An Analysis of the Low-Frequency Component in Measurements of Angular Velocity and Microacceleration onboard the Foton-12 Satellite

We compare the results of two methods used to determine the angular velocity of the Foton-12 satellite and the low-frequency component of microaccelerations onboard it. The first method is based on reconstruction of the satellite's rotational motion using the data of onboard measurements of the strength of the Earth's magnetic field. The motion (time dependence of the orientation parameters and angular velocity) was found from the condition of best approximation of the measurement data by the functions calculated along the solutions to equations of attitude motion of the satellite. The solutions found were used to calculate the quasistatic component of microaccelerations at certain points of the satellite, in particular, at the point of location of an accelerometer of the QSAM system. Filtration of the low-frequency component of the angular velocity and microacceleration from the data of measurements by a sensor of angular velocity and by the accelerometer of this system served as a second method. The filtration was made using the discrete Fourier series. A spectral analysis of the functions representing the results of determining the angular velocity and microacceleration by both methods is performed. Comparing the frequencies and amplitudes of the harmonic component of these functions allowed us to estimate the accuracy of measurements made by the QSAM system in the low-frequency range.     

Reconstruction of spacecraft rotational motion using a Kalman filter

Quasi-static microaccelerations of four satellites of the Foton series (nos. 11, 12, M-2, M-3) were monitored as follows. First, according to measurements of onboard sensors obtained in a certain time interval, spacecraft rotational motion was reconstructed in this interval. Then, along the found motion, microacceleration at a given onboard point was calculated according to the known formula as a function of time. The motion was reconstructed by the least squares method using the solutions to the equations of satellite rotational motion. The time intervals in which these equations make reconstruction possible were from one to five orbital revolutions. This length is increased with the modulus of the satellite angular velocity. To get an idea on microaccelerations and satellite motion during an entire flight, the motion was reconstructed in several tens of such intervals. This paper proposes a method for motion reconstruction suitable for an interval of arbitrary length. The method is based on the Kalman filter. We preliminary describe a new version of the method for reconstructing uncontrolled satellite rotational motion from magnetic measurements using the least squares method, which is essentially used to construct the Kalman filter. The results of comparison of both methods are presented using the data obtained on a flight of the Foton M-3.     

The Influence of Arrangement of Growth Setups onboard a Spacecraft on Microgravity Conditions of Experiments: An Example of Floating Zone Melting of InSb:Te onboard the Foton-3 Satellite

The results of experiments on the growth of InSb:Te by the floating zone melting in the Zona-4 setup during a flight of the Foton-3 satellite are discussed in comparison with the data on the microgravity situation typical for satellites of this type. When analyzing inhomogeneities in the crystals obtained, we reveal the frequencies corresponding to periodical variations of the impurity channel position (the facet effect), to interleaving of packs in which the growth layers are grouped, and to location of subgroups of the growth layers inside the packs. These frequencies are close to those discovered during measurements of low-frequency (quasistationary) microaccelerations (g) onboard the spacecraft Foton-8, Foton-10, Foton-11, and Foton-12. Calculated values of g at the place where the Zona-4 setup is installed confirm the possibility of impact of such g on the heat and mass transfer in the melt.     

Study of microaccelerations onboard the <Emphasis Type="Italic">International Space Station</Emphasis> with the DAKON-M convection sensor

The results of experiments with the DAKON-M convection sensor onboard the Russian orbital segment of the International Space Station are described. A comparison of the sensor measurements with the results of calculation of the quasistatic microacceleration component at the point of installation is made. For this comparison we have used three measurement intervals of the experiments in 2009, during which spacecraft were docked with the station, undocked from it, and actuation of jet engines of the attitude control system took place. When calculating microacceleration, we use the measurement data of the low-frequency MAMS accelerometer, installed on the American segment, and the telemetry data on the ISS rotational motion. This information allowed one to convert the MAMS measurements to the point of installation of the DAKON-M convection sensor. A comparison of sensor measurements with calculated microaccelerations showed sufficiently accurate coincidence between the calculated and measured data.     

Influence of Microaccelerations on the Impurity Distribution in the InSb:Te Crystals Grown in Orbital Flights by the Method of Floating Zone Melting

The periodicity of the structure of impurity heterogeneities in the longitudinal section of an indium antimonide monocrystal doped by tellurium (InSb:Te) is investigated. The monocrystal was grown by the method of floating zone melting onboard the Foton-3 satellite. It is shown that the frequencies of harmonic components of heterogeneities converted into the time region coincide with frequencies of microaccelerations in the range 0–0.005 Hz arising onboard the Foton satellites. This fact confirms the hypothesis stated previously that residual microaccelerations onboard the satellite were the cause of occurrence of indicated periodicities.     

