适用于RTM成型聚酰亚胺树脂的合成与性能研究

使用4-苯乙炔苯酐(4-PEPA),2,3,3′4′-联苯四酸二酐(a-BPDA),1,4-双(4′-氨基-2′-三氟甲基苯氧基)苯(BTPB)和1,4-对苯二胺(p-PDA)合成了两种苯乙炔苯酐封端的聚酰亚胺低聚物PI-1和PI-2,并对低聚物的熔体粘度稳定性和热性能等进行系统研究.实验结果表明:采用热亚胺化方法制备的低聚物具有很高的产率(＞99%);PI-1低聚物在280℃时表现出低的熔体粘度(＜1Pa.s)和良好的熔体粘度稳定性,可用于RTM成型工艺制备树脂基复合材料;PI-1和PI-2低聚物经371℃固化后显示了优异的热性能,玻璃化转变温度超过400℃(DMA法,tanδ值),5%热失重温度超过520℃.     

新型聚苯并噁嗪改性树脂的制备与性能

通过预聚反应制备了一种新型聚苯并噁嗪改性树脂.利用FTIR、GPC表征了改性树脂.利用旋转黏度计、DSC、DMA和TGA分别考察了树脂的流动性能、固化行为和改性树脂固化物的热性能.结果表明:制备的苯并噁嗪改性树脂在60～ 100℃,黏度小于500 mPa·s,恒温6h黏度不明显增大,具有良好的流动性能,适用于RTM成型工艺.改性树脂聚合温度较低,具有良好的固化工艺性.改性树脂固化物在氮气气氛下Td5在430℃以上,在900℃的残重高达73.71％,Ts为353.4℃,具有良好热性能.     

苯乙炔苯酐封端聚酰亚胺低聚物的合成与性能

将4-苯乙炔苯酐(4-PEPA)和3,3',4,4'-二苯醚四酸二酐(ODPA),与3,4'-二氨基二苯醚(3,4'-ODA)和1,4-双(4'-氨基-2'-三氟甲基苯氧基)苯(BTPB)或1,3-双(4-氨基苯氧基)苯(1,3,4-APB)混合物通过高温缩合聚合反应合成了两种苯乙炔苯酐封端的聚酰亚胺低聚物PI-1和PI-2,对其熔体黏度、热行为及固化物的热性能等进行了研究.实验表明,PI-1和PI-2低聚物在280℃时具有低的熔体黏度(＜1 Pa·s)和良好的熔体黏度稳定性;经371℃固化后形成的纯树脂固化物具有优异的耐热性能,5%热失重温度超过520℃,Tg超过330℃,有望成为适用于RTM工艺的复合材料基体树脂.     

耐371℃PMR-Ⅱ型聚酰亚胺树脂化学反应特性的研究

利用TGA、DSC、IR和DMTA等现代分析手段考察了PMR－Ⅱ型聚酰亚胺树脂KH－305－50A（长期使用温度达371℃/1000h)的化学反应特性，研究结果表明，该含氟的耐高温树脂在加热过程中发生了一系列复杂的化学反应，在115℃-300℃之间进行了酰胺化和酰亚胺化反应，生成了聚酰亚胺预聚体；280℃-470℃该预聚体发生加成型的交联固化反应，且在370℃－380℃之间固化反应最快。     

增韧双马来酰亚胺与烯丙基苯并噁嗪共混物的性能

以间甲苯胺、烯丙基双酚A和多聚甲醛为原料合成了一种烯丙基型苯并噁嗪(BA-mt).将其与二苯甲烷型双马来酰亚胺、烯丙基双酚A (DABPA)以不同比例进行熔融共混,得到了增韧双马来酰亚胺与烯丙基苯并噁嗪的共混物BDB.用DSC对共混物的固化反应进行研究,用DMA和TGA研究了固化树脂热性能,结果表明,在BMI/DABPA中加入BA-mt后,固化树脂的热性能下降,但氮气氛中T10d仍高于400℃,800℃残炭率提高到33％以上.加入10份BA-mt改性BMI/DABPA的固化树脂的Tg为319℃;其弯曲性能提高,弯曲强度为44 MPa,弯曲模量为3.76 GPa.BMI/DABPA/BA-mt固化树脂的吸水率随BA-mt的加入而下降.     

RTM复合材料结构件用BMI树脂基体6421体系的研究

介绍了一种ＲＴＭ复合材料结构件用ＢＭＩ树脂基体６４２１,研究了该树脂的基本物理性能和固化工艺,同时给出了复合材料的性能。６４２１树脂具有良好的工艺性及物理性能,其复合材料能在１８０℃以上使用。     

二烯丙基双酚 A 共聚双马来酰亚胺改性氰酸酯树脂的性能

采用二烯丙基双酚A和二苯甲烷型双马来酰亚胺与双酚A型氰酸酯共聚,以改善氰酸酯树脂的工艺和耐热性能;利用DSC,TGA,DMA表征了树脂的固化行为和耐热性能;此外,还研究了树脂的力学性能及高频下的介电性能。结果表明,改性后的氰酸酯树脂固化反应温度降低了约60℃,改性树脂固化物在氮气气氛下Td5约400℃,Tg约270℃,显示了良好的耐热性能。在7~15 GHz宽频范围下,改性树脂的介电常数3,介电损耗0.008~0.01,显示了良好的介电性能。     

MT300/802双马树脂基复合材料固化工艺及高温力学性能

采用热分析方法研究高活性802双马树脂的固化反应动力学特征,分析树脂固化度与固化温度、固化时间的关系,确定树脂固化制度150℃/1 h+180℃/2 h+200℃/4 h,制得MT300/802复合材料200℃固化T_g达到325℃,而相同固化温度XU292双马树脂T_g仅为234℃。进一步考察MT300/802复合材料室温、230、280及300℃的力学性能,结果表明,复合材料单向板280℃弯曲强度保持率达到了57%,300℃弯曲强度仍达到1 094 MPa,室温及高温层间剪切强度及面内剪切强度也表现出较高的性能水平,高活性802双马树脂及其复合材料固化温度相对较低而使用温度较高,能够满足航天领域耐高温主承力结构的应用要求。     

高韧性异构聚酰亚胺树脂及其复合材料

采用MPMR合成技术得到了低黏度、高韧性、耐高温异构聚酰亚胺树脂,该树脂预浸液常温储存期大于两个月,亚胺化后纯树脂在320℃熔体黏度<300 Pa·S,树脂浇铸体的弯曲强度>100 MPa,弯曲模量>3.0 GPa,抗拉强度可达80 MPa,断裂伸长率可达6%,固化后T5d>500℃,其中PI-4复合材料在300℃的弯曲强度保持率达到76.5%.     

低温固化非热压罐成型树脂及其复合材料性能

通过DSC、红外光谱、流变仪和力学性能测试等方法,研究了 3228树脂及T700/3228预浸料的性能.结果表明:3228树脂初始固化温度为67.9℃,峰值固化温度为89.5℃;在60℃时具有大于2 h的低黏度平台期,黏度值在20～30 Pa·s;温度大于65℃后表现出低温快速固化的特性;采用60℃预固化1 h,80℃...     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。