Surge and Noise Generation in a Forward DC-to-DC Converter

Switching surge and noise voltages are analyzed under the common-mode condition in a forward dc-to-dc converter. The analysis is performed by partitioning the switching time into several states and introducing the high-frequency equivalent circuits. The equivalent circuits include not only inductive and capacitive parameters, but also the parameters related to the switching speed of the transistor and the recovery characteristics of the diode. As a result, the effects of these various parameters on the surge and noise generation are made clear quantitatively.     

Optimum Design of RC Snubbers for Switching Regulators

The optimum design of an RC snubber to suppress the surge voltage across the transistor in a switching regulator with a two-winding reactor is presented. Analyzing the surge voltage by means of high-frequency equivalent circuits, we obtain the third-order characteristic equation. This third-order equation is first analyzed by the aid of the root locus method. As a result, the region where the surge voltage can be suppressed is described in the R-C plane. Then considering the snubber loss, the optimum resistance and capacitance can be obtained. Second, the precise design procedure of RC snubbers is discussed by normalization and numerical calculations. This procedure is summarized in easy-to-use nomographs.     

Half-bridge neutral point diode clamped rectifier for power factor correction

A high power factor rectifier based on neutral point clamped scheme is proposed. The voltage stress of each power semiconductor of the adopted rectifier is equal to the half dc bus voltage instead of full dc link voltage in the conventional switching mode rectifier. The control signals of the power switches are derived from the dc link voltage balance compensator, line current controller, and dc link voltage regulator. The hysteresis current control scheme is employed to draw a clean sinusoidal line current, high input power factor, regulated dc link voltage, and balance capacitor voltages. Three voltage levels are generated on the ac terminal of the adopted rectifier. To verify the proposed operation scheme, performance characteristics are given by the experimental results.     

航空发动机进气道出口截面喘振波的分布

用扰流插板使涡扇发动机进气道内产生不对称分布的总压畸变并使发动机出现喘振。在进气道出口即发动机进口截面测取两种不同转速下发动机的喘振压力波。应用小波分析奇异点理论,采用模极大值原理和高阶Daubechies小波多尺度分析,对喘振压力信号进行处理,得到发动机喘振波在其进口截面的波形分布特征。揭示了在两种转速下,喘振波在截面上的分布相似,其频率和幅值与转速成正比。截面中心部分表现为正脉冲,周围部分为负脉冲。在垂直方向上的幅值较大,而两翼较小。对该分布特征进行了分析,初步的推论为:高压压气机引起喘振,稳态压力畸变最严重的区域和未受到畸变扰动的区域,喘振波最为强烈。     

Multiplier Offset Voltages in Adaptive Arrays

The effects of multiplier offset voltages in adaptive arrays are examined. Multiplier offset voltages arise when active circuits are used to implement the error-by-signal multipliers required in an array based on the LMS algorithm. These offset voltages are known from experimental work to have a strong effect on array performance. It is first shown how multiplier offset voltages may be included in the differential equations for the array weights. Then their effect on weight behavior is studied. It is found that the offset voltages affect the final values of the weights, but not the time constants. Furthermore, the effect they have is influenced by the amount of element noise in the array. An adequate amount of noise is necessary to minimize weight errors due to offset voltages. An example is treated to show the effect of offset voltages on the final array weights and the output signal-to-noise ratio (SNR). With offset voltages present, it is found that there is a maximum SNR that can be obtained from the array. A specific input SNR is required to obtain this maximum output SNR. Finally, it is shown that a finite operating range for the weights places a further restriction on the acceptable values of offset voltages and noise.     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

基于试车试验的涡轴发动机整机喘振裕度研究

某涡轴发动机在外场使用过程中,由于进气环境的影响和多发不同的装机位置等因素,致使发动机出现偶发喘振或前喘征兆等现象。为此,对原型机转子进行改进设计。同时,采用试车试验的方法,测算并验证改型机的整机喘振裕度。结果表明:在整个工作范围内,改型机的整机喘振裕度得到了全面提升,设计点喘振裕度由10.65%提高至16.21%。试验可为该系列发动机设计制造和改进使用提供数据参考。     

