A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

Analysis of a PWM-resonant converter

When a parallel resonant tank is excited by a bipolar current pulse train a sinusoidal voltage develops across the tank whose amplitude depends on the duty cycle of the pulse train. An isolated secondary can be derived by applying the tank voltage to an isolation transformer whose magnetizing inductance acts as the resonant inductor of the tank circuit. A dc output voltage is obtained after rectification and filtering of the sinusoidal secondary voltage and regulation is achieved by controlling the duty cycle of the pulse train. The sinusoidal nature of the voltage across the isolation transformer alleviates some of the noise problem associated with parasitic capacitances of an isolation transformer when operated with square voltage waveform. In this work the dc and small-signal analysis of the converter is given and an equivalent small-signal circuit model is derived. Experimental results which confirm the validity of the model are presented.     

电流控制型多路输出开关电源设计与实现

阐述了一种基于电流型脉宽调制控制器的多路输出反激变换器的设计。采用输出电压加权反馈和变压器绕组设计技术,实现了较高的多路输出电压的交叉调整率。实验结果表明,15V输出的调整率为1.6%,交叉调整率为4.86%。该电路实现简单,效率高,可靠性高,在实际应用中具有重要价值。     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

小束斑电子束脉冲轰击偏压电源的研制

为了获得一种性价比较高的电子束表面处理技术,采用定频调压电路,研制出一种新型偏压脉冲电源。这种电源由偏压主电路拓扑、偏压变压器和偏压整流滤波电路组成,其中偏压主电路由偏压基值发生电路和偏压脉冲发生电路组成。偏压基值发生电路控制偏压脉冲基值,偏压脉冲发生电路控制偏压脉冲频率和占空比。脉冲偏压电源的脉冲基值、脉冲频率、占空比均连续可调,相应实现脉冲束流的幅值、束流频率和占空比的调节。检测分析了脉冲偏压电源的输出电压波形,带载时的输出束流波形,并观察分析了电子束轰击后钨合金组织变化规律。结果表明所研制的脉冲偏压电源输出电压稳定、可调性好,能满足小束斑脉冲电子束轰击工艺的要求。     

Flyback Converter Output Voltage Stabilization

The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated.     

Nickel-Cadmium Batteries as Capacitive Filters for Pulsed Loads

This investigation consisted of several tests of specially fabricated nickel-cadmium batteries having circular disk-type electrodes. These batteries were evaluated as filter elements between a constant current power supply and a 5 Hz pulsed load demanding approximately twice the power supply current during the load on a portion of the cycle. Short tests lasting 104 cycles were conducted at up to a 21 C rate and an equivalent energy density of over 40 J/Ib. In addition, two batteries were subjected to 10h dischar cycles, one at a 6.5 C rate and the other at a 13 C rate. Assuming an electrode-to-battery weight ratio of 0.5, these tests represent an energy density of about 7 and 14 J/Ib, respectively. Energy density, efficiency, capacitance, average voltage, and available capacity were tracked during these tests. After 10y capacity degradation was negligible for one battery and about 20 percent for the other. Cadmium electrode failure may be the factor limiting lifetime at extremely low depth of discharge cycling. The output was examined and a simple equivalent circuit was proposed.     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

Development of a Low-Power Digital Inertial Reference Assembly

Current and projected system requirements for inertial reference assemblies emphasize high accuracy, long life, and low power. An inertial reference assembly ( IRA) which embodies the aforementioned characteristics was developed recently. Pulse rebalanced gas-bearing gyroscopes were used to attain high accuracy and long life. Temperature compensation of gyroscope parameters (in lieu of temperature control) and dual voltage spinmotor operation helped achieve low-power operation. The latter two items represent an advancement in the state of the art and form the subject of this paper. These techniques were used in the construction of a three-axis IRA with an operating power less than 50 watts. It has achieved 0.1 percent scale factor accuracy over a 60°F range.     

