升机，提供了一种“舰面共振”动力稳定性分析方法。首先，针对直升机在舰面上随舰船一起摇晃时左右起落架受载不对称的状况，近似采用受对称载荷产生对称变形、受非对称载荷产生非对称变形的方法计算了直升机的平衡状态；其次，根据轮式起落架轮胎和缓冲支柱刚度和阻尼共同作用的特点，结合轮式起落架的几何关系，采用复刚度的方法得出起落架作用于机体的刚度与阻尼；最后，用桨叶振动模态法对轮式起落架的直升机进行了不同旋翼升力卸载以及鱼叉系留与否的“舰面共振”动力稳定性计算分析，并通过算例得到验证。     

基于弹性起落架的直升机系留载荷计算

根据舰载直升机舰面系留时的受力特点,以弹性起落架的垂向变形为变量,根据虚位移原理建立了直升机在摇荡舰面系留的动力学分析模型。运用牛顿迭代法对横摇、纵摇、有风以及无风情况下系留索具载荷进行了计算,发现横摇角较大时载荷主要分布于主起落架系留索上,且风载的影响并不能忽略。分析了轮胎刚度对系留索载荷的影响,结果表明,起落架轮胎刚度由300N／mm增加至800N／ram时,最大张力减小了7．43％,说明增加轮胎刚度能有效提高直升机系留的安全性。     

飞机载荷机构特性曲线的自动检测

基于飞机飞行品质和装备科学保障的基本要求,提出了载荷机构特性曲线自动检测的原理方案,研制了相应的通用性自动检测仪,并成功地实现了载荷机构特性曲线的实时自动检测。检测结果准确可靠,为分析飞机操纵系统品质提供了直接的参考依据,对提高飞机操纵的可靠性、安全性和维修保障性具有重要意义。     

一种用于主动流动控制的气泡型微致动器

 面向先进主动流动控制,在国内率先研发了一种基于微机电系统(MEMS)的气泡型微致动器阵列技术。分析了气泡型微致动器用于主动流动控制的原理,阐述了致动器结构及其加工工艺。通过对气泡样件的压力载荷 变形行为的测试,表明其具有较好的线性和较大承载能力。结合不同翼型的风洞试验表明,微致动器作动可以影响翼型表面的压强分布,从而可用于增升等控制目的。     

飞机前起落架在转弯控制状态下的摆振分析及应用

对飞机前起落架在转弯控制状态下进行了摆振分析,通过主动力做功分析对转弯控制系统设计提出了建议和要求,应用耗能等效原理建立了主动力和等效粘性阻尼力间的关系。建立并求解以轮胎变形为主的摆振方程组得到主动力摆振区和摆振动态响应曲线,根据动态响应的收敛速度确定防摆所需的主动力及转弯作动器的有效活塞面积。     

竹象虫后翅结构力学和空气动力学特性

为研究长足大象甲后翅结构特性和飞行过程的空气动力学特性,建立长足大象甲后翅翅脉特征曲线的数学模型,利用有限元软件对其进行均匀载荷、垂直载荷和扭转载荷3种不同载荷下的静态分析和模态分析。基于嵌套网格法在Fluent软件中模拟后翅上下扑动,分析不同扑动幅值、扭转角度和扑动频率下的后翅升力系数和阻力系数变化规律。结果表明：长足大象甲后翅翅脉分布具有良好的结构刚度和承载能力,在受到不同载荷时,位移和应力的变化较小,结构稳定性较强,并且后翅振动频率为90.312 Hz,与同类昆虫相比,更符合微型扑翼飞行翼研发要求。此外,模拟试验表明长足大象甲后翅可以通过改变扑动幅值、扭转角度和扑动频率来提高升力和推力以实现特技飞行。     

等效载荷的Haigh修正方法

本文在不同材料疲劳试验结果的基础上,分析了不同材料的平均载荷对疲劳交变载荷的影响,其等效载荷的修正呈现出不同的曲线线性.文中通过引入Haigh系数,统一了等寿命曲线分析中等效载荷的Goodman/Soderberg/Gerber修正方法,并给出不同材料平均载荷对等效载荷影响的修正曲线的系数.     

液体火箭发动机再生冷却结构弹塑性分析

为了分析推力室壁应力和变形分布情况,研究推力室失效位置和失效机理,建立了一种弹塑性有限元分析方法。建立推力室一维流动传热模型,为结构弹塑性分析提供输入。进一步建立推力室壁在温度和压强载荷下的二维弹塑性计算模型,分析了在预冷-工作-后冷-关机的工作循环下推力室壁的应力应变响应,比较了温度载荷和压强载荷的作用程度,并预估了推力室使用寿命。结果表明：推力室壁产生的弹塑性变形是由温度载荷和压强载荷共同作用所致,温度载荷起主导作用。推力室内壁冷却通道中心位置最先发生失效破坏,限制了推力室的使用寿命。从计算时间和准确性来说,该方法能够为再生冷却通道的优化设计和性能估算提供参考。     

弹性飞机结构动载荷应用研究

民用、军用飞机结构设计规范要求对于弹性飞机必须采用动态分析方法确定结构各部分的飞行载荷,分析中须计及飞机的气动力(非定常、定常)、结构动力(弹性力、惯性力)与飞行控制系统之间存在的耦合。文中对实际飞行中升降舵机动、升降舵自动驾驶遭遇突风情况下机体结构动力响应进行了计算分析,探讨结构动载荷预计中的建模技术,评估了舵面激励对弹性飞机动载荷的影响,对飞行状态中飞机动载荷分析相关工作有借鉴意义。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.