Nb-Si-Mo三元系合金相图

 Nb/Nb5Si3原位复合材料是一种有望替代镍基超合金用做飞机发动机叶片的新一代超高温结构材料。采用非自耗电弧熔炼技术制备出不同成分的Nb/Nb5Si3原位复合材料,利用X射线衍射仪、扫描电镜和能谱仪对Nb-Si-Mo三元系合金的相组成和微观组织进行研究。结果表明：Nb-Si-Mo三元系部分液相面投影图（<37.5 at% Si）含有4个初生相区,其立体相图中存在2个液固四相平衡反应和1个固态四相平衡反应。在2个液固四相平衡反应面之间存在一个三相共晶平衡棱柱,成分位于该棱柱内的合金会通过L→Nbss+β-Nb5Si3反应凝固生成Nbss/β-Nb5Si3片层共晶。     

Liquid-Solid Phase Equilibria of Nb-Si-Ti Ternary Alloys

To determine the liquid-solid phase equilibria of the Nb-Si-Ti ternary system, Nb-Si-Ti alloys of different compositions are prepared. By means of scanning electron microscopy （SEM）, X-ray diffraction （XRD） and electron probe microanalysis （EPMA）, the phases in the alloys, such as Si-based solutions, Ti（Nb）Si, Ti（Nb）Si2, Nb（Ti）Si2, Ti（Nb）5Si4, Nb（Ti）5Si3, Ti（Nb）5Si3, Nb（Ti）3Si and Nb-based solutions are identified, and the phase evolution is analyzed. As a result, the microstmctural and microchemical evidence provides a clear definition of the Nb-Si-Ti liquidus surface projection and indicates that the ternary phase diagram has seven transition reactions.     

Mo含量对Mo-Ni-B堆焊合金组织和性能的影响

设计制备了Mo-Ni-B系合金粉块新材料,采用TIG堆焊工艺在Q235钢基体上制备Ni基三元硼化物堆焊合金。研究了合金粉块中Mo含量对三元硼化物堆焊合金层组织、物相、硬度、耐磨性、耐蚀性的影响。结果表明,堆焊金属主要由三元硼化物Mo2M’B2、Mo Ni4、Mo5(B、Si)3、γ-(Fe,Ni,Mo,Cr)等相组成;Mo含量对堆焊合金的显微组织有较大影响;随着合金粉块中Mo含量的增加,堆焊合金和三元硼化物的显微硬度均明显下降;在所研究堆焊合金中,Mo 44.18%的耐蚀性最好,Mo 37.53%的堆焊合金的耐磨性能是Q235钢的27.7倍。     

铌钨合金材料在液体火箭发动机上的应用

为探索铌钨合金在液体火箭发动机上的应用，针对我国研制成功的Nb-5W-2Mo-1Zr铌钨合金进行了高温性能试验及抗高温氧化涂层的研制，铌钨合金及涂层在高温时的组织结构分析及相关工艺试验。结果表明：Nb-5W-2Mo-1Zr铌钨合金及抗氧化涂层可用于液体火箭发动机。     

Si和Ti对Nb-6Hf-4Zr-2B合金组织和室温力学性能的影响

 为了寻求Nb合金的强度和塑性的平衡,设计了以Nb基固溶体Nbss为主导相的Nb-xSi-6Hf-4Zr-2B-yTi(x=4,8;y=10,30;原子分数)合金,研究了Si和Ti对合金组织和室温力学性能的影响。结果表明,合金由Nbss、Nb3Si和Nb5Si3等3相组成。4Si-(10,30)Ti合金铸态组织是Nb枝晶和分布在枝晶间的硅化物(Nb3Si和Nb5Si3),8Si-(10,30)Ti合金Nb枝晶间分布的是Nb/硅化物(Nb5Si3)的共晶和Nb3Si,随着Si和Ti含量的增加,硅化物体积分数增加。1 600 ℃退火50 h可使部分Nb3Si共析分解,改变合金的组织形貌和各相的体积分数。随着Si和Ti含量的增加,合金的硬度和强度增加,但塑性和韧性降低。Nb枝晶的失效方式为解理断裂,而硅化物为脆性断裂。     