嵌入式电力控制系统中监控子系统的设计与实现

随着计算机软、硬件技术的发展，嵌入式系统在工业控制中的应用越来越广，嵌入式系统与监控软件的结合己成为工业控制领域发展的必然趋势。该系统是嵌入式电力控制系统中的一个监控子系统，系统基于组件开发，可以实现地、市级调度自动化系统、110kV及以下电压等级变电站自动化系统和10KV（35KV）及以下发电厂用电、楼宇自动化、工矿企业配电房等的中低压配电自动化系统功能。主要从硬件及软件技术方面论述了监控系统在电力自动化控制方面的应用．阐述嵌入式电力控制系统中监控子系统的核心设计与实现。     

AC/DC converter topologies for the Space Station

A new class of AC/DC converter topologies (Type-1 converters) is described, suitable for use in an advanced single-phase sine-wave voltage, high-frequency power distribution system, of the type that was proposed for a 20 kHz Space Station primary electrical power distribution system. The converter comprises a transformer, a resonant network, a current controller, a diode rectifier, and an output filter. The input AC voltage source is converted into a sinusoidal current source using the resonant network. The output of this current source is rectified by the diode rectifier and is controlled by the current controller. The controlled rectified current is then filtered by the output filter to obtain a constant voltage across the load. Three distinct converter topologies, Type-1A, Type-1B, and Type 1-C, are described, and their performance characteristics are presented. All three types have a close-to-unity rated power factor (greater than 0.98), low total harmonic distortion in input current (less than 5%), and high conversion efficiency (greater than 96%)     

Design of the Series Resonant Converter for Minimum Component Stress

For a given output voltage and power, the peak resonant capacitor voltage and peak inductor and switch currents of the series resonant converter depend strongly on the choice of transformer turns ratio and of tank inductance and capacitance. In this paper the particular component values which result in the smallest component stresses are determined, and a simple design strategy is developed. The procedure is illustrated for an off-line 200 W, 5 V application, and it is shown that an incorrect choice of component values can result in significantly higher component stresses than are necessary.     

ADC1210型12位A/D转换器的应用开发

 一、引言 ADC1210是美国National Semiconductor公司生产的一种低功耗、中速、低价格的12位二进制码（原码、或反码、或偏置码）逐次逼近式A/D转换器。该器件采用CMOS工艺和薄膜工艺相结合的微电子技术制成。器件中包含了R-2R梯形薄膜电阻网络、CMOS模拟开关和逐次逼近逻辑电路、以及场效应管电压比较器等有关电路。其基本技术指标为分辨     

基于自适应神经模糊推理算法的无人机电推进燃料电池供气系统性能优化

本文针对某无人机基于聚合物交换膜燃料电池和锂离子电池的混合动力电推进系统的应用,研究开发了一种基于自适应神经模糊推理系统的电源管理系统控制技术,以控制混合动力电力推进系统,同时优化燃料电池供气系统的性能。本文以所建立的某无人机混合电推进系统数学模型为研究对象,研究了燃料电池电流与燃料电池供气系统压缩机功率之间的关系,建立了燃料电池电流与最佳压缩机功率关系的参考模型。在参考模型的基础上,引入自适应控制器来优化燃料电池供气系统的性能。基于自适应神经模糊推理系统的控制器将压缩机的实际运行功率动态调整到参考模型中定义的最佳值。自适应控制器的在线学习和训练能力用来辨识燃料电池电流的非线性变化,并产生压缩机电机电压的控制信号,以优化燃料电池供气系统的性能。在Matlab 仿真环境中开发了质子交换膜燃料电池和锂离子混合动力电推进系统模型并对所设计的控制器进行了仿真分析,结果表明基于自适应神经模糊推理系统的控制器为燃料电池供气系统压缩机性能优化提供了一种新颖而全面的途径,使燃料电池供气系统获得最大净功率输出。将燃料电池系统的净功率输出与最佳压缩机功率和恒定压缩机功率进行了比较,结果表明优化的压缩机功率配置比恒定的压缩机功率配置节能2.62%。同时,燃料电池自适应神经模糊推理系统控制器优化了燃料电池供气系统的能量利用。     

