应用于航空变频电源系统的新型串沥混合有源滤波器

 目前变频交流(AC)电源系统开始逐渐应用到新型多电飞机(MEA)中,传统有源滤波器无法满足宽输入频率变化要求,为此需要设计一种适合于宽变频航空电源系统的有源滤波器。本文研究了一种应用于航空变频电源系统的新型串联混合有源滤波器(SHAPF),该有源滤波器直接根据基波电流进行补偿,针对各种频率输入均能起到较好的抑制谐波作用。讨论了这种新型SHAPF的变频谐波抑制原理,给出了该滤波器的控制系统详细设计过程,包括基于双数字信号处理器（DSP）的控制平台设计和逐点动态检测基波电流的算法设计,最后进行了样机实验,对比了加入滤波器前后系统输入电流实验波形和谐波分析,加入滤波器后系统输入电流总谐波失真度（THD）由174.00%变化至4.80%,滤波效果良好;在360 Hz,400 Hz和720 Hz不同输入频率进行了滤波实验,验证系统在宽变频输入条件下均具有良好控制性能,满足航空变频输入时输入功率因数校正要求。     

False Alarm Rate for Rank Quantizer When Input Range Samples are not Independent

Under the assumption that the non-independent range samples fed into the rank quantizer form a first-order Markov sequence, the first threshold false alarm probability Pn is written in the form of a multiple integral, the multiplicity being equal to the number of samples or quantizer taps. The Rice model for narrow-band noise (clutter) is used to check the effect of correlation on Pn using the derived formula. For the limited case examined, correlation be tween samples decreases Pn as compared with the independent samples case.     

Aircraft Power System Harmonics Involving Single-Phase PFC Converters

AC-DC converters with active power factor correction (PFC) are replacing uncontrolled diode rectification circuits on commercial jet airplanes in order to meet harmonic distortion limits imposed by new airborne electrical system power quality standards. The high line frequency of airborne AC power systems presents a major challenge for the design of PFC converters capable of meeting these standards. This paper investigates a new source of harmonic current distortion and the resulting system power quality problems related to dynamic interactions between PFC converters and the AC source. Experimental results are first presented to demonstrate the existence of such interactions and their effects on system power quality. Analytical and numerical simulation results are then presented to explain why such dynamic interactions can lead to significantly increased harmonic current distortion in steady state operation. Elimination of undesirable system interactions through proper damping of the PFC converter input filter is also presented and its effectiveness experimentally validated.     

热轧AZ31镁合金温变形中的微观组织演变

在50~250℃的温度范围和1.4×10^-3~1.4×10^-1s^-1的应变速率范围内通过单向拉伸试验检验了热轧AZ31镁合金的温变形性能。通过光学显微镜和透射电镜观察了温变形中的微观组织演变。结果表明:在温变形的初始阶段,孪生为主要的变形机理和硬化机制。由孪生变形积聚的畸变能和非基滑移的启动导致了动态再结晶的形核与长大。应变速率的提高对动态再结晶的抑制是造成AZ31镁合金温变形中应变速率敏感性的原因。     

大多普勒容限巴克码脉压

 本文介绍用补偿式非相干型旁瓣抑制滤波器(SSF)实现13位巴克码脉冲压缩旁瓣抑制的理论计算及实验结果。补偿式非相干型SSF采用最小二乘近似逆滤波方法设计,若子脉冲宽度为0.7μs,峰值旁瓣电平不超过-30dB,这种SSF的多普勒容限能达到-40kHz～+40kHz。理论计算及实验结果都表明,所设计的补偿式非相干型SSF的多普勒容限比具有同样长度冲激响应序列的R-G-ISSF有显著改善。     

基于级联型SOGI的永磁同步电机谐波电流抑制方法研究

伺服驱动器由于具有很强的非线性,导致永磁同步电机(PMSM)的定子电流中含有大量的高次谐波并且引发较大的转矩脉动。针对这一问题,提出基于级联型二阶广义积分器(SOGI)的谐波抑制方法,将级联型SOGI与电流环d、q轴的PI控制器并联,利用级联型SOGI提取d、q轴电流中的6次谐波分量,并将其注入到PI控制器的输出电压中,从而抵消参考电压中的谐波。仿真结果表明:采用基于级联型SOGI的电压补偿法进行谐波抑制,电流波形的畸变得到了明显改善,证明了所提算法的有效性。     

Adaptive cancellation method for geometry-induced nonstationary bistatic clutter environments

This paper describes and characterizes a new bistatic space-time adaptive processing (STAP) clutter mitigation method. The approach involves estimating and compensating aspects of the spatially varying bistatic clutter response in both angle and Doppler prior to adaptive clutter suppression. An important feature of the proposed method is its ability to extract requisite implementation information from the data itself, rather than rely on ancillary - and possibly erroneous or missing - system measurements. We justify the essence of the proposed method by showing its ability to align the dominant clutter subspaces of each range realization relative to a suitably chosen reference point as a means of homogenizing the space-time data set. Moreover, we numerically characterize performance using synthetic bistatic clutter data. For the examples considered herein, the proposed bistatic STAP method leads to maximum performance improvements between 17.25 dB and 20.75 dB relative to traditional STAP application, with average improvements of 6 dB to 10 dB.     

