Venus surface power and cooling systems

A mission to the surface of Venus would have high scientific value, but most electronic devices and sensors cannot operate at the 450 °C ambient surface temperature of Venus. Power and cooling systems were analyzed for Venus surface operation. A radioisotope power and cooling system was designed to provide electrical power for a probe operating on the surface of Venus. For a mission duration of substantial length, the use of thermal mass to maintain an operable temperature range is likely impractical, and active refrigeration may be required to keep components at a temperature below ambient. Due to the high thermal convection of the high-density atmosphere, the heat rejection temperature was assumed to be at a 500 °C radiator temperature, 50 °C above ambient. The radioisotope Stirling power converter designed produces a thermodynamic power output capacity of 478.1 W, with a cooling power of 100 W. The overall efficiency is calculated to be 23.36%. The mass of the power converter is estimated at approximately 21.6 kg.     

Aerobraking at Venus: A science and technology enabler

Venus remains one of the great unexplored planets in our solar system, with key questions remaining on the evolution of its atmosphere and climate, its volatile cycles, and the thermal and magmatic evolution of its surface. One potential approach toward answering these questions is to fly a reconnaissance mission that uses a multi-mode radar in a near-circular, low-altitude orbit of ∼400 km and 60–70° inclination. This type of mission profile results in a total mission delta-V of ∼4.4 km/s. Aerobraking could provide a significant portion, potentially up to half, of this energy transfer, thereby permitting more mass to be allocated to the spacecraft and science payload or facilitating the use of smaller, cheaper launch vehicles.Aerobraking at Venus also provides additional science benefits through the measurement of upper atmospheric density (recovered from accelerometer data) and temperature values, especially near the terminator where temperature changes are abrupt and constant pressure levels drop dramatically in altitude from day to night.Scientifically rich, Venus is also an ideal location for implementing aerobraking techniques. Its thick lower atmosphere and slow planet rotation result in relatively more predictable atmospheric densities than Mars. The upper atmosphere (aerobraking altitudes) of Venus has a density variation of 8% compared to Mars' 30% variability. In general, most aerobraking missions try to minimize the duration of the aerobraking phase to keep costs down. These short phases have limited margin to account for contingencies. It is the stable and predictive nature of Venus' atmosphere that provides safer aerobraking opportunities.The nature of aerobraking at Venus provides ideal opportunities to demonstrate aerobraking enhancements and techniques yet to be used at Mars, such as flying a temperature corridor (versus a heat-rate corridor) and using a thermal-response surface algorithm and autonomous aerobraking, shifting many daily ground activities to onboard the spacecraft. A defined aerobraking temperature corridor, based on spacecraft component maximum temperatures, can be employed on a spacecraft specifically designed for aerobraking, and will predict subsequent aerobraking orbits and prescribe apoapsis propulsive maneuvers to maintain the spacecraft within its specified temperature limits. A spacecraft specifically designed for aerobraking in the Venus environment can provide a cost-effective platform for achieving these expanded science and technology goals.This paper discusses the scientific merits of a low-altitude, near-circular orbit at Venus, highlights the differences in aerobraking at Venus versus Mars, and presents design data using a flight system specifically designed for an aerobraking mission at Venus. Using aerobraking to achieve a low altitude orbit at Venus may pave the way for various technology demonstrations, such as autonomous aerobraking techniques and/or new science measurements like a multi-mode, synthetic aperture radar capable of altimetry and radiometry with performance that is significantly more capable than Magellan.     

Venus Express: Scientific goals, instrumentation, and scenario of the mission

The first European mission to Venus (Venus Express) is described. It is based on a repeated use of the Mars Express design with minor modifications dictated in the main by more severe thermal environment at Venus. The main scientific task of the mission is global exploration of the Venusian atmosphere, circumplanetary plasma, and the planet surface from an orbiting spacecraft. The Venus Express payload includes seven instruments, five of which are inherited from the missions Mars Express and Rosetta. Two instruments were specially designed for Venus Express. The advantages of Venus Express in comparison with previous missions are in using advanced instrumentation and methods of remote sounding, as well as a spacecraft with a broad spectrum of capabilities of orbital observations.     

