C_f/SiC复合材料与Ti合金的AgCuTi-W复合钎焊

本文利用AgCuTi-W复合钎料作中间层,在适当的工艺参数下真空钎焊Cf／SiC复合材料与Ti合金,利用SEM,EDS,XRD分析接头微观组织结构,利用剪切试验检测接头力学性能。研究结果表明：钎焊时,复合钎料中的Ti借助Cu-Ti液相与Cf／SiC复合材料反应,在Cf／SiC复合材料与连接层界面形成Ti3SiC2,Ti3Si和少量TiC化合物的混合反应层。复合钎料中的Cu与Ti合金中的Ti发生互扩散,在连接层与Ti合金界面形成不同成分的Cu—Ti化合物过渡层。钎焊后,形成W颗粒强化的致密复合连接层,W颗粒主要分布在Cu-Ti相中。W的加入缓解了接头的残余热应力,Cf／SiC／AgCuTi—W／TC4接头剪切强度明显高于CF／SiC／AgCuTi／TC4接头。     

快速凝固Al-Fe-MRE高温铝合金的研究

 研究快速凝固铝铁混合稀土高温铝合金的粉末制备及性能、粉末合金热成形、粉末合金的组织及性能的关系等。用氩气及氦气超音速雾化制得粉末获得的冷却速度为 5× 1 0 3～ 7× 1 0 6 K/s。用金相及扫描电镜观察粉末颗粒的形貌呈球形 ,粉末尺寸越小 ,组织越细。通过对挤压成形的Al-Fe-MRE粉末合金的室温、高温及热暴露试验 ,得到其力学性能及影响性能的因素     

钴基钎料钎焊K465合金大间隙接头组织与性能

采用Co45Ni Cr WB钴基钎料,预填FGH95镍基合金粉,在1220℃不同保温时间下对K465高温合金进行0.5 mm大间隙真空钎焊实验,研究钎缝组织构成及不同保温时间对钎缝组织与接头性能的影响。结果表明:钎缝组织由合金粉颗粒及颗粒间硼化物相构成,颗粒内为γ和γ'双相组织和少量小块状硼化相,颗粒间是高Cr,W和Nb的硼化物相;钎焊时随保温时间延长合金粉长大,化合物相合并长大;合金粉比例高、保温时间适当获得钎缝中化合物相细小弥散分布,对接头性能有利;钎焊保温30~60 min时接头持久性能较高。     

SABRE预冷器计算模型及其在整机模型中的应用

预冷器的性能对SABRE等预冷组合循环发动机具有重要影响,为实现发动机方案设计阶段预冷器的快速设计与评估,建立了预冷器准二维快速评估模型。将SABRE预冷器的几何结构简化为一个扇环形区域,沿径向和周向将该区域划分为二维节点。应用守恒方程及传热关联式完成单个节点计算,再求解节点矩阵的平衡方程组,计算内外流体特定节点上参数的二维分布,得到预冷器出口参数。将模型嵌入发动机总体性能程序中,实现了发动机设计及非设计点的预冷器性能计算的功能。与文献数据对比结果表明,预冷器模型传热计算误差小于5%,摩擦阻力误差小于10%。整机计算结果显示,Ma0~5范围内,预冷器空气侧温降范围为143K至932K,温降随飞行马赫数升高单调上升。预冷器传热有效度范围为0.896-0.945,空气侧总压恢复系数范围为0.852-0.904。     

高超声速航空发动机强预冷技术研究

高超声速飞行器动力是水平起降重复使用高超声速飞行器和单级入轨航天器能否成功的决定性因素,但目前仍面临许多问题,而强预冷是解决高超声速飞行器动力面临的问题的重要手段。本文对比分析了国外已有预冷发动机方案,并对其中优势最为明显的高超声速强预冷航空发动机的研究进展进行了总结。针对高超声速强预冷航空发动机中最为核心的紧凑快速强换热器,详细介绍了国内在其所涉及的微尺度流热耦合换热机理、流热耦合数值模拟、紧凑强换热器设计制造等方面的进展。国内外已有研究表明,强预冷高超声速航空发动机技术是一项具有非常巨大的潜在技术优势和前瞻性的共性技术,有望成为未来最适用的高超声速飞行器动力技术,值得引起关注并开展进一步的深入研究。     

