某任务计算机调试设备配套软件的设计与实现

简介了任务计算机调试设备配套软件在任务计算机仿真环境中的重要作用 ,对该软件设计方法和流程进行了详细的说明 ,主要介绍了VC ++6 .0环境下串行通信和显示控制软件的设计技术 ,并讨论了如何提高应用程序性能的途径。     

从科技论文的特点看科技论文的选题

本文论述了科技文的特点及选师原则。在特点方面主要就科技论文的科学性,创造性,理论性进行了阐述,在选题方面科技论文选题的客观需要与主条件进行阐述,旨在揭示科技论文的特点与课题选择之间的关系,从而了解其特点,并据此选题,写出符合要求的科技论文。     

Impact of a cavitation bubble on a wall

Impulse action of a cavitation bubble on a rigid wall is studied depending on the distance between them. We determine the distances at which the periphery pressure maximums on a wall are preserved as well as the distances at which these maximums exceed the water hammer pressure.     

Analysis of a redshifted plasma flow over a sunspot

The ultraviolet spectrum of a redshifted plasma flow appearing over a sunspot observed during the first flight of the High Resolution Telescope Spectrograph (HRTS I) is analysed, and interpreted as a radiatively cooling plasma. For most of the lines emitted from this plasma, the assumption of ionization equilibrium during the cooling is good. However for He II (and other ions with a single electron outside of closed shells), this is not the case. Integrating differential equations for the various ionization fractions of helium and the temperature allows an approximate determination of the abundance of helium relative to other elements whose lines appear in the spectrum of the plasma flow.     

The intersection of a Loxodrome with a great circle

The intersections of a loxodrome (rhumb line) and a great circle are of interest for some navigational problems, but a closed-form solution cannot be formulated. An algorithm is given for computing approximations to any desired degree of accuracy using Newton's method. By using the equatorial angle φ as an independent variable all solutions can be found rapidly using the modest computational capabilities of a personal computer     

Effect of a transverse plasma jet on a shock wave induced by a ramp

We conducted experiments in a wind tunnel with Mach number 2 to explore the evolution of a transverse plasma jet and its modification effect on a shock wave induced by a ramp with an angle of 24°. The transverse plasma jet was created by arc discharge in a small cylindrical cavity with a 2 mm diameter orifice. Three group tests with different actuator arrangements in the spanwise or streamwise direction upstream from the ramp were respectively studied to compare their disturbances to the shock wave. As shown by a time-resolved schlieren system, an unsteady motion of the shock wave by actuation was found: the shock wave was significantly modified by the plasma jet with an upstream motion and a reduced angle. Compared to spanwise actuation, a more intensive impact was obtained with two or three streamwise actuators working together. From shock wave structures, the control effect of the plasma jet on the shock motion based on a thermal effect, a potential cause of shock modification, was discussed. Furthermore, we performed a numerical simulation by using the Improved Delayed Detached Eddy Simulation(IDDES) method to simulate the evolution of the transverse plasma jet plume produced by two streamwise actuators. The results show that flow structures are similar to those identified in schlieren images. Two streamwise vortices were recognized, which indicates that the higher jet plume is the result of the overlap of two streamwise jets.     

Oscillations of a viscous liquid in a cylindrical container

The natural damped frequencies of a viscous liquid in a circular cylindrical container are obtained for slipping and anchored contact line at the container wall r = a. In addition the response to translational forced excitation has been determined. The results may also be applied to viscous liquid in a micro-gravity environment, as long as the contact angle of the liquid surface to the cylindrical container wall is in the vicinity of π/2, indicating, that the free liquid surface equilibrium position remains a plane surface. It could be found that there exists in contrast to frictionless liquid a small filling range, in which the liquid performs only an aperiodic motion. The adherence condition at the side wall was replaced by the somewhat weaker condition of an anchored contact line.     

Relativistic Energy-Momentum of a Body with a Finite Volume

The problem of energy-momentum in a body with a finite volume has been causing confusion in the theory of relativity, especially in relativistic thermodynamics. Its correct understanding has been given since the early years of relativity, however, erroneous misunderstandings are still found in papers and textbooks to this date. The present paper introduces a simple paradox to demonstrate the problem, and gives a brief review on a way to handle the energy-momentum correctly.     

某型弹用发动机火药吹转模拟试验

针对某型弹用发动机火药起动试验件起动试验要求,通过静态烟火试验数据确定火药起动模拟试验设备技术指标,在试验台上进行了高压冷吹和真实火药热吹起动试验,获取了两类试验下模拟转子的起动特性.试验结果表明:通过静态烟火试验和高压冷吹测得不同压力下空气流量、转速数据可以拟合出相关关系式,通过关系式能够预估燃气发生器所用火药量在热吹试验中转子可能最大转速,最后通过0.8kg真实火药热吹试验获取的最高转速与换算压力状态下的冷吹最高转速仅相差116r/min,进一步验证了试验和预估方法的有效性和准确性,可以减少或取消不同装药量火药在模拟转子上的吹转试验,减低在发动机上的试验安全风险,为在发动机上的应用奠定基础.      

Excitation control of a synchronous generator using a lookup table

A scheme involving the use of a lookup table is developed for the excitation control of a synchronous generator. The proposed control scheme, generator speed deviation, and acceleration deviation are taken as the input signals. These input signals are sampled and converted to linguistic terms before they are fed into the controller. The controller generates the desired output (control) signal by using a set of production rules (if-then rules) that are based on previous experience to relate the input signals to the output. The output signal is converted from linguistic terms to a numerical value before it is sent to the excitation system of the synchronous machine. To demonstrate the effectiveness of the proposed control scheme, digital simulations of a synchronous generator subject to a three-phase fault under different operating conditions were performed. It was found that the controller can improve the dynamic performance of a synchronous generator over a wide range of operating conditions. Since the controller does not require model identification, it is computationally efficient and is suitable for online excitation control, using a microcomputer     

Three-dimensional model of a dispersed-film flow in a cylindrical channel

A mathematical model of the dispersed-film two-phase flow with phase slip in the vertical cylindrical channel is described.     

带套齿联轴器的转子系统动力学特性研究

针对大涵道比涡扇发动机低压转子中套齿式刚性联轴器结构,建立了套齿联轴器的力学模型和通过套齿联轴器连接的试验转子系统,通过动力学特性计算选择合适的支承刚度,以满足一阶、二阶临界转速的设计要求。理论分析和试验研究了轴向螺母拧紧力矩对套齿连接刚度以及对转子系统的临界转速、振型和不平衡响应等动力学特性的影响规律。结果表明:轴向螺母拧紧力矩会增大套齿联轴器的连接刚度,并且呈现明显的非线性特征。随着轴向螺母拧紧力矩从60N?m增大到120N?m,转子系统的一阶与二阶临界转速增长率分别为1.23%与0.51%;对应的不平衡响应幅值不同程度地增大;而对应的振型基本保持不变。改变不平衡量的轴向与周向位置会导致不平衡响应幅值大小及其变化率有所不同。     

Angular Accuracy of a Scanning Radar Employing a Two-Pole Filter

A two-pole filter is proposed as a detector for a scanning radar. The optimum values of the filter coefficients are found and are approximated by a simple expression. The optimum two-pole filter requires a 0.15-dB increase in signal-to-noise ratio in order to provide the same detection capability as the optimum detector, and yields azimuth estimates whose standard deviation are within 15 percent of the Cramér-Rao lower bound. The estimator is simple to implement, avoiding the storage requirements of the moving window detector and the bias complications of the feedback integrator.     

Asymptotically Stable Motions of a Gyro in a Spinning Vehicle

An analysis of the motion of a single-axis rate gyroscope mounted in a space vehicle which is spinning with uncertain constant angular velocity xz about the spin axis of the gyro is presented. The nonlinearity in the equation of motion of the gimbal is retained. Using the Lyapunov approach, regions are obtained in the k-xz plane where k is the torsional spring constant, for asymptotic stability and for global asymptotic stability, and an estimate of the region of stability in state space is presented. Analytical relations for the selection of the gyro parameters are derived.     

直升机起落架的集成计算

直升机起落架常规计算包括停机状态计算及减缩质量计算、静态性能计算及主、尾起落架的着陆性能计算.要完成这些计算需要整机及起落架的诸多数据.在研制过程中,为了获得最优的设计,需要对起落架的各参数进行不断调整,对计算结果进行反复分析和比较,计算量较大,数据处理较为繁复耗时.详细阐述如何采用Excel和Matlab对起落架的常规计算进行集成.为完成一种直升机起落架的常规计算,采用该集成方法,编制了2000余行的M代码.在惠普Z800计算机平台下运行,耗时400余秒即可完成所有相关计算.输入输出的数据存储在同一Excel文件,文件中各项参数和计算结果数据可直接用于查阅、校对、分析,也可再编辑.     

Dynamic characteristics of a cyclic-periodic structure with a piezoelectric network

This paper deals with a cyclic-periodic structure with a piezoelectric network. In such a system, there is not only mechanical connection but also electrical connection between adjacent periodic sectors. The objective is to learn whether the presence of a piezoelectric network would change the dynamic characteristics of the system. The background of the research is about vibration reduction of a bladed disk in an aero-engine, and the system is simulated by a lumped parameter model. The dynamic equations of the system are derived, and then the analytical solution corresponding to the eigenvalue problem is given. The vibration responses to single traveling wave excitations(EO excitations) and multiple traveling wave excitations(NEO excitations) are studied.The results show that the presence of a piezoelectric network would change the natural frequencies of the system compared with those of the system with the piezoelectric shunt circuit. The forced response is sensitive to the connection type and the elements of the network. An energy analysis of the electro-mechanical coupling system has been performed to understand its dynamic behavior,and the following conclusion is obtained: a vibration reduction to excitations whose primary harmonic component is not zero can be achieved by a parallel piezoelectric network, while a reduction to other excitations should be based on a series piezoelectric network.     

Collapse of a spheroidal cavitation bubble near a solid wall

Dynamics of a gas bubble in a liquid near a solid wall is studied. The influence of the initial spheroidal disturbances of the bubble shape and the distance to the wall on the dynamics of the bubble–liquid system is analyzed. The pressure in the bubble is initially greater than that of the surrounding liquid. An algorithm based on the Euler scheme and the boundary element method is applied in the calculations.     

Magnetohydrodynamic simulation of a streamer beside a realistic coronal hole

Existing models of coronal streamers establish their credibility and act as the initial state for transients. The models have produced satisfactory streamer simulations, but unsatisfactory coronal hole simulations. This is a consequence of the character of the models and the boundary conditions. The models all have higher densities in the magnetically open regions than occur in coronal holes (Noci,et al., 1993).     

带升力风扇的垂直起降推进系统建模研究

为了填补国内对转升力风扇研究与垂直起降系统建模研究相结合的空缺,分别针对常规与对转升力风扇,建立了垂直起降推进系统的部件级实时数学模型,并进行了性能对比。针对减阻的要求,通过插值将升力风扇进气道的阻力系数选为0.0470;针对升力风扇非设计点特性准确性的要求,采用基元级理论对风扇进行半设计半计算;特别引入中介推力修正系数(κ)用于对转风扇的参数设计,该方法下两升力风扇推力相等,轴功率偏差为0.0265。进一步的动态仿真表明,由于风扇特性的影响,同样工况下非设计点处对转风扇的升力和轴功率更大;并且由于升力风扇与发动机的耦合性,针对不同升力风扇的差异性,发动机会通过调整转速而产生"趋同"的作用效果。