Modeling and Design of Switching Regulators

Various building blocks of a switching regulator are described in detail and mathematical models are developed for all building blocks in terms of transfer functions, which enable one to design a switching regulator for stability, desirable bandwidth, line rejection, and transient response. A step-by-step procedure to design compensation is illustrated using two examples. Various networks for compensation and their transfer functions are presented which the author hopes will be very handy to use and will become the reference source.     

进口动态总压流场对燃机稳定性裕度影响

为了得到某燃机发生喘振的原因,在燃机进口进行了动态流场测试,对流场中存在的较大涡旋尺度、较大瞬间动态压力畸变以及与进口涡壳共振产生的转速基频脉动等动态流场特点进行了详细研究,获得了进口动态总压流场特点.试验数据和资料分析表明:进口动态流场的特点使发动机稳定裕度损失加大,从而造成发动机喘振.      

发动机喘振-爆燃故障的信号分析

本文着重介绍某双轴发动机喘振—爆燃故障用 FFT信号处理机进行诊断和信号分析的方法。文章结合发动机在湍流动态畸变流场下的喘振—爆燃试验研究,介绍了试验设备、测量系统和对发动机“故障”信号分析的结论。湍流型动态畸变流场下的压气机喘振多为“漂移型”喘振,表现有随机性。发动机对动态畸变流场的敏感度远高于稳态畸变。利用 FFT信号分析技术进行故障诊断,有广泛应用价值。它较其它方法精确、迅速、简便。      

Modeling the Full-Bridge Series-Resonant Power Converter

A steady state model is derived for the full-bridge series-resonant power converter. Normalized parametric curves for various currents and voltages are then plotted versus the triggering angle of the switching devices. The calculations are compared with experimental measurements made on a 50 kHz converter and a discussion of certain operating problems is presented.     

Adaptive Input Filter Compensation for Switching Regulators

An input filter is frequently employed between a switching regulator and its power source. However, its presence often results in degradation of dynamic performances and stability. The detrimental interaction is between an input filter and a switching regulator and is a function of the input filter parameters and also of the supply voltage. An earlier paper presented an analysis and design procedure aimed at developing a feed-forward loop to cancel this undesirable interaction. The feed-forward design is extended here to encompass a scheme that automatically accounts for changes in the supply voltage; the result is an adaptive compensation that tracks the input voltage variations. Experimental results are presented that confirm the adaptive nature of the design.     

On Lyapunov stability analyses of the switching regulator/filtersystem

The stability design criteria for the fourth-order switching regulator/low-pass filter system are obtained directly from the solution to the resultant simultaneous equations for the Lyapunov matrix equation. The regulator/filter system is asymptotically stable if the values of the filter components are chosen to satisfy the derived Lyapunov stability design criterion for a given value of the switcher dynamic resistance     

Frequency-Domain Analysis of Switching Closed-Loop Regulators

An accurate analysis of a switching voltage regulator power stage is performed by eliminating the mathematical unrigorousness of the averaging technique. The differential equations are solved for the ON and OFF intervals to obtain the exact mean values in function of the values at the beginning and at the end of the intervals. The accurate relation is used for the integral of the derivative forming the left member of some equations. A flyback regulator power stage is analyzed as an example. Some considerations are made concerning the regulator compensation using a two-loop control circuit.     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