The use of closed cycle coolers on space based observatories

Many proposed space based observations will rely on the use of closed cycle and passive cooling systems to provide the thermal environment for high sensitivity. The use of closed cycle mechanical coolers on space telescopes poses particular integration problems; some of these difficulties are discussed in this paper.One of the major problems envisaged is that of exported vibration. This problem, and that of the heat sinking required, can be alleviated by siting the compressors of the Stirling cycle precooler further from the displacer unit. The effect of the separation between the compressors and the displacer on the performance of the Stirling cycle precooler has been measured. Increasing the separation from 170 mm to 565 mm decreases the cooling power at 25 K from 220 mW to 180 mW. In most applications this would be acceptable.The pre-cooler provides cooling at a single point. In situations where refrigeration of extended objects (e.g. telescope mirrors) is required, some distribution method has to be found. A scheme for achieving this is presented together with preliminary calculations on such a system.Temperatures in the region of 2.5 to 4K are required to meet the requirements for long wavelength detectors. We have demonstrated how these temperatures can be achieved in a continuously operating closed cycle cooler that has been engineered for space applications. This cooler consists of a two-stage Stirling cycle precooling a closed cycle Joule-Thomson (JT) stage. Temperatures in the region of 4K are achieved by the use of helium-4 in the JT system. The lighter isotope of helium is used to obtain temperatures down to 2.5 K. Under no-load conditions the precooler reaches a base temperature of 11.3K. The JT system achieves 4.3 K with a 10 mW heat load and 2.5 K with a heat load of over 3 mW. The input power to the cooler is approximately 126 W.The temperature stability of the cooler at low temperatures is important to keep detector drift to a minimum. The temperature of the JT stage has been measured in uncontrolled laboratory conditions and found to vary by only 30 mK over a seventy hour period. The pre-cooler temperature varied by approximately 0.6 K during these measurements.     

Brazing diamond grits onto AA7075 aluminium alloy substrate with Ag–Cu–Ti filler alloy by laser heating

The brazing of diamond is a promising way to fabricate grinding wheels for efficient machining and precision grinding. This work investigated the feasibility of bonding diamond grits onto Aluminium Alloy 7075 (AA7075) substrate with a Ag–Cu–Ti filler alloy via laser fusion brazing. The interfacial microstructures and the strength of the brazed diamond joints were studied. The cross-section of the brazed diamond joint consists of a molten filler alloy layer, a molten pool, a heat effect zone, a columnar crystal zone and an equiaxed crystal zone. Within the interface of the filler alloy/substrate metal, microstructures observed possibly were Ag(s.s), Al(s.s), TixAl, Al2Cu and Mg intermetallic compounds. A layer of TiC with a thickness of about 30–50 nm was found at the bonding interface of the diamond/filler alloy. The averaged peak shear force of the brazed joints was found to be approximately 39.8 N. The abrasion grinding test indicated that the diamond/AA7075 brazed joint was adequate for grinding. However, the pulled-off of grit was found to be the primary failure of this type of brazed joint. This work broadened the brazing diamond technique and the range of applications of brazed diamond wheels for efficient grinding.     

钛合金高温钎焊接头的组织性能及影响因素评价

综述了钛及钛合金高温钎焊结构在现代工业中的应用。在分析了钛基钎料应用和发展的基础上，重点分析了钎焊接头的组织与接头性能的关系以及影响因素。指明接头组织中脆性金属间化合物相的存在形态是决定接头性能的主要因素，接头间隙和钎焊时间决定了接头的组织形态，从而影响接头的性能。钛及钛合金高温钎焊接头的拉伸性能、高温性能和疲劳性能是优越的，而接头氧化后的性能急剧下降。并展望了钛基材料连接的发展方向。     

A power and thermal management system for long endurance hypersonic vehicle

Due to the pneumatic heating and combustion effect, the scramjet engine of hypersonic vehicle faces high temperature challenge. It is necessary to comprehensively consider its thermal management and power generation together. A new Power and Thermal Management System (PTMS) combined with Supercritical Carbon Dioxide (SCO₂) closed Brayton cycle and fuel vapor turbine is proposed and discussed in this paper. The new PTMS can meet the cooling requirement of hypersonic vehicle at Mach number 6–7, and avoid the coking and scrapping in the scramjet cooling channels. Compared with the PTMS only based on fuel vapor turbine, the new PTMS utilizes the waste heat of scramjet to generate more electricity. In addition, it can reduce the use of fuel sink for cooling, and the additional weight penalty can be compensated for long endurance hypersonic flight.     