行波管放大器非线性特性对调幅信号边带压缩影响

为了更精确地测试星上功率放大器的饱和点,研究分析了TWTA(Travelling-Wave Tube Amplifier,行波管放大器)的非线性特性对AM(Amplitude Modulation,调幅)信号的边带压缩影响。文中基于Saleh模型描述TWTA,分析其在AM信号放大过程中的非线性特性,研究表明:随着输入AM信号的功率不断增大,放大后的输出信号畸变越来越严重;该变化主要体现在AM信号的边带上,与线性工作区相比,在TWTA的饱和点处,经放大后的AM信号的边带压缩程度达到最大。实验结果与理论分析结果完全一致。该研究为通信卫星星上功放饱和点测试提供了一种可行方法。     

Distortion Generated in Angle-Modulation Systems by Phased Arrays

The case of linear, uniformly weighted phased arrays is examined via time and frequency domain analyses. Bounds that must be placed on array length, modulation frequency, modulation index ?, and scan angle relationships if excessive distortion is to be avoided in wideband angle-modulated communication systems are established. Distortion is shown to consist of odd harmonic terms. It is also shown that, for one class of equivalent RF signals, phased arrays produce approximately three times as much distortion in frequency-modulation (FM) systems as in phase-modulation (PM) systems. Graphs of distortion plotted as functions of signal and array parameters show that, for practical array sizes, distortion is a monotonically increasing function of the product of L and sin ? where L is the length of the array expressed in modulation wavelengths ?m and ? is the scan angle. In PM systems, distortion also increases monotonically with the modulation index ?. Plots of distortion versus L sin ? show that even relatively small arrays can produce intolerable distortion levels in wideband systems; e.g., an FM system having ? = 3,L = 0.35?m, and ? = 60 degrees exhibits approximately 20 percent distortion.     

暂冲式风洞大开角扩散段性能的实验研究

布置有多层孔板（丝网）的大开角扩散段通过参数的优化设计,可有效缩短暂冲式风洞启动时间,均匀进入稳定段的气流速度,并降低阀后噪声和气流脉动。针对某大型暂冲式风洞大开角扩散段设计关键技术开展专题研究,设计并进行了不同扩散段扩开角角度和中心体分流锥型式的组合实验,从压力损失、出口截面速度分布和降噪特性三个方面进行了对比分析。试验结果表明：试验件45°扩开角＋65°平底锥的压力损失相对最小,而增加导流尾锥的中心分流锥由于底部难以形成稳态的分离涡使得其压力损失明显偏大,其它试验件组合的压力损失值则相接近;各试验件出口截面的速压分布均呈现以中轴线对称分布的双驼峰趋势,且孔板的开孔率偏高时出口剖面速度分布相对更平滑;试验马赫数下的大开角段对气流噪声的消声量约为12～14dB,对频率在2kHz以上的气流噪声具有相对较强的消声能力,同时气流经过设置有多层孔板的大开角扩散段后,气流波动幅值明显降低,气流脉动得到有效地抑制。     

高阶谐波控制对旋翼桨-涡干扰载荷和噪声的影响

直升机小速度平飞和斜下降飞行时会产生严重的桨-涡干扰(BVI)噪声。基于修正Beddoes尾迹/桨叶动力学耦合方法和Farassat 1A公式,建立了一个新的能够计入高阶谐波控制(HHC)影响的旋翼桨-涡干扰气动载荷和噪声计算模型。在该模型中,高阶谐波控制引起的桨尖涡附加位移通过对高阶入流进行时间积分推导得出,而单一阶次的谐波输入引起的各阶谐波响应通过传递函数来确定,传递函数则由桨叶的动力学特性计算。首先对HARTⅡ旋翼斜下降飞行状态的桨-涡干扰气动载荷进行了计算模拟,验证了所建立方法的可靠性。然后,着重研究了在典型的三阶谐波桨根激励下,不同输入相位对HARTⅡ旋翼桨-涡干扰气动载荷和噪声特性的影响。结果表明:桨叶的动力学特性尤其是扭转特性对高阶谐波控制效果影响显著,且高阶谐波输入的相位选择对桨-涡干扰噪声的控制至关重要,若控制相位选择不当,反而会增大旋翼噪声。     

Effects of Modulation Nonlinearity on the Range Response of FM Radars

The effect of modulation nonlinearity on the range response of FM radars with harmonic processing and ?triangle? modulation is derived. The nonlinearity may be desirable or undesirable; that is, the sidelobe level of the range response may be decreased or increased depending on the shape and amount of nonlinearity. The results of this paper may be used to predict the actual range laws of existing ?linear? FM radars; or, alternately, to specify the desired amount of modulation nonlinearity for new FM radars so that superior sidelobe suppression can be realized.     

