Properties of tandem balloons connected by extendable suspension wires

The tandem balloon system has been known as a candidate system for long duration flight balloons. In this paper, the properties of the system are analytically studied in a new way by introducing an extendable suspension wire in the Sky Anchor configuration, which consists of a zero-pressure main balloon suspending a payload and a super-pressure balloon suspended below the payload. It was found that extension of the suspension wire between the payload and the super-pressure balloon can extend the capability of the tandem system; the altitude of the zero-pressure balloon can be changed without any consumables except some energy, and the day–night oscillation of the balloon altitude can be suppressed. This property is useful as the vehicle for long duration flights. It is also pointed out that the method to control the altitude of a balloon using an additional suspended super-pressure balloon can also be applied for super-pressure balloons.     

High altitude flights in equatorial regions

A thorough analysis of balloon flights made from Hyderabad, India (Latitude 17°28′N, Longitude 78°35′E), and other equatorial sites has been made. It has been shown that limited success is expected for flights made from equatorial latitudes with balloons made out of natural colour polyethylene film, since the best known balloon film in the world today viz. Winzen Stratofilm is tested for low temperature brittleness only at ?80°C., whereas the tropopause temperatures over equatorial latitudes vary between ?80°C and ?90°C. The success becomes even more critical when flights are made with heavy payloads and larger balloons particularly at night when in the absence of solar radiation the balloon film becomes more susceptible to low temperature brittle failure. It is recommended that in case of capped balloons longer caps should be used to fully cover the inflated protion of the balloon at the higher level equatorial tropopause. It is also advised that the conditions such as wind shears in the tropopause should be critically studied before launching and a day with the tropopause temperature nearer to ?80°C should be chosen. Special care also should be taken while handling the balloon on ground and during launching phase. Properties of Winzen Stratofilm have been critically studied and fresh mandates have been recommended on the basis of limiting values of film stresses which caused balloon failures in the equatorial tropopause. It is also emphasized that the data on such flights is still meagre especially for flights with heavy payloads and larger balloons. It has been also shown that it is safest to use balloons made out of grey coloured film which retains its flexibility with the absorption of solar radiation, the success obtained with such balloons so far being 100%. The drawback, however, is that these balloons cannot be used for night flights. Stratospheric wind regimes over Hyderabad are also discussed with a view to determine the period over which long duration flights can be made. The data available, however, is meagre and it is recommended that more frequent special wind ascents be made to collect adequate statistical data from which reliable conclusions could be drawn through critical analysis.     

External caps: An approach to stress reduction in balloons

Recent findings of the catastrophic balloon failures investigation in the U.S.A. indicate that very large gross inflations, in balloons using present design philosophy, over-stress currently available materials. External caps are proposed as an economic approach to reducting those stresses to an acceptable level.     

Power supplies for long duration balloon flights

Long duration balloon flights require more electrical power than can be carried in primary batteries. This paper provides design information for selecting rechargeable batteries and charging systems. Solar panels for recharging batteries are discussed, with particular emphasis on cells mounting suitable for balloon flights and panel orientation for maximum power collection. Since efficient utilization of power is so important, modern DC to DC power conversion techniques are presented.On short flights of 1 day or less, system designers have not been greatly concerned with battery weight. But, with the advent of long duration balloon flights using superpressure balloons, anchor balloon systems, and RACOON balloon techniques, power supplies and their weight become of prime importance. The criteria for evaluating power systems for long duration balloon flights is performance per unit weight. Instrumented balloon systems have flown 44 days. For these very long duration flights, batteries recharged from solar cells are the only solution. For intermediate flight duration, say less than 10 days, the system designer should seriously consider using primary cells.     

Systems for long duration flights

This paper describes the systems for long duration flights developed in Japan for scientific observations. Much efforts have been expended to evolve systems for long duration flights in Japan, by controlling the balloon trajectories with a knowledge of wind pattern at high altitudes over Japan. These systems called “Cycling Balloon”, “Boomerang Balloon” and “New Boomerang Balloon” have been successfully used for the observations by keeping the balloons close to the balloon station.“Relay Balloon” is another system to extend the telemetry range by using an additional balloon as a relay station to link the telemetry from the main balloon.Some detailes of the exhaust valve, ascent meter and automatic level control devices used for the balloon control are also described in the paper.     

Advances in long duration,high altitude flights

During the past two decades there have been many significant advances made in the state-of-the-art of scientific ballooning. High altitude long duration flights, of moderate to heavy payloads, however, have proven to be the one requirement of the scientific community that has been the most difficult to meet. Conventional and cryogenic ballasting systems, super pressure balloons and hybrid balloon systems are some of the approaches that have been taken to maintain experiments at altitude for extended periods of time. The results of those development efforts and various methods of data retrieval will be discussed.     

Synopsis of troposphere and lower stratosphere

The use of different types of balloons for the investigation of the troposphere and lower stratosphere is reviewed with a special emphasis on the application for the next 10 years. The instrumentation currently flown aboard balloons or under development is described. Some possible scientific objectives of such balloon experiments are presented. The specific applications of the different types of balloons available within the next few years for scientific flights are discussed.     

Transient thermal behavior of stratospheric balloons at float conditions

The prediction of the thermal behavior of stratospheric balloons under varying environmental conditions is one of the key issues in the design and flight test of balloons. In this paper, a three-dimensional transient thermal model is developed to predict the thermal behavior of spherical stratospheric balloons. The diurnal variations of the skin and lifting gas temperatures at float conditions are discussed in detail. The further studies on the thermal behavior of stratospheric balloons are presented also.     

Ballooning activities in Japan

The Scientific Balloon Center of ISAS/JAXA has carried out two balloon campaigns at Sanriku, Iwate, Japan every year. Ten to twelve balloon vehicles are launched annually for scientific and engineering experiments. Since 2005, a Brazilian balloon campaign has also been conducted in cooperation with INPE. In the 2006 Brazilian campaign, large and heavy payloads up to 1500 kg for astronomy will be launched. New generation balloons, such as super-pressure balloons and high-altitude balloons with ultra-thin films, are being developed. The current status and prospect of the Japanese scientific ballooning are discussed.     

Synoptic studies of the middle atmosphere using balloons

During the Middle Atmosphere Program, 1982–1985, balloons will play a central role in gathering stratospheric, chemical, and dynamical data. This paper discusses some of the unique aspects of balloons as tools for probing the middle atmosphere, and suggests some directions for future projects and enhanced capabilities that would improve their utility in future investigations.     

Venus atmospheric platform options revisited

Various balloon systems intended as scientific platforms to float in the atmosphere of Venus at altitudes between about 35 and 65 km are briefly reviewed. Previous predictions of the altitude oscillations of balloons filled with helium gas and water vapor are largely confirmed through numerical simulation and analysis. The need for refined thermal modelling is emphasised. Several novel technical concepts are introduced. It is concluded that phase change balloons would be more suitable than non-condensing super pressure gas balloons when repeated altitude excursions are a mission requirement.     

Vertical sounding balloons for stratospheric photochemistry

Vertical sounding balloons are unique tools for stratospheric photochemistry investigations. An example of the use of a vertically piloted gas balloon for nitrogen dioxide diurnal variation search is presented. Improvements of such a method with the use of montgolfieres (hot air balloons) are proposed.     

The high altitude student platform (HASP) for student-built payloads

An outstanding issue with aerospace workforce development is what should be done at the university level to attract and prepare undergraduates for an aerospace career. One approach adopted by many institutions is to lead students through the design and development of small payloads (less than about 500 grams) that can be carried up to high altitude (around 30 km) by a latex sounding balloon. This approach has been very successful in helping students to integrate their content knowledge with practical skills and to understand the end-to-end process of aerospace project development. Sounding balloons, however, are usually constrained in flight duration (∼30 min above 24 km) and payload weight, limiting the kinds investigations that are possible. Student built picosatellites, such as CubeSats, can be placed in low Earth orbit removing the flight duration constraint, but the delays between satellite development and launch can be years. Here, we present the inexpensive high altitude student platform (HASP) that is designed to carry at least eight student payloads at a time to an altitude of about 36 km with flight durations of 15–20 h using a small zero-pressure polyethylene film balloon. This platform provides a flight capability greater than sounding balloons and can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. The HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. HASP is lightweight, has simple mission requirements providing flexibility in the launch schedule, will provide a flight test opportunity at the end of each academic year.     