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-22Ti-14Si-2Hf-2Al-xCr Alloys

Nb-22Ti-14Si-2Hf-2Al-xCr (x=2, 6, 10, 14, 17 at%) alloys are prepared by arc-melting under argon atmosphere. Microstructural characteristics, mechanical properties and oxidation resistance of the arc-melted alloys are investigated. At 2 at% Cr content, the microstructure is composed of Nbss, Nb3Si and a small quantity of Nb5Si3, when the Cr contents increase, Nb3Si disappears. For the high Cr content (x ≥ 10 at%) alloys, besides the Nbss and Nb5Si3, Cr2Nb is also detected. With the increase of Cr content, the volume fractions of Cr2Nb and Nb5Si3 increase, while that of Nbss increases firstly and then begins to degrade when the Cr content is higher than 6 at%. For the alloy with 2 at% Cr, the room temperature fracture toughness is about 14.5 MPa·m1/2, but badly decreases to about 8.5 MPa·m1/2, when the Cr contents increase. Vickers hardness of Nbss tends to increase linearly from about 400 to 500, while that of silicides is not sensitive to Cr contents, about 950. The appearance of Cr2Nb phase significantly improves the high temperature oxidation resistance of the alloys with high Cr contents. The isothermal oxidation tests show that the oxidation kinetics of the alloys with various Cr contents follows parabolic oxidation kinetics.     

合金化及热处理对Fe_3Al合金组织和性能影响

研究了不同的热处理条件及添加Mn,Mo,Nb,Cr,V,RE（La-Ce）等合金元素对Fe3Al合金组织和性能的影响。结果表明,Fe3Al合金在B2相区间保温淬火后的硬度值较小,在DO3相区短时间回火硬度值大幅增加,随回火时间延长硬度值呈降低趋势,在本实验的最长回火时间内（50h）硬度稍有提高;TEM分析表明,这与回火过程中DO3畴的尺寸变化有关;合金化后Cr和V的加入降低合金硬度,其它几种元素都提高了合金的硬度;SEM分析表明合金元素的作用机理不同：Cr软化了合金,Mo主要产生固溶强化,Mn、V、Nb加入后有第二相析出,RE元素主要偏析在晶界,细晶强化。     

Hf对Nb15W5Si2B合金室温和高温力学性能的影响

 为了寻求Nb-Si基合金高温强度和室温塑性之间的平衡,设计了以Nb基固溶体相Nb-SS占主导的Nb15W5Si2BxHf(x= 0,5,10,15,原子百分数）合金,研究了Hf元素对Nb15W5Si2B合金的组织、室温和高温压缩性能以及高温蠕变性能的影响。结果表明,Nb15W5Si2B合金由Nb-SS和Nb5Si3两相组成,Nb5Si3相呈网状分布;Hf的加入不改变相组成,但Nb5Si3相由网状分布逐步变成不连续小岛状分布,而且体积分数减少。Hf同时提高Nb15W5Si2B合金的高温静强度和室温塑性,但对Nb15W5Si2B高温压缩蠕变性能不利。最后讨论了Hf对Nb15W5Si2B合金强化与塑性化机理。     

Nb-10Si合金室温断裂韧性研究

利用真空电弧熔炼制备了处于亚共晶区的Nb-10Si-xMo(x=5,15)复合材料,采用扫描电子显微镜(SEM)和X射线衍射(XRD)分析了在1200℃退火100h后复合材料的微观组织形貌、相组成和断口形貌,并测定了Nb-10Si-Mo复合材料的显微硬度。用单边切口悬臂梁法(SENB)研究了加入合金元素后复合材料室温韧性的变化。深入分析了合金元素对材料韧性相变形行为和复合材料室温断裂韧性的影响。     

合金元素Al对Cr-20Nb合金高温抗氧化性能的影响

采用机械合金化＋热压烧结工艺制备了掺杂合金元素Al的Cr-20Nb合金,研究Al对Cr-20Nb合金在1100℃和1200℃下高温抗氧化性的影响。结果表明,合金元素Al能促进Cr-20Nb合金氧化时生成AlNbO4复合型氧化物,该复合型氧化物能有效抑制Cr2O3,的挥发反应,从而改善Cr2O3,氧化层的致密性,并提高氧化膜的粘附性,导致合金抗氧化性显著提高。不同Al含量的Cr-20Nb合金氧化增重均近似于抛物线规律。     