High precision composite pipes for SOLAR-B optical structures

The authors have been developing new high thermal conductivity and low moisture absorption composite pipes for high precision space optics applications on the Japanese Institute of Space and Astronautical Science (ISAS) SOLAR-B satellite.Pitch based K13C (Mitsubishi Chemical) high modulus and high conductivity graphite fiber, and EX1515 (Bryte Technology) low moisture absorption cyanate resin, were applied to the pipes.Thermal expansion of the composite pipes was designed to be zero and more uniform in the longitudinal direction in order to obtain long term dimensional stability in the space environment.Model pipes whose length was 500 mm were fabricated and evaluated for thermal and hygroscopic deformation in a new testing apparatus. Equivalent coefficient of thermal expansion of the model pipes was essentially zero (less than 0.1 ppm/°C) and standard deviation of these coefficients was 0.05 ppm/°C. Hygroscopic deformation of the model pipes was under representative conditions 7 ppm over 3 month. The excellent thermal and hygroscopic stability were verified. In addition, thermal conductivity of the model pipes was more than 200 W/(m · K).     

Technology-based design and scaling for RTGs for space exploration in the 100 W range

This paper presents the results of a study on design considerations for a 100 W radioisotope thermo-electric generator (RTG). Special emphasis has been put on designing a modular, multi-purpose system with high overall TRL levels and making full use of the extensive Russian heritage in the design of radioisotope power systems. The modular approach allowed insight into the scaling of such RTGs covering the electric power range from 50 to 200 W_e (EoL). The retained concept is based on a modular thermal block structure, a radiative inner-RTG heat transfer and using a two-stage thermo-electric conversion system.     

RF communications subsystem for the Radiation Belt Storm Probes mission

The NASA Radiation Belt Storm Probes (RBSP) mission, currently in Phase B, is a two-spacecraft, Earth-orbiting mission, which will launch in 2012. The spacecraft's S-band radio frequency (RF) telecommunications subsystem has three primary functions: provide spacecraft command capability, provide spacecraft telemetry and science data return, and provide accurate Doppler data for navigation. The primary communications link to the ground is via the Johns Hopkins University Applied Physics Laboratory's (JHU/APL) 18 m dish, with secondary links to the NASA 13 m Ground Network and the Tracking and Data Relay Spacecraft System (TDRSS) in single-access mode. The on-board RF subsystem features the APL-built coherent transceiver and in-house builds of a solid-state power amplifier and conical bifilar helix broad-beam antennas. The coherent transceiver provides coherency digitally, and controls the downlink data rate and encoding within its field-programmable gate array (FPGA). The transceiver also provides a critical command decoder (CCD) function, which is used to protect against box-level upsets in the C&DH subsystem. Because RBSP is a spin-stabilized mission, the antennas must be symmetric about the spin axis. Two broad-beam antennas point along both ends of the spin axis, providing communication coverage from boresight to 70°. An RF splitter excites both antennas; therefore, the mission is designed such that no communications are required close to 90° from the spin axis due to the interferometer effect from the two antennas. To maximize the total downlink volume from the spacecraft, the CCSDS File Delivery Protocol (CFDP) has been baselined for the RBSP mission. During real-time ground contacts with the APL ground station, downlinked files are checked for errors. Handshaking between flight and ground CFDP software results in requests to retransmit only the file fragments lost due to dropouts. This allows minimization of RF link margins, thereby maximizing data rate and thus data volume.     

Venus Express—Science observations experience at Venus

The Venus Express mission is the European Space Agency's (ESA) first spacecraft at Venus. It was launched in November 2005 by a Soyuz–Fregat launcher and arrived at Venus in April 2006. The mission covers a broad range of scientific goals including physics, chemistry, dynamics and structure of the atmosphere as well as atmospheric interaction with the surface and several aspects of the surface itself. Furthermore, it investigates the plasma environment and interaction of the solar wind with the atmosphere and escape processes.One month after the arrival at Venus the Venus Express spacecraft started routine science operations. Since then Venus Express has been observing Venus every day for more than one year continuously making new discoveries.In order to ensure that all the science objectives are fulfilled the Venus Express Science Operations Centre (VSOC) has the task of coordinating and implementing the science operations for the mission. During the first year of Venus observations the VSOC and the experiment teams gained a lot of experience in how to make best use of the observation conditions and payload capabilities. While operating the spacecraft in orbit we also acquired more knowledge on the technical constraints and more insight in the science observations and their results.As the nominal mission is coming to an end, the extended mission will start from October 2007. The Extended Science Mission Plan was developed taking into account the lessons learned. At the same time new observations were added along with specific fine-tuned observations in order to complete the science objectives of the mission.This paper will describe how the previous observations influence the current requirements for the observations around Venus today and how they influence the observations in the mission extension. Also it will give an overview of the Extended Science Mission Plan and its challenges for the future observations.     

