激光选区熔化成形TC4钛合金激光焊接头组织与力学性能

对3mm厚激光选区熔化成形(SLM)TC4钛合金对接接头进行了激光焊接工艺试验,研究了80J/mm和100J/mm两种能量输入对接头焊缝成形、微观组织及接头力学性能的影响.结果表明,在两种不同焊接能量输入条件下,激光焊接SLM成形TC4钛合金获得良好的焊缝成形,焊缝区的平均显微硬度分别为388.7HV及403.3HV,...     

ZTC4合金电子束焊接接头显微组织及力学性能研究

以ZTC4钛合金电子束焊接接头为研究对象,通过显微硬度试验、金相分析以及常规力学性能试验,讨论了电子束焊接接头不同位置的组织、形态差异,探究显微组织与接头显微硬度的相关性,以及电子束焊接接头的拉伸性能和冲击性能。通过组织分析及显微硬度测试发现,ZTC4合金电子束焊缝微观组织由原始β相转变为针状α'相,即针状马氏体,其热影响区组织为片状α相与原始β相的混合物,且焊缝处显微硬度最高,热影响区其次,母材最低。通过力学性能测试发现,电子束焊接接头的拉伸和冲击性能与母材相当,说明采用电子束焊接ZTC4可以得到力学性能良好的焊接接头。     

TC4-DT钛合金线性摩擦焊接头组织特征及其形成机制

研究TC4-DT损伤容限型钛合金线性摩擦焊(linear friction welding,LFW)接头的组织特征及形成机制。利用光镜和扫描电镜对接头各区域微观组织进行表征,利用显微硬度计测试接头的显微硬度分布。结果表明:接头焊缝区(WZ)发生动态再结晶,焊接过程中WZ温度超过β转变点,焊后快冷的条件下发生了β→α′及β→α两种相变并析出了大量α′马氏体以及二次层片α;TC4-DT钛合金母材(BM)组织具有较高的变形抗力,使得接头形成的热力影响区(TMAZ)较窄。TMAZ内组织在强烈的热力耦合作用下拉长变形并破碎,焊后快冷的条件下析出少量α′马氏体及大量二次层片α;毗邻TMAZ的热影响区(HAZ)基本保留了BM不同位向的α集束的组织特征,但受热的影响α集束内α/β相界两侧元素相互扩散,层间β消耗,初生α长大;WZ组织的细晶强化和第二相强化,TMAZ组织的应变强化和第二相强化,以及HAZ内α相的长大使得接头上述区域显微硬度均高于BM。     

异种状态TC4 钛合金电子束焊接性能分析

针对相对疏松的铸造钛合金和相对密实的锻造钛合金的焊接问题,开展了两种状态的TC4钛合金电子束焊接工艺研究,对比了不同焊接参数对焊接质量的影响。研究结果表明,采用方波扫描可以较好地实现铸造钛合金与锻造钛合金的连接,焊缝成形良好,内部无缺陷;焊接接头力学性能分析表明,拉伸断裂位置全部在铸件母材区一侧。实焊结果证明,电子束焊接可以实现异种状态TC4钛合金焊接的工程化应用。     

异种状态TC4钛合金电子束焊接性能分析北大核心CSCD

针对相对疏松的铸造钛合金和相对密实的锻造钛合金的焊接问题,开展了两种状态的TC4钛合金电子束焊接工艺研究,对比了不同焊接参数对焊接质量的影响。研究结果表明,采用方波扫描可以较好地实现铸造钛合金与锻造钛合金的连接,焊缝成形良好,内部无缺陷;焊接接头力学性能分析表明,拉伸断裂位置全部在铸件母材区一侧。实焊结果证明,电子束焊接可以实现异种状态TC4钛合金焊接的工程化应用。     

大厚度TC4-DT钛合金电子束焊接接头微观组织和力学性能研究

对60mm厚TC4-DT钛合金锻件进行电子束焊接。通过对焊接接头显微组织观察,拉伸、冲击、断裂韧性测试,研究了该合金电子束焊接接头的力学性能。结果表明:TC4-DT钛合金具有良好的焊接工艺性能。焊缝为α相网篮组织,该合金电子束焊接接头的拉伸强度与基材相当,但冲击韧性与锻件相比略低。同时,该合金焊接接头也具有良好的损伤容限性能,与锻件相比焊接接头的断裂韧性下降约20%。     

热处理对激光快速成形TC21钛合金组织和硬度的影响

采用激光快速成形技术制备出TC21钛合金块状坯料,研究了去应力退火及固溶时效热处理对成形件组织和硬度的影响。结果表明:去应力退火后,成形件组织和显微硬度基本无变化;固溶+时效热处理后,原沉积态明暗两区统一,硬度基本无差别,表明组织已均匀化。随着固溶温度的升高,网篮组织中的α片变宽,球状α相的数量增多,晶界α相发生粗化。当固溶温度为932℃时,成形件沉积态中粗大的柱状晶发生再结晶,转变为较细小的等轴晶。     

TC4钛合金薄板高能束焊接接头疲劳性能研究

对TC4钛合金薄板激光焊和电子束焊接头的疲劳性能进行了试验研究,测试了不同应力水平下的疲劳寿命。采用统计分析的方法研究了TC4钛合金薄板母材及其高能束流焊接接头的中值疲劳寿命。分析了焊接工艺条件对接头疲劳强度的影响。结果表明,在高应力水平时,TC4钛合金高能束流焊接接头的疲劳寿命低于母材的疲劳寿命,在低应力水平时,TC4钛合金高能束流焊接接头的疲劳寿命高于母材的疲劳寿命。     

钛合金激光焊接研究现状

随着航空工业的发展,钛合金在航空结构中有着越来越广泛的应用。焊接作为重要的连接手段,其制造接头的力学性能决定了构件的使用性能。激光焊接具有高能束焊接方法热输入小、残余应力及变形小的特点,焊接质量高,并且能在开放环境中开展工作,已成为真空电子束焊接外另一种优秀的钛合金焊接方法,是近年研究的热点。总结了近期钛合金激光焊接的一些研究工作,重点介绍了关于激光焊接钛合金组织性能调控方面的成果,并讨论了钛合金激光焊所存在的问题,具体内容包括：激光类型和扫描方式对接头质量的影响、三种典型(α型、α+β型和β型)钛合金激光焊接头组织性能特点、焊后热处理对钛合金激光焊接头组织性能调控方法。为采用激光焊接方法制造高质量钛合金接头研究工作提供参考。     

TC18钛合金焊接接头应用性能研究

采用氩弧焊和电子束焊2种焊接工艺对TC18锻坯进行焊接,按焊接接头试验方法进行了拉伸和冲击试验,获得了焊接接头的强度系数和冲击韧性。试验结果表明,TC18钛合金焊接接头具有良好的焊接性,同时,对于飞机焊接结构设计应优先选用电子束焊。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.