Solar UV and ozone balloon measurements

Absolute solar UV spectra were obtained with a $\text{1}\text{4}$m spectrometer on a balloon flight from Palestine, Texas on September 23, 1981. This balloon reached a float altitude of 39 km at solar noon. The ozone density profiles derived from these spectra are discussed. The measurements are compared with data obtained from the same calibrated instrument flown in 1976 at solar minimum.     

双层乳胶气球的高空平漂机理及垂直轨迹模拟

双层乳胶气球克服了单层乳胶气球的缺点,可以在高空平漂以实现持续气象观测,但是其高空平漂受多因素影响比较复杂,特别是气球充气量主要依赖工程经验,施放成功率不高,亟需提供理论指导。通过试验数据证明了浮重平衡是双层乳胶气球实现高空平漂的必要条件,推导得出内、外球氢气充气量和昼夜温度变化对其运动的影响;建立了双层乳胶气球的几何模型和动力学模型,结合实地施放试验,对其升空和平漂过程轨迹进行模拟,由此探究了内、外球充气量对平漂高度的影响。研究结果表明:内球充气量是决定平漂高度的主要因素,并受昼夜温度变化影响,当内、外球规格分别为750g、500g,负载约1kg时,内球拉力每增大或减小0.04kg,最终平漂高度将对应升高或降低约5km,而外球充气量对其平漂高度无影响。      

Venus atmospheric platform options revisited

Various balloon systems intended as scientific platforms to float in the atmosphere of Venus at altitudes between about 35 and 65 km are briefly reviewed. Previous predictions of the altitude oscillations of balloons filled with helium gas and water vapor are largely confirmed through numerical simulation and analysis. The need for refined thermal modelling is emphasised. Several novel technical concepts are introduced. It is concluded that phase change balloons would be more suitable than non-condensing super pressure gas balloons when repeated altitude excursions are a mission requirement.     

Ion-conductivity measurements by a balloon-borne probe in the low latitude stratosphere

Three balloons were launched from Hyderabad, India in order to measure the electrical conductivity in the stratosphere. The measurements show that at the float altitude of around 34 km the positive ion conductivity is higher than the negative ion conductivity by a factor of 3 to 5 during daytime. In nighttime they differ by a factor of around 1.3. The conductivity values measured during one of the balloon flights (Apr. 1984) showed marked variations with time. It is suggested that these variations might have a weather related origin.     

Development of balloon-borne reel-down and -up winch system

Balloon-borne winches, which can reel down and up scientific instruments repeatedly, have been developed since 1981 in order to observe stratospheric vertical microstuctures. The instrument is suspended by a kevler wire through a traverse-cum ropeguide, and its depth is accurately measured by counting numbers of spool rotations and ropeguide turns. Battery consumption is minimized by utilizing an efficient deccelerator and a hysteresis brake. In 1983 we have successfully performed to reel up and down a 12 kg payload through 1 km for three cycles at 24 km altitude. We are improving the capability of the winch, and have succeeded (May 1984) to reel down a 22 kg payload up to 3 km from a balloon.     

Microgravity experiment system utilizing a balloon

A system for microgravity experiments by using a stratospheric balloon has been planned and developed in ISAS since 1978. A rocket-shaped chamber mounting the experiment apparatus is released from the balloon around 30 km altitude. The microgravity duration is from the release to opening of parachute, controlled by an on-board sequential timer. Test flights were performed in 1980 and in 1981. In September 1983 the first scientific experiment, observing behaviors and brain activities of fishes in the microgravity circumstance, have been successfully carried out. The chamber is specially equipped with movie cameras and subtransmitters, and its release altitude is about 32 km. The microgravity observed inside the chamber is less than 2.9 × 10^?3 G during 10 sec. Engineering aspects of the system used in the 1983 experiment are presented.     

