Zr对Ti3Al基金属间化合物TLP扩散焊接头组织性能的影响

采用TiZrNiCu非晶态箔状钎料过渡液相(TLP)扩散连接Ti3Al基金属问化合物,通过对接头的力学性能及微观结构的分析,研究了中间层合金TiZrNiCu中Zr元素对Ti3Al基金属间化合物,TLP扩散连接接头组织和性能的影响规律和机理.结果表明,在连接工艺相同条件下,随着中间层合金中添加元素Zr含量减小,Ti3Al基TLP扩散焊接头强度增大;通过延长后续扩散处理时间,可以减小Zr元素对接头组织性能的不利影响.     

镍基合金中间层TLP连接MGH956合金接头组织分析

分析了采用KNi9镍基合金中间层TLP连接MGH956合金时焊接接头组织、成分、相组成与连接工艺的关系;概述了焊接缺陷形成机理,并优化了工艺参数.研究结果表明:在连接温度T为1 240℃,保温时间t为480min条件下能够形成连续的焊接接头.     

DD3单晶合金瞬间过渡液相扩散焊接头组织与性能

采用粉状中间层合金D1P和非晶态箔状中间层合金D1F对镍基单晶高温合金DD3进行了TLP扩散焊,并对接头组织与性能进行了分析研究。试验结果表明,D1P粉状中间层合金TLP扩散焊接头中存在明显的组织不均匀现象,经过高温长时间保温才可消除,而采用D1F非晶态箔状中间层合金TLP扩散焊DD3合金更易获得与母材组织一致的接头。在合适的规范下,两种中间层合金扩散焊的DD3合金接头980℃持久强度均达到或超过母材的90%。     

SiCp/101铝基复合材料铜中间层TLP扩散焊工艺研究

通过颗粒增强铝基复合材料的铜中间层TLP扩散连接试验,对接头性能的影响因素进行了研究,并采用扫描电镜和电子探针等手段分析了接头连接机理、微观组织与接头性能的关系,从而确定了其试验条件和焊接规范.     

连接参数对Ti53311S 高温钛合金TLP 连接接头性能的影响

采用Cu作为中间层实现了Ti53311S合金的TLP连接,通过SEM、EDS方法分析了接头界面的微观组织,研究了接头界面微观组织及力学性能随TLP连接温度及保温时间的变化规律。结果表明:TLP连接接头的典型界面结构为Ti53311S/β-Ti/Ti、Cu(Sn)金属间化合物/β-Ti/Ti53311S。随着TLP连接温度的升高或保温时间的增加,焊缝宽度逐渐增加,Cu元素向母材侧的扩散程度更加充分,化合物相分解消失,接头室温抗拉强度先大幅升高后趋于稳定,连接工艺为980℃/20 min时,接头抗拉强度达到最大值899 MPa。     

SiCp/101铝基复合材料铜中间层TLP

通过颗粒增强铝基复合材料的铜中间层TLP扩散连接试验 ,对接头性能的影响因素进行了研究 ,并采用扫描电镜和电子探针等手段分析了接头连接机理、微观组织与接头性能的关系 ,从而确定了其试验条件和焊接规范。     

过渡液相扩散焊连接工艺参数对DD407母材液化的影响

为了将瞬间液相扩散焊的液相形成过程与固相扩散焊复合,充分利用TLP及固相扩散焊的优点,需要研究接头界面处母材液化规律。选用DD407镍基单晶高温合金作为试验材料,中间层合金采用含B为3.5%的BNi9进行TLP连接,观察母材液化宽度和接头宽度在不同工艺参数下的变化。通过分析得到:母材液化区宽度随着加热温度升高及保温时间增长而增加,在焊接温度为1100℃,保温时间为5min,中间层厚度为150μm的情况下,母材液化的宽度达到65.8μm;中间层厚度对母材液化的影响程度相对较大,主要降熔元素B的总量增加;TLP连接过程中,母材液化的过程为降熔元素B不断向母材中扩散,导致母材液化宽度增加,但随着扩散的进行,B元素的含量逐渐降低引起等温凝固,从而在一定程度上影响了表面清理的效果。     

SiC颗粒增强Al基复合材料焊接工艺研究

通过SiC颗粒增强Al基复合材料与Al合金的焊接工艺试验研究，重点分析了材料组合，保湿工艺，连接时间等工艺参数对连接接头性能的影响以及连接接头的微观组织及成分分布，研究表明，TLP扩散连接是一种适用于复合材料连接的重要方法，在相同工艺条件下，LF6／SiCp-6061Al的接头性能明显优于LF6／SiCp-2024Al，连接时间过短或过长，都将影响到接头性能，并且连接时间对不同材料组合的影响也不同，采用二次保温工艺可以较大幅度地提高接头性能。     

脉冲电流辅助粉末夹层TLP连接SiC_p/Al接头微观组织和力学性能

研究脉冲电流辅助瞬间液相(Transient Liquid Phase,TLP)扩散连接技术,采用粉末中间层,利用低压高强脉冲电流通过铝基复合材料搭接面与中间层,从而实现对SiC_p/2024Al复合材料板材的TLP扩散连接。分析不同工艺参数下连接试样的微观组织和力学性能,探索脉冲电流对铝基复合材料连接的影响机理。结果表明:采用真空压强为1×10~(-3)Pa,平均电流密度115 A/mm~2,连接预紧压力为0.5 MPa,连接时间60 min条件下,连接接头形成了良好的冶金连接界面,无缺陷产生;通过对连接接头微观组织观察发现,在脉冲电流作用下,接头原位生成弥散的高强度高硬度金属间化合物增强相,有效地提高了接头的力学性能。     

不同热处理制度下Ti–22Al–25Nb合金惯性摩擦焊接头显微组织分析

采用惯性摩擦焊连接Ti2AlNb合金,分析了焊态和热处理后焊接接头的组织变化,研究了不同热处理制度对Ti2AlNb合金惯性摩擦焊接头显微组织的影响.结果表明:利用惯性摩擦焊技术可获得无缺陷、焊缝状态良好的Ti–22Al–25Nb合金焊接接头;温度和热处理时间共同决定了焊合区O相的数量和尺寸的变化,但是相比时间的变化,热...     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.