辅助摩擦电铸Ni-Mn合金的力学性能

利用一种新的电铸技术--游离粒子辅助摩擦电铸技术进行Ni-Mn合金的电铸试验.研究了工艺参数对Ni-Mn合金电铸层显微硬度和拉伸性能的影响规律.试验结果表明,游离粒子的辅助摩擦作用和电铸层中的锰元素共同影响着电铸层的力学性能.随着阴极旋转速率的提高,电铸层中锰含量不断增加,且游离粒子对电铸层的摩擦、挤压作用随之加强,电...     

钴对钛基钎料钎焊Ti3Al的影响

研究了Co的添加对Ti-Zr-Ni-Cu钎料的性能,以及对Ti3Al基合金钎焊接头的显微组织和机械性能的影响。研究结果表明:采用添加Co的钎料,具有良好的润湿性和流动性,可显著提高钎焊接头的拉伸强度。     

Brazing of C/C composite and Ti-6Al-4V with graphene strengthened AgCuTi filler: Effects of graphene on wettability,microstructure and mechanical properties

Graphene nanosheets(GNSs) strengthened AgCuTi composite filler(AgCuTi_G) was used to braze C/C composite and Ti-6Al-4V. The effects of GNSs on the wettability of AgCuTi_G filler on the C/C composite surface and the interfacial microstructure and mechanical properties of brazed joints were investigated. The results indicate that the addition of GNSs reduced the wettability of AgCuTi_G. The interfacial microstructure of brazed joints evolved with the addition of GNSs, where Ti_3Cu_4 and TiCu_4 were converted to TiCu and the thickness of the reaction layer adjacent to the base material decreased. The maximum shear strength of joints brazed at 0.3 wt% GNSs was 23.3 MPa(880℃/10 min). Further adding GNSs deteriorated the shear strength of the joints. Fracture of the joints occurred in the C/C composite substrate and the TiC layer adjacent to C/C composite.     

DZ125合金钎焊接头窄钎缝区高温循环应力应变分析方法

针对钎焊接头窄钎缝区(大约150μm)在高温环境下的循环应力应变测量困难问题,提出一种基于反推法的新思想,依据以下两类数据进行计算和分析:第一类是采用有限元软件ABAQUS的用户材料子程序(UMAT)嵌入Chaboche热黏塑性本构模型计算得到的DZ125母材合金高温循环应力应变数据;第二类是经高温循环试验得到的钎焊接头的相应数据,最后经过数据处理和MATLAB软件编程获得窄钎缝区的应力应变.研究结果表明,钎焊接头在高温环境下的变形具有明显的不均匀性和局部性,并指出较之母材合金其钎缝区相对较“软”,而且它也是整个钎焊接头的薄弱环节,应给予足够的重视.推而广之,反推法的提出为研究普通焊接接头窄焊缝的力学行为提供了一条新的途径.      

Micromanufacturing technologies of compact heat exchangers for hypersonic precooled airbreathing propulsion: A review