Effects of B on the Microstructure and Oxidation Resistance of Nb-Ti-Si-based Ultrahigh-temperature Alloy

Nb-Ti-Si-based ultrahigh-temperature alloys concocted with boron ranging from 0 to 2 at% are prepared by arc-melting technology. The effects of adding boron on their as-melted microstructure and oxidation resistance are analyzed. The (Nb,Ti)ss, β-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ exist in Nb-22Ti-16Si-6Cr-3Al-4Hf alloy, while (Nb,Ti)ss, α-(Nb,Ti)₅Si₃ and γ-(Nb,Ti)₅Si₃ are present in Nb-22Ti-16Si-6Cr-3Al-4Hf-1B and Nb-22Ti-16Si-6Cr-3Al-4Hf-2B alloys. The oxidation of Nb-Ti-Si-based ultrahigh-temperature alloys is dominated by the diffusion of oxygen through (Nb,Ti)ss. Compared to boron-free alloys, the boron-containing alloys have significantly lower oxidation rate when oxidized at 1 200 °C for less than 50 h, but, for more than 50 h, their oxidation resistance deteriorates.     

Nb521 铌钨合金组织性能及其应用研究

对我国新研制的Nb521铌钨合金的室温及高温性能进行了研究,并对相应的微观组织进行了分析,并结合其在液体火箭发动机推力室身部的应用情况。结果表明:该铌钨合金具有优异的工艺性能及高温性能,可满足发动机对材料性能的使用要求。     

热处理对9 Cr13 Mo3 Co3 Nb2 V组织与硬度的影响

采用金相分析、硬度测试等技术手段,研究热处理对马氏体不锈钢9Cr13Mo3Co3Nb2V组织和硬度的影响。结果表明：9Cr13Mo3Co3Nb2V经淬火、冰冷处理及多次回火后,残余奥氏体充分转变为回火马氏体,并产生较强的二次硬化效果,进而获得稳定的组织和高的硬度;在350℃以上回火时,由于组织中二次碳化物的析出,开始出现二次硬化倾向,至480~520℃时,回火硬度达到了最大值。     

Effects of Nb Content on Yield Strength of NiTiNb Alloys in Martensite State

Two near single-phase NiTiNb alloys—Ni₅₀Ti₄₈Nb₂ and Ni_49.5Ti_46.5Nb₄—are prepared and studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), differential scanning calorimetry (DSC) and tensile tests in order to unearth the effects of Nb-atom solid solution in NiTi phase on the yield strength induced by self-accommodation of martensite variants. The results show that the yield strength of near single-phase NiTiNb alloys varies inversely with the amount of Nb-atoms solid-dissolved in NiTi phase. From the results out of the prior and current studies, it can be surmised that the effects of Nb content on the yield strength of NiTiNb alloys in martensite state depend on the coaction. Nb solid solution weakening mechanism and β-Nb phase composite strengthening mechanism. This inference might be a satisfactory explanation to the fact that the yield strength of (NiTi)_50–0.5xNb_x alloys in martensite state begins with decline and then rises when the Nb content increases.     

TiNiFeNb形状记忆合金的组织结构及相变特性

通过向TisoNiso合金中加入Fe和Nb元素,制备出一种四元Ti49Ni50-xFexNb1形状记忆合金.采用X射线衍射和背散射电子衍射的方法,测试和分析了合金的相结构及微观组织形态,采用电阻法系统研究了合金的相变特性.结果表明:Nb元素的加入并没有改变TiNiFe合金的B2结构,仅导致了广极少量的富Nb相在基体中析...     

新型Co基合金Co-9Al-(9-x) W-xMo-2Ta-0.02B的显微组织与高低温力学性能

以新型Co基合金Co-9Al-9W-2Ta-0.02B成分为基础,分别添加了原子分数为2％、4％、6％、9％的Mo元素替代W（分别称2Mo、4Mo、6Mo、9Mo合金,W+Mo的原子分数为9％,无Mo添加的称为0Mo合金）,研究了Mo元素对合金相组成、显微组织形貌、维氏硬度和高低温压缩强度的影响.结果表明铸态合金由Co...     