Self-perspiration garment for extravehicular activity improves skin cooling effects without raising humidity

Introduction

The current U.S. extravehicular activity (EVA) suit in space includes liquid cooling and ventilation garment (LCVG) to control thermal condition. Tubes knitted in LCVG for flowing water interrupt evaporation of perspiration, and astronauts feel discomfort. In the present study, we hypothesized that a self-perspiration garment would effectively lower the skin temperature without raising humidity in the garment. Thus, we developed and examined the effects of the garment.

Methods

Eight healthy subjects were studied with a cyclic ergometer of 30, 60 90 and 120 W loading for 3 min each. Skin temperature and humidity on the back were measured continuously. Subjects wore and tested three types of garments i.e., a spandex wear without any cooling device (Normal), a simulated LCVG (s-LCVG) or the spandex wear knitted a vinyl tube for flowing water, and the spandex wear with a tube, which flows water and self-perspiration with oozing water for evaporative cooling (SPEC).

Results

All measurements were reached to steady state 2–3 min after the setting. The s-LCVG decreased skin temperature 0.39±0.14 °C during 12 min of cooling. With SPEC, skin temperature did not decrease significantly until 6–9 min after starting the cooling. However, the temperature decreased rapidly and significantly after that, and finally decreased 1.59±0.32 °C. Humidity in the SPEC was significantly lower than that in s-LCVG.

Discussion

SPEC was effective for lowering skin temperature without raising humidity in the garment. The concept is expected to use as a better cooling system during EVA.     

Heat storage and electricity generation in the Moon during the lunar night

One of the biggest challenges of the exploration of the Moon is the survival of the crew and the lunar assets during the lunar night. The environmental conditions on the lunar surface and its cycle, with long periods of darkness, make any long mission in need of specific amounts of heat and electricity to be successful. We have analyzed two different systems to produce heat and electricity on the Moon's surface. The first system consists of Thermal Wadis, sources of thermal power that can be used to supply heat to protect the exploration systems from the extreme cold during periods of darkness. Previous results showed that Wadis can supply enough heat to keep lunar devices such as rovers above their minimum operating temperature (approximately 243 K). The second system studied here is the Thermal Energy Storage (TES), which is able to run a heat engine during the lunar night to produce electricity. When the Sun is shining on the Moon's surface, the system can run the engine directly using the solar power and simultaneously heat a thermal mass. This thermal mass is used as a high temperature source to run the heat engine during the night. We present analytical and numerical calculations for the determination of an appropriate thermal mass for the TES system.     

无载荷舱航空相机的热控设计与试验验证

为保证航空相机在平流层空间热环境下稳定运行,对无载荷舱的航空相机进行热设计和验证.基于20 km海拔高度下相机外部的对流及辐射环境特点,采用一维对称平板测试法确定选取多层隔热组件作为相机蒙皮材料,选取聚氨酯泡沫作为隔热填充材料.对载荷相机进行热控系统设计,并利用有限元软件分析极端工况下相机的温度场分布,最终设计热控总功...     

Optimal control laws for heliocentric transfers with a magnetic sail

A magnetic sail is an advanced propellantless propulsion system that uses the interaction between the solar wind and an artificial magnetic field generated by the spacecraft, to produce a propulsive thrust in interplanetary space. The aim of this paper is to collect the available experimental data, and the simulation results, to develop a simplified mathematical model that describes the propulsive acceleration of a magnetic sail, in an analytical form, for mission analysis purposes. Such a mathematical model is then used for estimating the performance of a magnetic sail-based spacecraft in a two-dimensional, minimum time, deep space mission scenario. In particular, optimal and locally optimal steering laws are derived using an indirect approach. The obtained results are then applied to a mission analysis involving both an optimal Earth–Venus (circle-to-circle) interplanetary transfer, and a locally optimal Solar System escape trajectory. For example, assuming a characteristic acceleration of 1 mm/s², an optimal Earth–Venus transfer may be completed within about 380 days.     

Hypothetical flora and fauna of Venus

Hypothetical habitability of some of extrasolar planets is a fundamental question of science. Some of exoplanets possess physical conditions close to those of Venus. Therefore, the planet Venus, with its dense and hot (735 K) oxygen-free atmosphere of CO₂, having a high pressure of 9.2 MPa at the surface, can be a natural laboratory for this kind of studies. The only existing data on the planet׳s surface are still the results obtained by the Soviet VENERA landers in the 1970s and 1980s. The TV experiments of Venera-9 and 10 (October, 1975) and Venera-13 and 14 (March, 1982) delivered 41 panoramas of Venus surface (or their fragments). There have not been any similar missions to Venus in the subsequent 39 and 32 years. In the absence of new landing missions to Venus, the VENERA panoramas have been re-processed. The results of these missions are studied anew. A dozen of relatively large objects, from a decimeter to half a meter in size, with an unusual morphology have been found which moved very slowly or changed slightly their shape. Their emergence by chance could hardly be explained by noise. Certain unusual findings that have similar structure were found in different areas of the planet. This paper presents the last results obtained of a search for hypothetical flora and fauna of Venus.     