The development of plastic,zero pressure balloon design since 1945

There have been four major thrusts in plastic, zero pressure balloon design in the U.S. since the late 1940's. First, the pioneer balloonists made designs according to geometric shapes. When these balloons began to fail, a study at the University of Minnesota produced the first mathematical model for determining the proper design for “natural shaped” balloons. With the advent of high speed digital computing came the “Sigma” tables of the 1960's. When computers became more widespread and inexpensive, direct or “full-sized” designs began to be used. Now, with the problems involved in flying heavy payloads (greater than 400 lbs) and super pressure balloons, a new tool has become available to the balloon designer. An inexpensive stress analysis code is available but is as yet unproven.     

Un dispositif experimental utilisant des ballons plafonnants pour l'etude de la couche limite atmospherique

This paper presents a new system of constant volume balloons used to study the dynamical and thermodynamical properties of the tropospheric boundary layer. The system allows to simultaneously localize up to 30 balloons and to observe thermodynamical characteristics of the air during their flight inside the boundary layer. Each balloon is equipped with a radar reflector and a sounding system giving information each second on pressure, humidity and temperature by sequential emissions which are received at a ground station. The trajectories of balloons are obtained by a non-tracking S-band radar where a special hardware processing unit allows to real time cancellation of most ground clutter. A complete set of the balloons positions is obtained every two or three minutes.The system was tested in October 1984 during a field experiment in the south of France. Results of the experimental procedure and of the quality of the balloon, radar and sounding capabilities are given. The scientific use of constant volume balloons in order to study the atmospheric boundary layer is examined.     

PEGASO: An ultra light long duration stratospheric payload for polar regions flights

Stratospheric balloons are powerful and affordable tools for a wide spectrum of scientific investigations that are carried out at the stratosphere level. They are less expensive compared to satellite projects and have the capability to lift payloads from a few kilograms to a couple of tons or more, well above the troposphere, for more than a month. Another interesting feature of these balloons, which is not viable in satellites, is the short turnaround time, which enables frequent flights.     

Cleft formation in pumpkin balloons

NASA’s development of a large payload, high altitude, long duration balloon, the Ultra Long Duration Balloon, centers on a pumpkin shape super-pressure design. Under certain circumstances, it has been observed that a pumpkin balloon may be unable to pressurize into the desired cyclically symmetric equilibrium configuration, settling into a distorted, undesired state instead. Success of the pumpkin balloon for NASA requires a thorough understanding of the phenomenon of multiple stable equilibria and developing of means for the quantitative assessment of design measures that prevent the occurrence of undesired equilibrium. In this paper, we will use the concept of stability to classify cyclically symmetric equilibrium states at full inflation and pressurization. Our mathematical model for a strained equilibrium balloon, when applied to a shape that mimics the Phase IV-A balloon of Flight 517, predicts instability at float. Launched in Spring 2003, this pumpkin balloon failed to deploy properly. Observations on pumpkin shape type super-pressure balloons that date back to the 1980s suggest that within a narrowly defined design class of pumpkin shape super-pressure balloons where individual designs are fully described by the number of gores n_g and by a single measure of the bulging gore shape, the designs tend to become more vulnerable with the growing number of gores and with the diminishing size of the bulge radius r_B Weight efficiency considerations favor a small bulge radius, while robust deployment into the desired cyclically symmetrical configuration becomes more likely with an increased bulge radius. In an effort to quantify this dependency, we will explore the stability of a family of balloon shapes parametrized by (n_g, r_B) which includes a design that is very similar, but not identical, to the balloon of Flight 517. In addition, we carry out a number of simulations that demonstrate other aspects related to multiple equilibria of pumpkin balloons.     

Scientific ballooning in Japan

Activities in scientific ballooning in Japan during 1998–1999 are reported. The total number of scientific balloons flown in Japan in 1998 and 1999 was sixteen, eight flights in each year. The scientific objectives were observations of high energy cosmic electrons, air samplings at various altitudes, monitoring of atmospheric ozone density, Galactic infrared observations, and test flights of new type balloons. Balloon expeditions were conducted in Antarctica by the National Institute of Polar Research, in Russia, in Canada and in India in collaboration with foreign countries' institutes to investigate cosmic rays, Galactic infrared radiation, and Earth's atmosphere. There were three flights in Antarctica, four flights in Russia, three flights in Canada and two flights in India. Four test balloons were flown for balloon technology, which included pumpkin-type super-pressure balloon and a balloon made with ultra-thin polyethylene film of 3.4 μm thickness.