Capacitive-loaded push-pull parallel-resonant converter

Results of a theoretical and experimental investigation of a capacitive-loaded push-pull parallel-resonant DC-DC converter (CL-PPRC) are presented and discussed. The push-pull parallel-resonant converter (PPRC) is driven by a lower-than-resonance frequency and the secondary voltage is rectified and smoothed by a capacitive filter. The CL-PPRC is shown to operate in the zero voltage switching (ZVS) mode with a boost-like DC transfer ratio that is approximately linear with the period of the switching frequency. Experimental results of a 180 W, high output voltage (1.8 KV) prototype are found to be in good agreement with the analysis, models, and simulation results presented. The basic characteristic of ZVS, the fact that the resonant current is passing through the switches only during a fraction of the period, the high-voltage transfer ratio, and the inherent input/output (I/O) isolation, make the proposed topology a viable design alternative in avionic and aerospace applications     

Current-fed multiresonant isolated DC-DC converter

A novel topology, current-fed multiresonant dc-dc converter (CF-MRC) was studied theoretically and experimentally. The new topology differs from previously described current-fed push-pull parallel-resonant topologies in the fact that the output is coupled to the current of the resonant inductor and in the addition of a second capacitor across the transformer. The main features of the proposed converter are an inherent protection against a short and open circuit at the output, a high voltage gain and zero voltage switching (ZVS) over a large range of output voltage. These characteristics make it a viable choice for applications, such as a high voltage capacitor charger, that require controllable current sourcing over a wide output voltage swing.     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer     

A 10 kW DC-DC converter using IGBTs with active snubbers

This full bridge DC-DC converter employs zero voltage switching (ZVS) on one leg and zero current switching (ZCS) on the other. This technique produces exceptionally low insulated-gate bipolar transistor (IGBT) switching losses through the use of an active snubber that recycles energy back to the source. Experimental results are presented for a 10-kW, 20-kHz converter     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

基于TMS320F2812生成移相PWM的2种办法

移相 PWM波是很多开关电源常用的驱动脉冲信号。双向全桥直流变换器(Bidirectional-Full-Bridge DCDC Converter,BDC)在双重移相控制方式下时需要 4组两两互补的移相 PWM波。文章基于 TMS320F2812型 DSP(Digital Signal Processor)分析了 2种生成移相 PWM的方法。为提高双向全桥直流变换器工作的安全性和可靠性,为移相 PWM波设置死区时间。对所提出的方法进行测试后结果良好,对于双向全桥直流变换器闭环控制系统的构建具有重要意义。     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

New ZVT-PWM DC/DC converters using active snubber

A novel active snubber soft switching method is proposed. The unique location of the resonant inductor and capacitor ensures low current and voltage stresses in the converter. An analytical study of a boost dc-dc converter with the proposed active snubber method is presented in detail to illustrate its operation principles and design considerations. By simple modification, this soft switching method is also suitable for ac-dc boost topology, especially for high power-factor-correction (PFC) universal interface applications. A 500 W prototype system has been made to simulatively and experimentally verify the performance of the soft switching.     

Analysis and design of a three-phase LCC-type resonant converter

A three-phase dc-to-dc LCC-type resonant converter with high-frequency transformer isolation is proposed. The operation and a simple analysis of the converter are presented. Design curves are obtained and a design example is given. SPICE simulation and experimental results are presented to verify the performance of the proposed converter for varying load conditions. The converter proposed has several advantages, e.g., operation in lagging PF mode for the entire load range, requires a narrow variation required in switching frequency, reduced component size and stresses, etc     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

A novel resonant converter topology for DC-to-DC power supply

A class-E DC-to-DC converter with half-wave controlled current rectifier is proposed. Its output voltage is controlled by the conduction angle of the rectifier switch at constant switching frequency. Zero voltage switching for all the switches can be maintained from full load to no load. Its steady state characteristics are analyzed and the effects of the circuit parameters are studied. Some extensions of the proposed converter are also discussed. The analysis is verified by PSPICE simulation and an experimental prototype     

Boost变换器软开关技术的研究

提出一种新型有源软开关技术,在辅助开关和谐振电路的作用下,可以实现开关电源中开关管的零电压开通和零电压关断,而且可以减小开关管的电压应力和电流应力。对电路工作原理和参数设置进行了分析,给出了关键参数的选取原则。利用实际电路,验证了有源软开关技术的有效性。     

High-power, light-weight power conditioning

After a review of light-weight transformer efforts in the US, a weight analysis is carried out. From basic transformer relations and geometrical considerations it is shown how transformer specific power should scale with power and frequency. The result compares well with design results for frequency scaling but not for power scaling. After refinements for variations of voltage, cooling technique, power (while voltage is held constant) and current density, an algorithm is presented that agrees well with the results of adiabatic transformer designs and with vapor cooled transformer designs. Transformer specific powers as low as 0.01 kg/kW are predicted at an operating frequency of 20 kHz. Caution is advised in the use of the algorithm because few of the transformers with which the algorithm is compared have actually been considered. The SDI/AF/NASA megawatt converter program is discussed, and results of Phase I are summarized     

永磁同步电机有限集模型预测直接转矩控制

针对永磁同步电机(PMSM)模型预测直接转矩控制(DTC)转矩脉动大、功率元件开关频率不恒定等问题,将两电平逆变器的8个电压空间矢量作为有限控制集,应用到PMSM DTC中。设计考虑转矩误差、最大转矩电流比及电流约束的成本函数,利用成本函数来估算有限集合中各电压矢量的占空比,从而求得逆变器的最优电压矢量作为系统控制量。与传统模型预测控制方法相比,该方法的电流谐波和转矩脉动显著降低,且转矩动态性能也得到改善。仿真试验结果验证了所提出的控制方案有效性。     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

Robust controller design for a series resonant converter

Because of their reduced switching losses, allowing a higher operating frequency, dc-to-dc resonant converters have been used extensively in the design of smaller size and lighter weight power supplies. The steady state and dynamic behavior of both the conventional series and parallel resonant converters have been thoroughly analyzed and small-signal models around given nominal operating points have been obtained. These models have been used in the past to design controllers that attempted to keep the output voltage constant in the presence of input perturbations. However, these controllers did not take into account either load or components variations, and this could lead to instability in the face of component or load changes. Moreover, prediction of the frequency range for stability was done a posteriori, either experimentally or by a trial and error approach In this paper we use μ-synthesis to design a robust controller for a series resonant converter (SRC). In addition to robust stability the design objectives include rejection of disturbances at the converter input while keeping the control input and the settling time within values compatible with a practical implementation     

Ultracapacitors + DC-DC converters in regenerative braking system

An ultracapacitor system for an electric vehicle has been implemented. The device allows higher accelerations and decelerations of the vehicle with minimal loss of energy and minimal degradation of the main battery pack. The system uses a DC-DC power converter, which is connected between the ultracapacitor and the main battery pack. The design has been optimized in weight and size, by using water-cooled heat sinks for the power converter, and an aluminum coil with air core for the smoothing inductance. The ratings of the ultracapacitor are: nominal voltage: 300 Vdc; nominal current: 200 Adc; capacitance: 20 Farads. The amount of energy stored allows us to have 40 kW of power during 20 seconds, which is enough to accelerate the vehicle without the help of the traction batteries. The vehicle uses a brushless DC motor with a nominal power of 32 kW and a peak power of 53 kW. A control system based on a Digital Signal Processor (DSP) manipulates all the aforementioned variables and controls the Pulse Width Modulation (PWM) switching pattern of the converter transistors. The car used for the implementation of this system is a Chevrolet LUV truck.