Low cost planetary exploration: surrey lunar minisatellite and interplanetary platform missions

In order to meet the growing global requirement for affordable missions beyond Low Earth Orbit, two types of platform are under design at the Surrey Space Centre. The first platform is a derivative of Surrey's UoSAT-12 minisatellite, launched in April 1999 and operating successfully in-orbit. The minisatellite has been modified to accommodate a propulsion system capable of delivering up to 1700 m/s delta-V, enabling it to support a wide range of very low cost missions to LaGrange points, Near-Earth Objects, and the Moon. A mission to the Moon - dubbed “MoonShine” - is proposed as the first demonstration of the modified minisatellite beyond LEO. The second platform - Surrey's Interplanetary Platform - has been designed to support missions with delta-V requirements up to 3200 m/s, making it ideal for low cost missions to Mars and Venus, as well as Near Earth Objects (NEOs) and other interplanetary trajectories. Analysis has proved mission feasibility, identifying key challenges in both missions for developing cost-effective techniques for: spacecraft propulsion; navigation; autonomous operations; and a reliable safe mode strategy. To reduce mission risk, inherently failure resistant lunar and interplanetary trajectories are under study. In order to significantly reduce cost and increase reliability, both platforms can communicate with low-cost ground stations and exploit Surrey's experience in autonomous operations. The lunar minisatellite can provide up to 70 kg payload margin in lunar orbit for a total mission cost US$16–25 M. The interplanetary platform can deliver 20 kg of scientific payload to Mars or Venus orbit for a mission cost US$25–50 M. Together, the platforms will enable regular flight of payloads to the Moon and interplanetary space at unprecedented low cost. This paper outlines key systems engineering issues for the proposed Lunar Minisatellite and interplanetary Platform Missions, and describes the accommodation and performance offered to planetary payloads.     

Power system design of ESMO

The European Student Moon Orbiter (ESMO) spacecraft is a student-built mini satellite being designed for a mission to the Moon. Designing and launching mini satellites are becoming a current trend in the space sector since they provide an economic way to perform innovative scientific experiments and in-flight demonstration of novel space technologies. The generation, storage, control, and distribution of the electrical power in a mini satellite represents unique challenges to the power engineer since the mass and volume restrictions are very stringent. Regardless of these problems, every subsystem and payload equipment must be operated within their specified voltage band whenever they required to be turned on. This paper presents the preliminary design of a lightweight, compact, and reliable power system for ESMO that can generate 720 W. Some of the key components of the EPS include ultra triple-junction (UTJ) GaAs solar cells controlled by maximum power point trackers, and high efficiency Li-ion secondary batteries recharged in parallel.     

Chandrayaan-1 mission to the Moon

Chandrayaan-1 is the first Indian planetary exploration mission that will perform remote sensing observation of the Moon to further our understanding about its origin and evolution. Hyper-spectral studies in the 0.4– region using three different imaging spectrometers, coupled with a low energy X-ray spectrometer, a sub-keV atom analyzer, a 3D terrain mapping camera and a laser ranging instrument will provide data on mineralogical and chemical composition and topography of the lunar surface at high spatial resolution. A low energy gamma ray spectrometer and a miniature imaging radar will investigate volatile transport on lunar surface and possible presence of water ice in the polar region. A radiation dose monitor will provide an estimation of energetic particle flux en route to the Moon as well as in lunar orbit. An impact probe carrying a mass spectrometer will also be a part of the spacecraft. The 1 ton class spacecraft will be launched by using a variant of flight proven indigenous Polar Satellite Launch Vehicle (PSLV-XL). The spacecraft will be finally placed in a 100 km circular polar orbit around the Moon with a planned mission life of two years.     