UC3724／UC3725功率MOSFET驱动电路芯片组的应用

高电压、大电流N沟道MOSFET越来越广泛地应用于大功率的电力电子设备中。UNITRODE公司的UC3724／UC3725芯片组通过使用一种独特的调制技术－－通过小型的高频脉冲变压器同时传输信号和功率，实现简单高效的带有电气隔离的MOSFET驱动电路。此电路具有可工作在任意占空比下、实用性强、电路结构简单、响应速度快、输出阻抗小等特点。     

基于MPS4021的20W LED驱动电源设计

采用原边反馈方案设计出一款20W LED驱动电源,通过变压器初次级隔离省去了副边反馈电路,提高了驱动电源的安全性和可靠性,并节约了BOM成本。所设计的驱动电源实现了在全电压范围内输出电流精度达±5%、功率因数大于0.9、效率大于85%,使用寿命大于3万小时,电磁干扰符合EN55015限制要求,并且具备有过流保护和过压保护功能,对设计大功率LED驱动电源具有一定的参考价值。     

基于DSC整流器和双闭环PR逆变器的模块化中频静变电源

与传统中频电源相比,模块化中频静变电源具有选用灵活、可靠性高、冗余性好、便于系统维护等优点。中频静变电源整流器在控制母线电压稳定的同时还要实现单位功率因数控制。为此,具体分析了双电流环控制策略,给出了双电流环控制器中电压电流正负序分离原理和双dq锁相环的具体实现方法,即延时信号抵消(DSC)和双闭环准比例谐振(PR)。针对逆变器输出电压基波无差跟踪困难、谐波含量高等问题,采用双闭环多重准PR控制策略,实现中频电压的稳定输出。仿真和试验结果表明,双电流环控制器能同时实现母线电压稳定和单位功率因数控制,采用双闭环多重准PR控制策略的中频逆变器能够输出稳定的中频交流电压。     

Silicon Solar Cells at Low Temperature

Electrical characteristics of n-p silicon solar cells have been obtained experimentally over the temperature range of +28 to ?175° and for illumination intensities from 140 to 1.5 mW/cm2. Critical parameters and their distribution are presented for several hundred solar cells from various manufacturers. The effect of cell selection either to a minimum power output at 28° at 5 mW/cm2 or to a minimum open-circuit voltage at ?128° at 5.16 mW/cm2 upon the magnitude and distribution of the critical parameters is investigated. Considerable differences are noted, not just between cells, but also between lots from various manufacturers. Correlation analysis reveals no parameter which when measured at room temperature will predict the power output at low temperatures. This is due to a number of anomalies of the output characteristics at low temperature. These are a lack of the open voltage to continue to increase with decreasing temperature and a double break in the current-voltage characteristics. In addition, some cells show low shunt resistance which makes them have a poor performance at low intensities.     

High-Power Wide-Band RF Amplifiers

The theory and procedures pertinent to the design of wide-band high-power amplifiers and the classical theory of broadband voltage amplifiers is briefly reviewed; the differences between the design constraints for voltage amplifiers and for power amplifiers are pointed out. The requisite changes in analytical models of the amplifier are inferred; an analytical model appropriate to the design of high-power wide-band amplifiers is constructed. The observed characteristics of an amplifier are presented and compared with competitive devices. Differences between wide-band voltage amplifiers and wide-band power amplifiers are inferred directly from voltage and power gain; a procedure for designing efficient wide-band power amplifiers is presented; and application of this procedure is shown to be adequate for the design of VHF amplifiers providing average power output of 1 kW over a 50 percent bandwidth with overall efficiency of 33 percent and a power gain of 15 dB.     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer