共查询到17条相似文献,搜索用时 187 毫秒
1.
2.
3.
4.
基于主动约束层阻尼结构及独立模态振动控制方法,利用压电驱动器/传感器和粘弹性材料与薄板构成的复合层压阻尼结构,在理论研究的基础上^[1],对一组悬壁板结构进行了试验研究,给出了部分试验研究结果,分析总结了主动约束层阻尼结构的主要优缺点。 相似文献
5.
6.
7.
压电智能桁架的振动控制和结构的一体化优化设计 总被引:2,自引:1,他引:2
提出了压电智能桁架的振动控制和结构的一体化优化设计方法。在优化模型中既能考虑结构设计指标,又能考虑振动控制指标,并且能同时进行控制参数和结构设计参数的联合优化设计,给出了灵敏度计算和优化求解方法,数值算例表明了本文方法的有效性。 相似文献
8.
9.
10.
用于直升机振动控制的主动调谐式吸振器研究 总被引:3,自引:0,他引:3
振动问题是直升机设计中的难题,会导致机体结构疲劳、舒适性降低和高噪声等问题。通常的单桨叶控制方案由于受压电驱动器机电性能的限制而难以实现。智能弹簧是一种采用单桨叶控制原理的主动调谐式吸振器,它通过压电驱动器自适应控制桨叶根部的结构阻抗,达到振动控制目的。建立了智能弹簧的简化模型,对其谐波响应控制特性进行研究;采用频率分析和数字信号合成技术产生参考信号,在DSP平台上设计自适应陷波算法对智能弹簧驱动器组件进行控制;模拟和风洞实验结果均表明智能弹簧能够在较宽频率范围内对桨叶的谐波响应进行有效控制,验证了通过主动阻抗控制实现直升机桨叶振动控制的可行性。 相似文献
11.
随着遥感卫星光学成像设备等精度的不断提升,其对振动环境的要求也在不断提高,简单的线性被动Stewart平台已经无法满足苛刻使用要求。提出了一种新型基于多边形膜片弹簧与压电致动器复合的一体化主被动Stewart减振平台,其单自由度元件主要由多边形膜片弹簧、压电致动器、力传感器以及柔性铰链组成。相较于传统线性隔振器存在的高静刚度和低动刚度之间的固有结构矛盾,所提出的多边形膜片弹簧作为隔振器的关键原件,兼具高静-低动(HSLD)特性,能够使隔振系统同时具备较高的静态刚度进行静态承载以及较低的动刚度进行动态减振。为了降低被动隔振系统中存在的共振峰幅值,本文在被动膜片弹簧元件的基础上串联一个压电致动器与力传感器组成的主动控制元件进行主动振动控制。仿真结果表明,采用比例积分力(PIF)反馈控制算法的主动控制系统,在频域上不仅可以通过积分力环节搭建出天棚阻尼的效果来降低共振峰峰值(11.19 dB),而且其比例-力环节可等效为增大了质量矩阵项,能够有效降低减振系统的固有频率(20.9 Hz),拓宽其减振带宽,并同时能维持高频段的高衰减性,在时域上也能够将系统的加速度振动幅值从±0.6g降低至±0.07g,振动衰减达88%。 相似文献
12.
具有电磁约束阻尼层梁的振动主动控制研究计算(英文) 总被引:2,自引:0,他引:2
Niu Hongpan Zhang Yahong Zhang Xinong* Xie Shilin MOE Key laboratory for Strength Vibration Department of Engineering Mechanics School of Aerospace Xi’an Jiaotong University Xi’an China 《中国航空学报》2008,21(2):115-124
This paper investigates vibration control of beam through electro-magnetic constrained layer damping (EMCLD) which consists of electromagnet layer, permanent magnet layer and viscoelastic damping layer. When the coil of the electromagnet is electrified with proper control strategy, the electromagnet can exert magnetic force opposite to the direction of structural deformation so that the structural vibration is attenuated. A mathematical model is developed based on the equivalent current method to calculate the electromagnetic control force produced by EMCLD. The governing equations of the system are obtained using Hamilton's Principle and then reduced with the assumed-mode method. A simulation on vibration control of a cantilever beam is conducted under the velocity proportional feedback to demonstrate the energy dissipation capability of EMCLD, and the beam system with the same parameter is experimented. The results of experiment and simulation are compared and the results show that the EMCLD is an effective means for suppressing modal vibration. The results also indicate that the beam system has better control performance for larger control current. The EMCLD method presented in this paper provides an applicable and efficient tool for the vibration control of structures. 相似文献
13.
Wei LIU Mengde ZHOU Zhengquan WEN Zhuang YAO Yu LIU Shihong WANG Xiaochun CUI Xiao LI Bing LIANG Zhenyuan JIA 《中国航空学报》2019,32(9):2109-2120
In wind tunnels, long cantilever sting support systems with low structural damping encounter flow separation and turbulence during wind tunnel tests, which results in destructive low-frequency and big-amplitude resonance, leading to data quality degradation and test envelope limitation. To ensure planed test envelope and obtain high-quality data, an active damping vibration control system independent of balance signal based on stackable piezoelectric actuators and velocity feedback using accelerometer, is proposed to improve the support stability and wind tunnel testing safety in transonic wind tunnel. Meanwhile, a design of powerful sting-root embedded active damping device is given and an active vibration control method is presented based on the mechanism analysis of aircraft model vibration. Furthermore, a self-adaptive fuzzy Proportion Differentiation(PD) control model is proposed to realize control parameters adjustment automatically for various testing conditions. Besides, verification tests are performed in laboratory and a continuous transonic wind tunnel. Experimental results indicate that the aircraft model does not vibrate obviously from -4° to 11° at Ma = 0.6, the number of useable angle-of-attack has increased by 7° at Ma = 0.6 and 5° at Ma = 0.7 respectively, satisfying the requirements of practical wind tunnel tests. 相似文献
14.
15.
16.
以压电陶瓷为作动器,并采用独立模态控制法,对冲击载荷作用下的大柔度悬臂梁前三阶模态进行了振动主动控制研究。实验结果表明,使用独立模态控制方法,能有效地抑制悬臂梁的振动,控制效果非常明显。采用模态滤波和相移控制器进行模态分离和相位调节,可获得最大结构阻尼,取得良好的动态控制效果。 相似文献
17.
An approach is presented to the control of an uncertain nonlinear flexible robot arm (PUMA-type) with three rotational joints. The third link is assumed to be elastic. A torquer control law, which is a function of the trajectory error, is derived for controlling the joint angles. The knowledge of the system dynamics is not required for the derivation of the controller. This controller includes a reference model to generate command joint angle trajectories, and a dynamic system in the feedback path which requires only joint angle and rate for feedback. The torquer controller asymptotically decouples the elastic dynamics into two subsystems, representing the transverse vibration of the elastic link in two orthogonal planes. For the damping of the elastic vibration, a force control law using modal velocity feedback is synthesized. Simulation results are presented to show that the combination of the torque and force control law accomplishes reference joint angle trajectory tracking and elastic mode stabilization despite the uncertainty in the system 相似文献