Parylene C薄膜微波电路的应用可行性研究

针对三防材料在微波电路中多余物防控方面的可行性、可靠性问题,提出在产品表面用真空化学气相沉积法镀Parylene C薄膜,结果表明该膜层可有效控制直径d小于1 mm的可动多余物,提高微波产品PIND(颗粒碰撞粒子检测)测试的合格率.同时与焊接、胶粘、互联、清洗等配装工艺有良好的适配性,且满足可靠性要求.该薄膜较高的绝缘...     

一种发射筒用防热涂料的制备与表征

为了解决现有发射筒内壁用防热涂料脆性大、附着力差等问题，本文以有机硅改性环氧树脂为基体，添加多种耐高温填料，聚酰胺为固化剂，制备了一种防热涂料，并对其耐焰耐热性能、“三防性”、热老化性能等进行了全面的表征分析。结果表明该涂料能够承受200~300 ℃的长时高温，900 ℃下烧蚀10 s内涂层无变化，且其附着力、“三防性”优良。     

航天器用Parylene-C涂覆材料空间辐照适用性研究

派瑞林（Parylene）薄膜主要用于功率电刷的三防,确保电功率的稳定传输。本文对两种规格（17和27 μm）Parylene薄膜的厚度、热性能、绝缘性能、在铍青铜上的附着性能以及耐空间辐照性进行了研究。结果表明：通过真空气相沉积法制备的Parylene-C涂覆材料厚度误差可控在2 μm内;膜层在铍青铜上的附着力等级为1级,薄膜热分解温度为453 ℃,两种厚度薄膜击穿电压分别为3.65 kV（17 μm）和5.27 kV（27 μm）;经2.5×10¹⁵ p/cm²质子辐照后,膜层外观均完好,附着性能、热性能、绝缘性能仍满足工程使用需求;经2.5×10¹⁶ e/cm²电子辐照后,膜层出现严重开裂、起皮现象。对电子辐照前后膜层的热性能、红外结构等进行了进一步的研究,分析了电子辐照后膜层的失效机理并获得了Parylene-C涂覆材料膜层耐空间电子辐照上限为1×10¹⁴ e/cm²。     

Parylene真空涂覆新工艺研究

简述了Parylene真空沉积的机理,并对采用Parylene真空涂覆的涂层样件进行了全面的性能摸底试验。     

军用电子产品三防技术的发展和工艺改进

阐述了现代军用电子设备的三防设计和工艺实施,并介绍了一些新的三防技术,以及对传统三防工艺的改进方法。     

我所火控产品的三防标准化

本文概要介绍了我所对火控产品进行三防(防锈、防霉、防盐雾)设计和处理,最后编制成包括材料选择,不耐腐蚀材料的三防处理、表面涂覆、整机三防工艺内容的17项企业标准的情况。     

空空导弹弹体结构三防设计浅析

空空导弹的三防密封设计是提高其可靠性的重要环节.本文主要讨论了弹体结构设计中的三防结构设计技术,主要从设计准则、密封方法、防腐蚀方法以及典型工艺几个方面进行综合论述.通过对多种腐蚀形式的分析,结合目前空空导弹弹体结构的现状,提出了系统进行三防设计的思路.     

离子镀Ti(N,C)耐磨镀层成分与性能研究

 用空心阴极离子镀技术,在常用的不锈钢(1Cr18Ni9Ti)基材上,镀制Ti(N,C)耐磨镀层。对镀层的成分进行了分析,讨论了镀层成分的耐磨性,显微硬度和附着力的影响。通过对Ti(N,C)镀层与TiN和TiC镀层性能的对比,肯定了Ti(N,C)复合化合物镀层具有更优越的耐磨性和附着力。     

飞机防冰表面材料研究进展

结冰不仅给人们的日常生活带来诸多不便,而且影响飞机的飞行安全,甚至引起重大的经济问题和人身威胁。虽然飞机的防/除冰研究已经进行了数十年,但仍然需要开发出对环境无害、经济且有效的防冰策略。防冰表面材料可通过延长结冰时间和降低冰的附着力减轻甚至消除冰的积聚,是目前飞机防/除冰领域学科发展的前沿方向,制备高性能防冰表面材料具有十分重要的意义。本文综述了当前防冰表面材料的研究现状,对超疏水材料以及润滑层材料等应用于防冰领域的优劣势进行分析,并分析与展望了防冰材料的发展方向。     

C/E表面镀Al膜的原子氧试验

为了提高C/E复合材料的导电性及耐空间环境的能力,应用电弧离子镀技术在C/E复合材料表面沉积了A l膜,研究了地面模拟原子氧环境对C/E复合材料表面镀A l前后的侵蚀、质损及A l膜的附着力、导电性的影响。通过XRD、SEM、FT-IR、万能拉伸测试仪、FZ-82数字式四探针测试仪等测试分析样品。结果表明:电弧离子镀A l膜微米级以上颗粒较多,但分布均匀,膜层致密,附着力达2 N/mm2以上;原子氧对C/E复合材料侵蚀明显,镀铝后具有明显的防护作用;原子氧侵蚀后的A l膜电阻率有所上升,但还是有较好的导电性;辐照后的A l膜附着力比辐照前反而增加,其机理尚待进一步研究。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。