共查询到20条相似文献,搜索用时 140 毫秒
1.
文章介绍了以373型精密露点仪为主标准器的湿度标准装置的原理及构成,对该装置的重复性和稳定性进行了测试。结果表明温度重复性实验的标准偏差为0.00℃,相对湿度重复性实验的标准偏差为0.07%RH,露点温度重复性实验的标准偏差为0.01℃。温度稳定性实验的标准偏差为0.02℃,相对湿度稳定性实验的标准偏差为0.33%RH,露点温度稳定性实验的标准偏差为0.066℃。基于美国NI公司的Labview软件开发平台,开发了湿度仪器仪表计量软件。软件以模块化思想为基础,可实现数据自动处理,报告自动生成。 相似文献
2.
期间核查是指测量仪器在两次校准或检定的间隔期内对测量仪器的状态进行的核查。本文介绍了一种适用于气体活塞式压力计标准装置的期间核查方法,即采用平均值-标准偏差控制图对该标准装置的测量过程进行统计分析,以确认测量过程是否处于稳定受控状态。 相似文献
3.
4.
5.
6.
音速喷嘴式气体流量标准装置是气体流量重要的计量标准,其测量过程的情况直接反映了装置的准确性、重复性、稳定性。使用控制图可以记录装置的测量过程,并由此判断其测量过程是否处于受控状态。本文介绍了平均值-极差控制图在音速喷嘴式气体流量标准装置测量过程中的应用。 相似文献
7.
8.
对8902A测量接收机用作高频中,小电压标准进行了分析研究,介绍了一种检定超高频毫伏表的新方法,并给出了实验数据,对该标准装置的不确定度进行了分析。 相似文献
9.
10.
发展了一种应用于流管实验装置的现场传声器阵列校准方法.该方法利用两支标准传声器的测量结果计算管内声场,然后比对待校准传声器的测量信号得到其灵敏度.与传统校准方法相比,该方法具有实时快速、能提供相位校准等优点.在流管装置上进行实验,用模态匹配方法对校准结果进行校核,显示该校准方法得到的声压与计算结果吻合得更好.使用本方法,利用高精度传声器对低精度传声器进行校准并应用,可有效降低测量实验成本. 相似文献
11.
12.
Nikolaus Peter Schmitt Wolfgang Rehm Thomas Pistner Paul Zeller Hermann Diehl Peter Nav 《Aerospace Science and Technology》2007,11(7-8):546-552
The development and first flight tests are described of a short pulse direct measuring UV LIDAR for the measurement of gusts, turbulence and potentially wake vortices. The results of these stage 1 tests confirm that relative wind velocities can be measured with a standard deviation of below 10 m/s even at high altitudes with no appreciable aerosol concentrations. Operating the system under various flight conditions including rain, dense clouds, and clear air up to 24,000 ft was highly successful. Means to push the standard deviation below 1.6 m/s, foremost by increasing the laser output power and the efficiency of the light collecting system, are identified and quantified. Questions of instrument stability are addressed. 相似文献
13.
基于光线跟踪法建立了玻璃-液态碳氢燃料-玻璃3层平板总透射比的正问题模型,给出了反演液态碳氢燃料热辐射物性参数(光谱吸收指数 k 和光谱折射指数 n)的反问题模型,采用Monte-Carlo(M-C)法结合区间逼近法求解.通过将已知文献中庚烷的热辐射物性参数作为“真实值”,采用正问题模型计算总透射比作为“实验测量值”,然后利用反问题模型计算 n 和 k ,并分析实验偏差对反演计算的影响.研究结果表明:①模型反演 k 计算误差的标准差小于0.003%,而 n 的标准差高于21%.②实验偏差对反演计算影响较大,且偏差达到1.0%时个别反演数据明显“失真”.③ k 反演计算误 差的标准差 y 与实验偏差 γ 满足 y =2285.2 γ2- 10.484 γ +0.0037的关系式; n 反演计算误差的标准差受实验偏差影响较小,但偏差导致反演 n 误差均超过20%. 相似文献
14.
The impact of target radar cross section (RCS) fluctuations on the thermal noise limited accuracy of radar measurements of range, range rate, and angle is evaluated for Swerling fluctuation models. The impact is expressed as a modification of the large-signal approximation to the standard deviation σ of measurement error 相似文献
15.
针对空间非合作航天器姿态测量时受光照和地球背景影响大的问题,提出了一种基于卷积神经网络的端到端姿态估计方法.在该方法中,主干网络采用AlexNet与ResNet.首先,移除主干网络末端的全连接层,并列连接3个全连接层,采用三分支网络分别对姿态角进行估计.然后,设计了将分类问题与回归问题相结合的损失函数,通过分类方法将姿态估计限定在某一范围内,再使用回归方法进一步微调姿态.姿态分类损失函数确定姿态角度基准点,姿态回归损失函数对估计角度进行微调.相较于仅采用回归方法进行姿态估计,此方法能够有效减小姿态估计平均绝对误差、标准差与最大误差.实验对比了不同主干网络的测量精度,平均绝对误差在0.376°~0.746°之间,最优标准差为0.474°. 相似文献
16.