Some Features of Vibrational Perturbations onboard the MirOrbital Station

A number of scientific and technical experiments were carried out and are still being carried out onboard the Mirorbital station in various fields: physics of fluids, space materials study, astrophysics, biotechnology, and so on. The quality and reliability of space experiments are essentially dependent on a knowledge of real microgravitational situation onboard a satellite, which essentially depends on vibrational perturbations. A lot of vibration processes studies have been done up to now on the Mirstation in the following lines of research: control of dynamic and exploitation regimes when carrying out biotechnological and technological experiments; determination of the contribution of different onboard systems and mechanisms to the total vibration perturbations power; and investigation of distributions of microacceleration levels and dynamics of vibration processes in different modules and segments of the orbital station. This paper presents the results of the analysis of vibration perturbations produced by some standard onboard Mirstation systems in a configuration when the KVANT-2 and KRISTALL modules were arranged along the yaw axis of the mainframe. It is shown that due to strong requirements for tolerable levels of the microaccelerations onboard the International Space Station (ISS), the investigations of microgravitational situation, as an integral part of the technological environment, now have a high priority.     

Low-Frequency Microaccelerations onboard the Foton-11 Satellite

We analyze the microacceleration measurements carried out onboard the Foton-11 satellite with the three-component accelerometer BETA. The microaccelerations were recorded virtually throughout the entire orbital flight of the Foton-11 satellite. The data obtained were analyzed in the following way. First they were used to determine the actual rotational motion of the satellite for several arbitrarily selected time intervals 4 h long. This problem was solved by constructing the approximation of the microacceleretation low-frequency component (previously determined from the data) by its calculated analog computed along the solutions to differential equations of rotational motion of the satellite. The approximation was made by the least squares method. As a result, those mathematical model parameters and the solutions to equations of motion were found that gave the best consistency of the microacceleretation low-frequency component and its calculated analog. Then the spectral analysis of the low-frequency component and its calculated analog was made. It was shown that, although basic harmonics of these functions coincided sufficiently well, some harmonics of the low-frequency component failed to be interpreted in terms of the satellite's rotational motion.     

Analysis of Low-Frequency Microaccelerations onboard the Foton-11Satellite

The method and the results of investigating the low-frequency component of microaccelerations onboard the Foton-11satellite are presented. The investigation was based on the processing of data of the angular velocity measurements made by the German system QSAM, as well as the data of measurements of microaccelerations performed by the QSAM system and by the French accelerometer BETA. The processing was carried out in the following manner. A low-frequency (frequencies less than 0.01 Hz) component was selected from the data of measurements of each component of the angular velocity vector or of the microacceleration, and an approximation was constructed of the obtained vector function by a similar function that was calculated along the solutions to the differential equations of motion of the satellite with respect to its center of mass. The construction was carried out by the least squares method. The initial conditions of the satellite motion, its aerodynamic parameters, and constant biases in the measurement data were used as fitting parameters. The time intervals on which the approximation was constructed were from one to five hours long. The processing of the measurements performed with three different instruments produced sufficiently close results. It turned out to be that the rotational motion of the satellite during nearly the entire flight was close to the regular Eulerian precession of the axially symmetric rigid body. The angular velocity of the satellite with respect to its longitudinal axis was about 1 deg/s, while the projection of the angular velocity onto the plane perpendicular to this axis had an absolute value of about 0.2 deg/s. The magnitude of the quasistatic component of microaccelerations in the locations of the accelerometers QSAM and BETA did not exceed 5 × 10^–5–10^–4m/s²for the considered motion of the satellite.     

Estimation of dynamic characteristics of the <Emphasis Type="Italic">International Space Station</Emphasis> from measurements of microaccelerations

We describe the results of determining the mass of the International Space Station using the data of MAMS accelerometer taken during correction of the station orbit on August 20, 2004. The correction was made by approach and attitude control engines (ACE) of the Progress transporting spacecraft. The engines were preliminary calibrated in an autonomous flight using the onboard device for measuring apparent velocity increment. The method of calibration is described and its results are presented. The error in station mass determination is about 1%. The same data of MAMS and similar data obtained during the orbit correction on August 26, 2004 were used for the analysis of high-frequency vibrations of the station mainframe caused by operation of the ACE of Progress. Natural frequencies of the ACE are determined. They lie in the frequency band 0.024–0.11 Hz. ACE operation is demonstrated to result in a substantial increase of microaccelerations onboard the station in the frequency range 0–1 Hz. The frequencies are indicated at which disturbances increase by more than an order of magnitude. The study described was carried out as a part of the Tensor technological experiment.     

Measurement of the Quasistatic Component of Microaccelerations Using a Convection Sensor onboard a Satellite

The problem of the interpretation of measurements made by means of a convection sensor is considered. The sensor is a cubic chamber filled by a viscous fluid (gas). Fixed and unequal temperatures are maintained on two opposite sides of the cube; the other sides are perfect heat conductors. Two differential thermocouples are placed inside the chamber to measure the temperature difference at two pairs of fixed points. The sensor is mounted aboard the Earth's satellite. Mathematical models of various degrees of complexity are proposed which describe processes of heat and mass transfer under the action of a quasistatic component of microaccelerations. The results of mathematical simulation of the data of sensor thermocouples presenting a response to the real quasistatic component of microaccelerations which took place aboard the Mirstation are given. It is shown that under usual conditions of an orbital mission the sensor presents a linear low-frequency filter. By combining the data of several identical sensors, tightly arranged and oriented in a certain way, it is possible to measure low-frequency components of the angular acceleration of the satellite and linear microaccelerations at the point of the sensor position.     

Determination of quasi-static microaccelerations onboard a satellite using video images of moving objects

A space experiment aimed at determination of quasi-static microaccelerations onboard an artificial satellite of the Earth using video images of the objects executing free motion is considered. The experiment was carried out onboard the Foton M-3 satellite. Several pellets moved in a cubic box fixed on the satellite’s mainframe and having two transparent adjacent walls. Their motion was photographed by a digital video camera. The camera was installed facing one of the transparent walls; a mirror was placed at an angle to another transparent wall. Such an optical system allowed us to have in a single frame two images of the pellets from differing viewpoints. The motion of the pellets was photographed on time intervals lasting 96 s. Pauses between these intervals were also equal to 96 s. A special processing of a separate image allowed us to determine coordinates of the pellet centers in the camera’s coordinate system. The sequence of frames belonging to a continuous interval of photography was processed in the following way. The time dependence of each coordinate of every pellet was approximated by a second degree polynomial using the least squares method. The coefficient of squared time is equal to a half of the corresponding microacceleration component. As has been shown by processing made, the described method of determination of quasi-static microaccelerations turned out to be sufficiently sensitive and accurate.     

Experimental investigation of the modes of operation of uncontrolled attitude motion of the Progress spacecraft

Results of in-flight tests of three modes of uncontrolled attitude motion of the Progress spacecraft are described. These proposed modes of experiments related to microgravity are as follows: (1) triaxial gravitational orientation, (2) gravitational orientation of the rotating satellite, and (3) spin-up in the plane of the orbit around the axis of the maximum moment of inertia. The tests were carried out from May 24 to June 1, 2004 onboard the spacecraft Progress M1-11. The actual motion of this spacecraft with respect to its center of mass, in the above-mentioned modes, was determined by telemetric information about an electric current tapped off from solar batteries. The values of the current obtained during a time interval of several hours were processed jointly using the least squares method by integration of the equations of the spacecraft’s attitude motion. The processing resulted in estimation of the initial conditions of motion and of the parameters of mathematical models used. For the obtained motions the quasi-static component of microaccelerations was computed at a point onboard, where installation of experimental equipment is possible.     

Experiments with the DAKON-M convection sensor

We have described an express technique for processing the results of experiments with a DAKON-M convection sensor on board the Service Module of the International Space Station (ISS) in 2011. The technique uses a certain rule to compare the sensor measurements with the calculated data on the quasistatic component of microacceleration at the point of installation. The sensor experiments have been conducted during shuttle docking and undocking, when low-frequency microaccelerations on the ISS were significant. The microaccelerations have been calculated using measurement data of the MAMS low-frequency accelerometer installed in the Lab module and the telemetry data on the ISS rotational motion. This has made it possible to convert the MAMS measurement data to the DAKON-M convection sensor installation point. A comparison of sensor readings with calculated microaccelerations has revealed fairly good agreement between them.     