基于滑模控制的航空发动机多变量约束管理

针对航空发动机传统单变量线性控制器min-max切换方法处理约束的不足,提出了单变量滑模控制器替换所有线性控制器的改进策略,并将该方法拓展为新切换逻辑下的多变量滑模控制结构。基于改进的单变量滑模控制器min-max结构,多变量控制策略中加入了多变量滑模主控制器和新的切换逻辑,充分利用发动机的所有控制量,克服了传统方法的保守性,进一步提高发动机约束下的动态性能。对稳态时工作的控制器进行了理论分析,建立了多变量控制器实现精确跟踪的充要条件。仿真结果表明,多变量控制方法在更苛刻的约束条件下能够实现跟踪任务,而且提高了推力跟踪的快速性,调节时间从1.91 s缩短到1.54 s,同时降低了稳态时的油耗。     

基于dSPACE的永磁同步电机低振动噪声控制策略

为降低变频器供电引起的永磁同步电机(PMSM)电磁振动噪声,首先理论分析了变频器引入的PMSM振动噪声源,然后利用MATLAB/Simulink建立仿真模型,通过dSPACE进行编译并控制一台PMSM,比较了随机开关频率调制技术和死区补偿技术降低振动噪声的优缺点,提出一种混合随机开关频率死区补偿技术。试验结果表明,此方法综合随机开关频率调制技术和死区补偿技术的优点,能降低逆变器引入电流谐波引起的中低频振动噪声和逆变器开关频率与电流谐波相互作用引起的高频振动噪声。     

微机电陀螺解调过程中的噪声传递机理研究

微机电陀螺的噪声性能是衡量陀螺综合性能的重要指标之一,不仅与陀螺本身机械结构有关,还与其测控电路有着密切联系。本文将通过理论推导计算出噪声经过乘法解调和开关解调时的传递机理,指出开关解调会使解调信号中的谐波成分和解调输入噪声向解调后的基带中进行混叠,相对于纯正弦解调会增大噪声,最后应用LabVIEW软件进行纯软件仿真和半实物仿真验证,并通过实际测试数据证明其正确性,为陀螺解调方案的选择提供依据。     

混合型逆变器的空间矢量调制策略优化

高速永磁同步电机驱动系统具有电磁时间常数小、高速区载波比低的特征,加剧了电流纹波,影响系统效率、振动噪声和电磁干扰。为降低高速永磁同步电机的电流纹波,基于SiC-MOSFET/Si-IGBT混合型逆变器设计了一种改进型低损耗空间矢量调制算法。首先,通过调整零电压矢量的生成方式和各功率器件的开关动作时序,将大部分开关动作转移至低损耗的SiC-MOSFET中,并为高损耗的Si-IGBT提供零电压开关条件,降低了逆变器损耗,提高了驱动系统的效率和可用开关频率,逆变器开关频率的提高有效降低了电机电流纹波。其次,对该算法作用时的电流纹波特性进行深入分析,在此基础上提出一种变开关频率模式的最优交轴电流纹波峰值调制算法以优化交轴电流纹波性能。然后,根据预测的交轴电流纹波峰值实时调整载波频率,通过削峰填谷的方式对交轴电流纹波进行平均,在不增加开关损耗的条件下,分散开关能量、降低转矩脉动、改善振动噪声和电磁兼容性能。所提方案的优势在于：较于传统型逆变器,逆变器开关损耗降低、效率提高,可进一步提升开关频率以改善电流纹波;较于传统空间矢量调制算法,改进了电压矢量的生成方式,并利用载波频率这一新增自由度分散能量,降低了交轴电流纹波。最后,通过仿真与实验对所提出算法的有效性进行了验证。     

An Adaptive-Control Switching Buck Regulator-Implementation, Analysis, and Design

Describing-function techniques and averaging methods have been employed to characterize a multiloop switching buck regulator by three functionsl blocks: power stage, analog signal processor, and pulse modulator. The model is employed. to explore possible forms of pole-zero cancellation and the adaptive nature of the control to filter parameter changes. Analysis-based design guide lines are provided including a suggested additional RC-compensation loop to optimize regulator performances such as stability, audiosusceptibility, output impedance, and load transient response.