Detection of solar neutrons on a long duration balloon flight

The observation of large solar flares on high altitude balloons requires long duration balloon flights because large flares are infrequent and cannot be predicted with enough reliability and lead time to allow a conventional balloon to be launched and reach altitude before the flare occurs. With the many weeks at float altitude expected for a long duration flight, the probability of “catching” a large flare during solar maximum becomes reasonably high and the study of phenomena which heretofore have required a satellite become accessible to a balloon platform. One example of this type of experiment is the observation of neutrons produced by the interaction of flare accelerated nucleons with the solar atmosphere. Because the neutrons are produced immediately by the flare accelerated particles and are unaffected by their transmission through the upper solar atmosphere and the intervening magnetic fields, their observation at 1 A.U. will provide direct information on the flare acceleration process. Specifically, a measurement of the neutron energy and time spectra will yield the energy spectrum of the charged nucleons in the interval 50 to 500 MeV/amu, the charged particle anisotropy, the height of the acceleration region for limb flares, and information on the two-stage acceleration process. Because the γ-ray spectrum is also sensitive to these factors, a combined neutron and γ-ray measurement will provide a much more stringent test of flare models than either done separately. CWRU and the University of Melbourne have designed the EOSCOR (Extended Observation of Solar and Cosmic Radiation) detector to have the necessary sensitivity to detect neutrons from a flare 0.1 the size of the 4 Aug. 1972 event and to be compatible with the constraints of the long duration balloon system. The detector has been test flown on short duration balloon flights and calibrated at E_n = 38, 58, and 118 MeV. It is planned to launch it on a long duration balloon flight from Australia in December 1982 when simultaneous γ-ray observations will be possible with the SMM and/or HINTORI satellites.     

Feasibility study of a sea-anchored stratospheric balloon for long-duration flights

Sea-anchored balloons are stratospheric super-pressure balloons that are anchored to the sea. The sea-anchored balloon is a simple system that has the capability for long-duration flights, fixed-point observations, flexible launch windows, easy telemetry links to ground stations, and quick recoveries. Such balloons are not required to fly through the jet stream while tethered to the ground or sea, because the tether is deployed from a reel on the balloon after reaching a floating altitude. In this study, the feasibility of the sea-anchored balloon is investigated, with particular emphasis on the tether strength, balloon altitude, and system mass, based on the present technological level of the tether’s specific strength. Although the wind distribution with altitude is a dominant factor for feasibility, a sea-anchored balloon with an altitude of about 25 km would be feasible if the velocity of the jet stream is sufficiently low. The sea-anchored balloon can be simply flight-tested, since additional ground facilities and special flight operations are not necessary.     

Technology development for a long duration,mid-cloud level Venus balloon

This paper describes the results of ongoing technology development activities for a Venus spherical superpressure balloon capable of flying for long durations (30 days) in the middle cloud layer at an altitude of 55.5 km. Data is presented from a successful aerial deployment and inflation flight experiment on a 5.5 m diameter prototype balloon conducted at a 2.5 km altitude above the Earth. Although the balloon in that test was not released for free flight, all other steps in the deployment and inflation process were successfully executed. Experimental and computational results are also presented from an investigation of the stress concentration phenomenon at the junction of the metal end fitting and fabric end cap of the prototype Venus balloon. Good agreement was found between the simulation and experimental results and a stress concentration factor of 1.55 determined for this end cap design compared to the expectations of thin membrane theory. Finally, results are presented for a new, second-generation Venus balloon material utilizing Aclar™ film instead of Teflon. Optical property and sulfuric acid tolerance data are presented for this material based on laboratory testing of samples.     

A neutral gas mass spectrometer to measure the chemical composition of the stratosphere

The Polar Balloon Atmospheric Composition Experiment (P-BACE) is a new generation of neutral gas mass spectrometer based on the time-of-flight principle. P-BACE is the scientific experiment on the Mars Environment Analog Platform (MEAP) flown successfully on a balloon mission in summer 2008. The MEAP mission was flown with a 334,000 m³ helium balloon in the stratosphere on a semicircular trajectory from northern Sweden around the North Pole to Canada using the summer northern hemispheric wind current. The atmospheric conditions at an atmospheric altitude of 35–40 km are remarkably similar to those on the surface of Mars and thus the balloon mission was an ideal testbed for our mass spectrometer P-BACE. Originally this instrument was designed for in situ measurements of the chemical composition of the Martian atmosphere.P-BACE has a unique mass range from 0 to 1000 amu/q with a mass resolution m/Δm (FWHM) > 1000, and the dynamic range is at least six orders of magnitude. During this experiment, the acquisition of one mass spectrum is a sum of 65,535 single spectra, recorded in a time frame of 66 s.The balloon mission lasted 5 days and had successfully demonstrated the functionality of the P-BACE instrument during flight conditions. We had recorded more than 4500 mass spectra. With little modifications, P-BACE can be used on a planetary mission for Mars, but for example also for Venus or Mercury, if placed on a satellite.     