Mathematical Modeling of Convection in the DACON Sensor under Conditions of Real Space Flight

A mathematical model of the operation of the sensor of convection under ground and space conditions is described, and the results of modeling are compared to experimental data. A good agreement of the model and experiment is obtained for ground conditions. The sensor operation under conditions of a space flight is simulated using actual microaccelerations that took place onboard the Mirstation. Good sensitivity of the sensor to the measured components of acceleration is demonstrated. The results of simulation are compared to the results of space experiments carried out with the DACON instrument onboard the Mirstation.     

Realization of modes of satellite attitude motion with a small level of microaccelerations using electromechanical executive devices

Quasi-static microaccelerations are estimated for a satellite specially designed to perform space experiments in the field of microgravity. Three modes of attitude motion of the spacecraft are considered: passive gravitational orientation, orbital orientation, and semi-passive gravitational orientation. In these modes the lengthwise axis of the satellite is directed along the local vertical, while solar arrays lie in the orbit plane. The second and third modes are maintained using electromechanical executive devices: flywheel engines or gyrodynes. Estimations of residual microaccelerations are performed with the help of mathematical modeling of satellite’s attitude motion under the action of gravitational and aerodynamic moments, as well as the moment produced by the gyro system. It is demonstrated that all modes ensure rather low level of quasi-static microaccelerations on the satellite and provide for a fairly narrow region of variation for the vector of residual microacceleration. The semi-passive gravitational orientation ensures also a limited proper angular momentum of the gyro system.     

Determination of characteristic frequencies of elastic oscillations of the <Emphasis Type="Italic">International Space Station</Emphasis> construction

The results of investigating free oscillations of the International Space Station construction appearing during spacecraft docking and undocking are described. The study is carried out using the measurement data of the low-frequency MAMS accelerometer. Several intervals of measurements performed in 2005 and 2006 were chosen to be studied. For chosen intervals, only the data intervals corresponding to the process of free attenuation of the oscillations construction elements were analyzed. Characteristic frequencies of elastic oscillations of the station construction and attenuation coefficients corresponding to them are found. The comparative analysis of the results obtained for various docking ports (nodes) is carried out. The described study is performed as a part of the technical experiment “The ISS Environment” carried out onboard the station in accordance with the Russian program of scientific and engineering experiments.     

Quasistatic Microaccelerations onboard the Foton Satellite during Its Flight at High-Altitude Orbits

The level of quasistatic microaccelerations onboard the Foton-M satellite is predicted for its flights in two orbits: the planned orbit with the altitudes in perigee h = 262 km and in apogee h = 304 km and the orbit with h = 262 km and h = 350 km. The prediction is based on mathematical simulation of the satellite motion with respect to its center of mass under the action of gravitational and aerodynamic moments. The model is represented by the system of equations of the satellite rotational motion. Parameters of this system are chosen from the condition of coincidence of the motion of preceding Foton satellites (h 220 km and h 400 km) calculated using this model with the results of determination of actual rotational motion of the Foton-11 and Foton-12 satellites. With the help of the model thus calibrated, a calculation is made of the rotational motion of the Foton-M satellite and of the quasistatic microaccelerations onboard it. As is shown by the results of simulation, the use of the first and the second orbits will result in reductions of microaccelerations by 30% and 60%, respectively.     

Estimation of Low-Frequency Microaccelerations Onboard an Artificial Earth Satellite in the Solar Orientation Mode

Cosmic Research - Low-frequency microaccelerations are studied onboard an artificial Earth satellite designed for microgravity investigations in a low, near-circular orbit. The satellite has the...     

Detection and Prediction of Absorbed Radiation Doses from Solar Proton Fluxes onboard Orbital Stations

We consider cases of simultaneous detection of the absorbed doses produced by proton fluxes of powerful solar events onboard the Mir and ISS orbital stations and the Ekspress A3 geosynchronous satellite. Experimental data are analyzed using a software package that takes into account the energy spectra of protons at the Earth's orbit depending on the time of event evolution, as well as their penetration to near-earth orbits and through the protective shields of spacecraft. Based on a comparison of the experimental data of dosimeters with the calculation of absorbed doses under the action of solar proton events, we developed a method of estimating the effective thickness of the shielding of dosimeters and made some estimates. A possibility is considered for predicting the radiation hazard onboard orbital stations upon the appearance of solar proton events using dosimeter data from a geosynchronous orbit.