Microstructure and Magnetic Anisotropy of FeCoNbB Films

Effect of Nb contents on microstructure and magnetic properties of FeCoNbB films has been studied. X-ray diffraction (XRD) analysis reveals that Nb plays a role in refining grain and in facilitating formation of amorphous structure. When Nb content is more than 8 at%, the films transform from crystalline to amorphous structure, accompanied by variations in magnetic properties. An unusual out-of-plane anisotropy component is consequently observed. It can be suggested that the anisotropy induced by increasing Nb contents be attributed to stress-related magnetoelastic anisotropy. The undesirable anisotropy is greatly reduced by thermal annealing, reducing film thicknesses or applying an external magnetic field together with Si addition.     

金属间化合物NiAl合金蠕变行为的研究

系统研究了热等静压态(HIP)NiAl-9Mo,NiAl-Cr(Zr),NiAl-28Cr-5.5Mo-0.5Hf-0.02wt%P合金与定向凝固NiAl-28Cr-5.8Mo-0.2Hf,NiAl-28Cr-5.5Mo-0.5Hf,NiAl-28Cr-5Mo-1Hf,NiAl-Fe(Nb)共晶合金的高温拉伸蠕变行为.研究结果表明,七种NiAl合金具有相似的蠕变曲线,表现为较短的减速蠕变阶段和较长的稳态蠕变阶段及较高的蠕变应变.在高温低应力下蠕变变形主要受位错攀移过程控制,在低温高应力下蠕变变形主要由Orowan机制控制.NiAl合金的蠕变断口表现为塑性断裂和沿胞界断裂的混合特征.NiAl合金蠕变断裂主要受蠕变裂纹扩展所控制,蠕变断裂数据符合Monkman-Grant关系.     

Electron Beam-Physical Vapor Deposited TiAl-based Laminated Composite Sheet with Nb Layer Toughening

The TiAl-based laminated composite sheet of 150mm×100 mm×0.2mm, with 24 TiAl layers and 23 Nb layers laid alternately one on another, was successfully fabricated using the electron beam-physical vapor deposition (EB-PVD) method. The microstructure and properties of the sheet were investigated on an atomic force microscope (AFM), a scanning electron microscope (SEM) and a tensile testing machine. The results indicate that the evenly distributed Nb layers are well joined with the TiAl layers, and the interfaces between layers are transparent, and every interlayer spacing is of about 8 μm. The fractures appear to be a mixture of intergranular fractures and somewhat ductile quasi-cleavage ones. Despite its slight influence on ultimate tensile strength, the inserts of Nb layers efficiently in-crease the room temperature ductility of TiAl-based alloys due to the crack deflection effect.     

Cr对Nb-16Si-22Ti-2Al-2Hf合金显微组织与高低温力学性能的影响

 以Nb-16Si-22Ti-2Al-2Hf成分为基础,分别添加了2%和17%(原子分数,后同)的Cr元素替代Nb(分别称2Cr和17Cr合金),研究了Cr含量对Nb-16Si-22Ti-2Al-2Hf合金相组成、显微组织形貌、室温断裂韧性和高温强度的影响,分析了高低温失效机制。结果表明,铸态和1 375 ℃×100 h热处理后2Cr合金由Nbss和Nb₅Si₃两相组成;当Cr含量为17%时,出现了具有C15结构的Laves Cr₂Nb相,合金由Nbss、Nb₅Si₃和Cr₂Nb三相组成,热处理后在Nb₅Si₃中还析出了球状Cr₂Nb相。随着Cr含量由2%提高到17%,热处理合金的室温断裂韧性K_Q由14.32 MPa·m^1/2下降到10.30 MPa·m^1/2。合金强度与Cr含量的关系受温度影响,随Cr含量提高,室温和1 150 ℃时合金的硬度或强度增高,而1 250 ℃和1 350 ℃时合金强度降低。如1 150 ℃时2Cr和17Cr合金的屈服强度σ_0.2分别为349 MPa和387 MPa;1 350 ℃时分别为306 MPa和74 MPa。