针对天线反射面研制过程中的精度测量,提出一种基于CAD模型的自动测量技术和反射面数据处理技术的精度测量方法。在测点均匀布局规划和工件与模型对齐的基础上,自动获取反射面的完整测量数据,利用最优化算法使实测数据和理论模型达到最佳匹配,实现反射面面形精度的准确评价并获得变换矩阵。最终通过偏差矢量图表达天线反射面的面形偏差趋势,并利用获得的变换矩阵修正加工基准,有效保证了反射面的成型精度和加工精度,工程应用表明该方法较好地满足了反射面制造过程中的测量需求。 相似文献
17.
针对航空重力测量对数据后处理的要求,结合平台式重力仪系统的组成与工作原理,在重力异常信号的频域特征基础上,设计出一套有严格频域规范的航空重力数据后处理流程,并对某海域实测数据进行了处理。结果表明,重力异常值内符合精度为12条东西测线达到0.43mGal/140s和0.84mGal/100s,4条南北测线达到0.39mGal/140s和0.79mGal/100s;以同测线GT-2A单次测量结果为标准值统计标准差,12条东西测线为0.72mGal/140s和0.98mGal/100s,4条南北测线为1.41mGal/140s和1.53mGal/100s。结果表明,设计的航空重力测量数据后处理方法可以实现重力异常信号的高精度提取。 相似文献
18.
在确定的函数关系(数学模型)中,因变量(输出量)随自变量(输入量)的变化规律完全由数学逻辑所确定,自变量到因变量的传递系数(灵敏系数)也可由因变量的标准差和自变量的标准差之比所决定,而与自变量的来历(测量的或者给定的)没有关系[1].本文根据这一基本原理,采用模拟自变量随机变化的方法,成功计算了手持式激光测距仪的测距固定偏差和比例偏差系数的测量不确定度,从而计算出测距标准差综合评定的扩展不确定度,同时解决了复杂的数学模型中多个输入量到输出量的灵敏系数和输出量的不确定度的计算问题. 相似文献
19.
《中国航空学报》2023,36(5):175-186
The accuracy of model attitude measurement has an important impact on wind tunnel test results. Microelectromechanical System Inertial Measurement Unit (MEMS IMU) provides a feasible way to measure model attitudes with high accuracy. However, the installation error between MEMS IMU coordinate system and the body coordinate system of test models can make the accuracy of the model attitude measurement decrease. In wind tunnel tests, the installation error depends on the relationship between the IMU and the model mechanism before tests. Therefore, in-field calibration in wind tunnel tests is necessary to reduce installation errors. To improve attitude measurement accuracy, the least squares quaternion calibration method based on MEMS IMU and six-position calibration procedure are proposed. High-precision three-axis turntable tests are performed. The pitch accuracy after calibration is higher than that before calibration in the angle of attack sweeping tests. The Root-Mean-Square Errors (RMSE) in the roll and yaw are within 0.01°, which are smaller than those before calibration. In the roll sweeping tests, RMSE of three attitude angles decrease significantly. In hypersonic wind tunnel tests, the pitch errors before and after calibration are within 0.05° and 0.02° in the angle of attack sweeping tests without wind. In five angle of attack sweeping tests with wind, the deviation between the mean of the pitch and the pitch after the elastic angle correction is within 0.03° and the standard deviation of five tests is within 0.01°. The proposed method is confirmed to enhance the accuracy of attitude measurement effectively, which is convenient for engineering applications. 相似文献
20.
GNSS导航星座主要由GPS、GLONASS、Galileo、BDS四大系统卫星组成,到2020年,用户有望同时观测到40多颗导航卫星,大幅提升导航性能的同时,也扩展了其应用领域。针对靶船、渔船对航向测量的需求,基于GNSS接收机应用现状,设计了低成本GNSS测向系统,使用2块Ublox LEA-M8T模块和STM32F407处理器搭建原理样机硬件平台,开展基于Kalman滤波器的载波相位差分姿态测量算法研究和基于Kalman滤波器的伪距差分姿态测量算法研究。静态实验表明,在8.5m基线的情况下,航向角测量标准差为0.0396°,俯仰角测量标准差为0.0889°。使用伪距差分算法,纬度方向上测量误差标准差为0.5923m,经度方向上测量误差标准差为0.4609m,高度方向上测量误差标准差为1.0766m。 相似文献