A new reeling technique for very long extension scanning in the stratosphere

A balloon borne winching system has been developed for extending a very long tether with payload down into the stratosphere and recovering it; this has been flight proven by being carried to an altitude of 40 km, lowering a 62 kg stratospheric photochemistry experiment 12 km at a descent velocity of ～6–8 m/sec and recovering it at comparable velocities. During the first flight, data gave no evidence of dynamic instabilities due to the system or the stratospheric interactions. The future utility of this payload is discussed with attention to the design factors that bound the range of performance of this type of system.     

The measurement of water vapour in thermal emission on studies of nimbus-7 stratoprobe flights for correlative studies of nimbus-7

A scanning infrared radiometer used to measure nitric acid was flown on the STRATOPROBE Flight of November 8, 1978. Using the observed thermal emission from 6.5 to 7.4 microns during the balloon ascent, a water vapour profile has been derived using a band model of the water vapour lines in this spectral region. The resulting profile has a minimum of 3.3 ppmv at the tropopause and then rises to a value of 5 ppmv by 30 km. The profile is comparable to the profile from another water vapour instrument from the National Physical Laboratory which was flown on the LIP balloon payload on the same day. A coincident profile from the LIMS experiment on NIMBUS 7 was also obtained since the STRATOPROBE experiment was flown as a correlative measurement for the LIMS experiment.     

Scientific ballooning in Japan – An over view of recent activities

Current status of scientific ballooning in Japan is reviewed. First, I describe successful application of balloon technologies to construct a vessel of transparent plastic film, to contain about 1000 tons of liquid scintillator in Kamioka Liquid Scintillator Anti-Neutrino Detector (KamLAND). KamLAND is a project to study neutrino oscillation phenomena, by detecting anti-neutrinos produced in distant nuclear reactors. Next, I describe high altitude balloons developed by the ISAS balloon group. They developed balloons made from ultra-thin polyethylene film, producing a balloon of volume 60,000 m³ which successfully reached an altitude of 53 km in 2002. This is a world record, the greatest altitude that a balloon has ever achieved. ISAS is applying further effort to develop balloons with even thinner films, to achieve a higher altitude than 53 km. Other recent activities by the ISAS balloon group are briefly described.I also review scientific ballooning projects now operating in Japan, particularly focusing on the Balloon-Borne Experiment with a Superconducting Spectrometer (BESS) program. This is a US–Japan collaborative program that has carried out very precise measurements of antiprotons, protons and other components in primary cosmic rays, as well as measuring the fluxes of atmospheric muons and other components. The results of these observations give us important information to improve our understanding of the production mechanism of antiprotons observed in the primary cosmic rays. The data are also important for analysis of atmospheric neutrino events observed by Super-Kamiokande and other ground-based neutrino detectors. Future prospects of BESS and other balloon-borne cosmic-ray research programs are also presented.     

Long extension reeling in the stratosphere — A progress report

A balloon-borne winching system providing an improved in-situ observational method for stratospheric photochemistry research was first reported to COSPAR two years ago. Sice that time a second flight has been successfully conducted in which a more complex detection package (98 kg) was twice lowered from a float altitude of 39 km for a distance of 8 km, and each time reeled back up to the winch. Controlled velocities of 4 to 7 meters/sec were implemented for both scans, and the package was brought to a brief stop during the first to evaluate the dynamic effects. Instrumentation aboard both the winch and the detection package again did not identify any threatening dynamic perturbations during any phase of the flight, thus indicating that long extension reeling in the stratosphere can now be conducted on an operational basis. The remaining minor problem areas in the payload are summarized, as are some directions planned for future utilization.     