谐波陷波法超低频标准振动台失真度控制

波形失真度是影响超低频振动计量校准精度的重要因素。本文提出了利用谐波陷波法反馈方式进行失真度控制的一种方案,分析了控制过程,并给出了反馈算法。实验表明,该方法能快速降低振动台的失真度,将失真度控制在2%以内。     

单脉冲双极化天线阵列设计

文章研究了单脉冲双极化天线阵列。天线阵混合馈电微带单元由共面微带线馈电和缝隙耦合微带线馈电两者结合形成,"十"字形微带单脉冲比较器与天线阵同面,具有结构紧凑、加工方便和成本低的优点。经仿真验证,在工作频带内其辐射单元双端口隔离度高于34dB;并且2个极化端口在其对应主平面方向的副瓣电平均低于-20dB。天线可适用于新一代多极化雷达系统。     

跨声风扇周向畸变流动的谐波平衡法计算

研究了采用"相位延迟"边界条件的谐波平衡法用于周向进气畸变计算的可行性及其计算效率,考虑了进气总压畸变形式为正弦波和方波的两种情况。对于正弦波形式的进气总压畸变采用较少阶数的谐波计算就可得到和双时间推进法相近的计算结果,计算速度最大可以提高48倍。对于方波形式的进气畸变,则需要采用更多阶数的谐波计算才能还原得到较准确的非定常流场,计算速度提高了7倍。算例表明,谐波平衡法可以有效的应用于跨声风扇周向进气畸变的非定常计算中,同时大幅提高计算速度。     

S弯喷管喷流噪声特性研究

为了研究S弯喷管亚声速喷流的噪声特性,采用大涡模拟结合FW-H方程方法,通过数值模拟得到轴对称喷管和S弯喷管的流场及远场噪声。结果表明：S弯喷管的S形弯曲及圆转方构型导致了主流流向变化和横向压力梯度,S弯喷管出口截面角区及下方中心线附近均有不同尺度的旋涡分布,通过加强掺混减弱喷流与大气之间的剪切,使得S弯喷管噪声源尺度小于轴对称喷管。S弯喷管将St=0.08~0.2的噪声转移到St=0.2~0.3,在喷流下游10°~50°,S弯喷管相比于轴对称喷管噪声总声压级减小了6~8dB,在20°接收点处降噪效果最佳,相比于轴对称喷管减小了约8dB。在喷流上游S弯喷管降噪效果减弱,仅减小了2~4dB。在下游10°~80°处,S弯喷管水平探测面噪声总声压级比垂直探测面高2~3dB,在喷流上游二者差异较小。     

High Dynamic GPS Receiver Using Maximum Likelihood Estimationand Frequency Tracking

A new high dynamic global positioning system (GPS) receiver ispresented and its performance characterized by analysis,simulation, and demonstration. The demonstration receiver is abreadboard model capable of tracking a single simulated satellitesignal in pseudorange and range rate. Pseudorange and range rateestimates are made once every 20 ms, using a maximum likelihoodestimator, and are tracked by means of a third-order fadingmemory filter in a feedback configuration. The receiver trackspseudorange with rms errors of under 1 m when subjected tosimulated 50 g, 40 g/s circular trajectories. The tracking thresholdis approximately 28 dB·Hz, which provides 12 dB margin relativethe the minimum specified signal strength, assuming 3.5 dB systemnoise figure and 0 dB antenna gain.     

冠状喷口抑制涡扇发动机喷流噪声试验和数值研究

 以揭示发动机喷流噪声声场分布和冠状喷口抑制喷流噪声为目的,对涡扇发动机排气噪声声场和喷流流场进行了试验和数值计算,对比分析不同结构的冠状锯齿对喷流噪声的综合抑制效果。结果表明:采用大涡模拟(LES)、FW-H (Ffowcs Williams-Hawkings)声学模型和傅里叶变换的方法,可以预测出喷流噪声的空间分布和声压级值;冠状锯齿产生的阵列流向涡是强化流体间混合、降低喷流速度峰值、抑制喷流噪声的根本所在;在本文研究参数范围内,冠状锯齿结构不仅将排气喷流噪声由原型排气系统的159.6 dB降低到154.3 dB,而且冠状锯齿给喷管带来的损失控制在1.7%以内。锯齿冠状结构对分开排气式大涵道比涡扇排气系统喷流噪声有抑制作用。     

对进气道插板试验数据的一点探讨

以实际进气道 /发动机插板逼喘试验数据为依据 ,对发动机进口畸变流场的试验数据进行了分析 ,并对进一步改进动态数据采集的设计提出了一点看法 ,供探讨。     

Clutter Residues of a Coherent MTI Radar Receiver

In moving target indicator radar receivers a saturation is always present in the IF stages in order to compress the dynamic range of large clutter inputs. This nonlinearity greatly affects the performances of the cancelling circuits, because of the spreading of the spectra. A quantitative analysis of this effect has been conducted, with an analytical expression chosen for the limitation characteristic. A high degradation of both single-and double-canceller improvement factors has been obtained. Losses of 20 dB for the double canceller are not uncommon. Clutter residue levels at the receiver output have also been computed in order to see how the performance compares with ideal constant false alarm rate behavior.