Deployment history and design considerations for space reactor power systems

The history of the deployment of nuclear reactors in Earth orbits is reviewed with emphases on lessons learned and the operation and safety experiences. The former Soviet Union's “BUK” power systems, with SiGe thermoelectric conversion and fast neutron energy spectrum reactors, powered a total of 31 Radar Ocean Reconnaissance Satellites (RORSATs) from 1970 to 1988 in 260 km orbit. Two of the former Soviet Union's TOPAZ reactors, with in-core thermionic conversion and epithermal neutron energy spectrum, powered two Cosmos missions launched in 1987 in ～800 km orbit. The US’ SNAP-10A system, with SiGe energy conversion and a thermal neutron energy spectrum reactor, was launched in 1965 in 1300 km orbit. The three reactor systems used liquid NaK-78 coolant, stainless steel structure and highly enriched uranium fuel (90–96 wt%) and operated at a reactor exit temperature of 833–973 K. The BUK reactors used U-Mo fuel rods, TOPAZ used UO₂ fuel rods and four ZrH moderator disks, and the SNAP-10A used moderated U-ZrH fuel rods. These low power space reactor systems were designed for short missions (～0.5 kW_e and ～1 year for SNAP-10A, <3.0 kW_e and <6 months for BUK, and ～5.5 kW_e and up to 1 year for TOPAZ). The deactivated BUK reactors at the end of mission, which varied in duration from a few hours to ～4.5 months, were boosted into ～800 km storage orbit with a decay life of more than 600 year. The ejection of the last 16 BUK reactor fuel cores caused significant contamination of Earth orbits with NaK droplets that varied in sizes from a few microns to 5 cm. Power systems to enhance or enable future interplanetary exploration, in-situ resources utilization on Mars and the Moon, and civilian missions in 1000–3000 km orbits would generate significantly more power of 10's to 100's kW_e for 5–10 years, or even longer. A number of design options to enhance the operation reliability and safety of these high power space reactor power systems are presented and discussed.     

V型皱褶芯材夹层板对流换热性能评价及优化

为考察主动冷却式一体化热防护结构用V型皱褶芯材夹层结构的性能，文章采用Fluent软件模拟受恒定热流载荷皱褶芯材夹层板在强制对流条件下的传热过程，分析其换热特性和流道内流体流动规律；并在分析皱褶芯材夹层板中正三角和倒三角2种流道换热性能差异的基础上，提出相邻流道流向相反的改进方案。该方案可提高冷却剂的利用率，使结构温度分布更加均匀。相比于具有相同几何参数的波纹芯材夹层板，皱褶芯材夹层板具有更好的换热性能，但同时以更大的当量密度和进出口压降损失为代价。比较几种常用的热效率指标，并定义了一种同时考虑换热性能、泵功率和结构质量的热效率指标，再分别以不同的热效率指标为目标函数，对皱褶芯材的几何参数L、W和S进行初步优化设计。     

Venus, Mars, and the ices on Mercury and the moon: astrobiological implications and proposed mission designs

Venus and Mars likely had liquid water bodies on their surface early in the Solar System history. The surfaces of Venus and Mars are presently not a suitable habitat for life, but reservoirs of liquid water remain in the atmosphere of Venus and the subsurface of Mars, and with it also the possibility of microbial life. Microbial organisms may have adapted to live in these ecological niches by the evolutionary force of directional selection. Missions to our neighboring planets should therefore be planned to explore these potentially life-containing refuges and return samples for analysis. Sample return missions should also include ice samples from Mercury and the Moon, which may contain information about the biogenic material that catalyzed the early evolution of life on Earth (or elsewhere). To obtain such information, science-driven exploration is necessary through varying degrees of mission operation autonomy. A hierarchical mission design is envisioned that includes spaceborne (orbital), atmosphere (airborne), surface (mobile such as rover and stationary such as lander or sensor), and subsurface (e.g., ground-penetrating radar, drilling, etc.) agents working in concert to allow for sufficient mission safety and redundancy, to perform extensive and challenging reconnaissance, and to lead to a thorough search for evidence of life and habitability.     

Intelsat's next generation satellite for the Americas

In order to meet the growing demand for high performance C- and Ku-Band services in the Americas, INTELSAT contracted with Astrium in February 2000 to procure a high capacity communications spacecraft for its 310°E operational location. The spacecraft platform is based on Astrium's next generation platform, the Eurostar 3000. Several new technologies such as integrated Data Handling System, Plasma Propulsion System, etc. are integral features of this platform. The communication payload comprises 36 C-Band and 20 high power Ku-Band transponders. The beam coverages are tailored for the 310°E orbital location and are implemented using a hybrid shaped antenna design approach, where multiple C-Band coverages are generated from a single shaped reflector utilizing a pair of Tx/Rx feed horns for each coverage. The Ku-Band coverages are generated by the classical dual Gregorian shaped reflector antenna design approach. With a total dry mass on the order of 2650 kg and a separated launch mass of 5400 kg, the spacecraft is compatible with most of the available launch vehicles providing mission life of greater than 13 years. The paper will provide technical details of the spacecraft.