利用HRDI/UARS资料分析东亚区域中层大气纬向风气候特征

利用美国高层大气研究卫星(UARS)搭载的高分辨率多普勒测风仪(HRDI)获得的中层大气风场观测资料,对东亚区域中层大气纬向风的垂直分布与变化特征进行了分析研究.多年平均结果显示东亚区域中层大气纬向风具有显著的区域特征,与当前普遍使用的参考大气CIRA-86相比存在显著的不同.在冬季,东亚区域中间层西风急流中心位于25°-35°N之间的75 km高度,与CIRA-86相比,该中心纬度偏南5°,高度偏高10 km;在秋季,东亚区域低热层高度存在一个显著的从赤道到高纬度的东风带,而CIRA-86不存在.分析结果还表明,除了夏季中纬度地区,在东亚区域上空中高层大气各高度上均存在相当显著的区域尺度扰动结构.在热带,低热层高度纬向风无论冬夏,沿纬圈方向都表现出相当显著的不均匀性,夏季这种不均匀性进一步向下扩展到55 km高度.与上述热带扰动特征相比,中纬度地区夏季的纬向风在各个高度沿纬圈相当均匀,但是在冬季,中间层和低热层高度都存在沿纬圈方向显著的纬向风扰动结构.      

Second generation prototype design and testing for a high altitude Venus balloon

This paper describes the development of a second generation prototype balloon intended for flight in the upper atmosphere of Venus. The design of this new prototype incorporates lessons learned from the construction and testing of the first generation prototype, including finite element analyses of the balloon stresses and deformations, measured leak performance after handling and packaging, permeability and optical property measurements on material samples, and sulfuric acid testing. An improved design for the second generation prototype was formulated based on these results, although the spherical shape and 5.5 m diameter size were retained. The resulting balloon has a volume of 87 m³ and is capable of carrying a 45 kg payload at a 55 km altitude at Venus. The design and fabrication of the new prototype is described, along with test data for inflation and leakage performance.     

The VEGA Venus balloon experiment

In June 1985, two instrumented balloons were placed in the atmosphere of Venus as part of the VEGA mission. Each balloon traveled about 30 percent of the way around the planet at a float altitude near 54 kilometers. In situsensors measured pressure, temperature, vertical wind velocity, cloud particle backscatter, ambient light level, and frequency of lightning. A ground-based network of 20 radio antennas tracked the balloons by very long baseline interferometry (VLBI) techniques to monitor the Venus winds. The history, organization, and principal characteristics of this international balloon experiment are described.     

Study of seasonal variation of winds in upper stratosphere over Hyderabad

A predictability of the stratospheric zonal winds above 38 km during the turnaround is an essential parameter for planning of the high-altitude scientific balloon flights. This information is more relevant in the case of Hyderabad balloon facility which is closer to equator and has much more unstable wind reversal patterns which appears to have changed enormously during the last decade probably in correlation with the global warming. With a majority of our flights reaching the altitudes of 38–42 km and the requirement of long float durations, a prior knowledge of wind pattern during the summer and winter turnaround seasons is highly desirable. Furthermore, the flight operation corridor for balloon flights from Hyderabad is limited to 400 km and though in the west direction there are flat lands, in all other three directions, the landscape is dotted by water bodies, reserve forests and hilly terrain, and therefore need of such a data is essential. In order to establish the climatology of the stratospheric winds and study their inter-annual variability over Hyderabad for the turnaround periods, we have made a detailed analysis of the United Kingdom Meteorological office data between 2000 and 2007, to derive average wind parameters (magnitude, direction) at different ceiling altitudes above 38 km. These results can be used only as general trend of stratospheric wind and should not be the limitation of the UKMO Data.     

The high altitude student platform (HASP) for student-built payloads

An outstanding issue with aerospace workforce development is what should be done at the university level to attract and prepare undergraduates for an aerospace career. One approach adopted by many institutions is to lead students through the design and development of small payloads (less than about 500 grams) that can be carried up to high altitude (around 30 km) by a latex sounding balloon. This approach has been very successful in helping students to integrate their content knowledge with practical skills and to understand the end-to-end process of aerospace project development. Sounding balloons, however, are usually constrained in flight duration (∼30 min above 24 km) and payload weight, limiting the kinds investigations that are possible. Student built picosatellites, such as CubeSats, can be placed in low Earth orbit removing the flight duration constraint, but the delays between satellite development and launch can be years. Here, we present the inexpensive high altitude student platform (HASP) that is designed to carry at least eight student payloads at a time to an altitude of about 36 km with flight durations of 15–20 h using a small zero-pressure polyethylene film balloon. This platform provides a flight capability greater than sounding balloons and can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. The HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. HASP is lightweight, has simple mission requirements providing flexibility in the launch schedule, will provide a flight test opportunity at the end of each academic year.