The Hypersonic Precooled Combined Cycle Engine (HPCCE), which introduces precooler into traditional hypersonic engine, is regarded as the most promising propulsion system for realizing a single-stage-to-orbit vehicle. The unique demands lead to the application of the compact heat exchangers, which can realize high thrust-to-weight ratio, sufficient specific impulse and high compression ratio. However, it is challenging to accurately manufacture the compact heat exchanger due to its extremely high heat dissipation capacity, remarkable compactness, superior adaptability and harsh operating condition. This review summarizes the precooling schemes of combined cycle propulsions and describes the demands and key issues in the fabrication of a compact heat exchanger for HPCCE. The investigation focuses on the application of various micromanufacturing methods of heat exchangers constructed from tubes of less than 1 mm in diameter and microchannels of less than 200 micrometers. Various micromanufacturing processes, which include microforming, micromachining, stereolithography, chemical etching, 3D printing, joining and other advanced microfabricating processes, were reviewed. In addition, the technologies are compared in terms of dimensional tolerance, material compatibility, and process applicability. Furthermore, the boundaries of the micromanufacturing constraints are specified as references for the design of compact heat exchangers. Ultimately, the technological difficulties and development trends are discussed for the fabrication of compact heat exchangers for HPCCE.     

P／M—SiC_p增强LY12的研究

 采用粉末冶金方法（Ｐ／Ｍ）完成了ＳｉＣ颗粒增强ＬＹ１２的成形工艺和不同重量百分比条件下的力学性能实验。测试表明,含ＳｉＣ＿ｐ２０％（ｗｔ）的复合材料在室温下平均抗拉强度可达５９４ＭＰａ,延伸率为６％。其抗拉强度比ＬＹ１２ＣＺ提高３０％；２００℃拉伸时σ＿ｂ＝４９３ＭＰａ；３１５℃时σ＿ｂ＝２９９ＭＰａ。用扫描电镜及光学显微镜观察了ＬＹ１２粉末和试样断口的组织形貌。     

硅烷偶联剂改性Al2 O3p/TDE-85 的力学性能

利用硅烷偶联剂对Al2O3颗粒进行表面改性,制备了Al2O3颗粒增强的TDE-85树脂基复合材料,研究了表面改性对其力学性能的影响,采用差热分析仪测定复合材料的固化反应温度,并计算了固化反应活化能。利用扫描电子显微镜分析了拉伸断口形貌。研究发现,当Al2O3用量为2wt%时,固化反应速度较快,硅烷偶联剂用量为4wt%时,冲击强度为13.2 kJ/m2;拉伸强度为65.2 MPa;弹性模量为2.66 GPa;最大伸长率为3.35%,此时对Al2O3颗粒的表面改性综合效果最好。     

Al合金与复合材料LID连接接头微观结构分析

通过SiC颗粒增强Al基复合材料与Al合金的液相界面扩散 (LID)连接试验 ,重点研究了连接接头区域的微观组织 ,并简要分析了接头中各元素的浓度分布情况。结果表明 ,LID连接Al基复合材料和Al合金形成的界面明显向Al合金一侧偏移 ,并且溶质原子在界面两侧分布存在明显的不对称现象。研究结果为异种材料的连接提供了重要的科学依据     

晶须增强金属基复合材料微结构参数优化设计

讨论了增强体体积比、长径比、基体与增强体的模量比以及增强体取向分布、基体的热处理状态对复合材料刚度模量的影响 ,建立了晶须增强金属基复合材料微结构参数与宏观力学性能间的定量关系 ,探索了晶须增强金属基复合材料微结构参数优化设计方法 ,给出了该材料微结构参数优化设计的典型算例     

用一种新型焊丝焊接TC18钛合金的接头性能与组织研究

对采用研制的焊丝和采用TC18同质焊材钨极氩弧焊焊接TC18钛合金的接头力学性能及微观组织进行了对比研究,结果表明:采用同质焊材焊接TC18钛合金只能保证接头的强度指标,而采用研制的新型焊丝焊接TC18钛合金,可以保证接头具有优良的综合力学性能.     

原位自生TiB2p/Cu基复合材料微观组织及性能

文摘利用Cu、Ti、B三种粉末,反应热压制备了原位TiB2p/Cu复合材料,采用XRD、扫描电镜和透射电镜分析了原位复合材料的显微组织。热压状态下,XRD分析表明材料体系在一定的工艺条件下能够完全生成TiB2p;SEM分析表明,TiB2颗粒在基体Cu中弥散、均匀分布;TEM分析发现TiB2颗粒呈六边形,尺寸约为几十微米。TiB2颗粒与基体结合良好,界面清洁,无污染。TiB2p/Cu复合材料的显微硬度及拉伸性能较基体Cu都有所提高。