共查询到20条相似文献,搜索用时 359 毫秒
1.
2.
3.
4.
5.
《航空精密制造技术》2014,(1)
针对大型结构件曲面外形的特点,研发一套基于激光跟踪仪的大型结构件外形辅助测量装置。该测量装置以夹持靶标的直角三坐标伺服机构为测量机构,以导航小车为测量机构的载体,通过激光跟踪仪实时反馈靶标位置进行误差补偿,实现直角三坐标伺服机构的闭环控制,提高了测量精度。 相似文献
6.
7.
8.
9.
激光用于靶场测量具有测量精度高和单站独立定位等优点。由于在飞行目标上安装激光合作目标,激光跟踪测量始终是合作目标部位,这就避免了由于跟踪飞行体部位差异而引起的测量误差。因为是光学测量,光波长比无线电的厘米波还要短四个量级,因而对激光测距的大气折光修正和仰角折光修正要比无线电波的精确得多。我国首先在战略武器飞行体上加装角反射器激光合作目标,用激光测量其初始段或再入段飞行轨迹。我们从七十年代初就开始研究靶场激光测量,不仅在各种电影经纬仪上成功地加装了激光测距系统,在连续波微波雷达上也加装成功。对导弹目标的激光测距,在初始段 相似文献
10.
11.
Differential GPS on board naval vessels has been tested in severe multipath archipelago environment against a commercial laser tracker system. The average location difference was 3 meters and two periodic error components were found. Their tune constants were 1.8 and 28 seconds and the peak amplitudes 1.5 and 1.1 meters, respectively. In addition to these, a clear dependency of location error standard deviation figures on the GPS antenna mounting distance from the sea level was observed. 相似文献
12.
提出了在复合材料飞机部段装配过程中采用无余量装配的方法。在产品设计和制造过程中采用数字量传递的方式可减少误差积累,提高协调精度。关键零部件的装配、工装制造等采用激光跟踪仪等数字化测量设备可以确保精确性,并能在装配工艺设计阶段就考虑零部件间的协调安装精度及公差分配要求。通过分析复合材料部段装配特点,并以复合材料机身典型结构为例进行应用研究,阐述了在三维数字化装配过程中具有协调关系的关键零部件无余量装配的工艺流程、方法,从而可实现零部件一次装夹、加工及无反复装配,使装配质量具有良好的稳定性。 相似文献
13.
14.
Auto-normalization algorithm for robotic precision drilling system in aircraft component assembly 总被引:2,自引:0,他引:2
A novel approach is proposed to detect the normal vector to product surface in real time for the robotic precision drilling system in aircraft component assembly, and the auto-normalization algorithm is presented based on the detection system. Firstly, the deviation between the normal vector and the spindle axis is measured by the four laser displacement sensors installed at the head of the multi-function end effector. Then, the robot target attitude is inversely solved according to the auto-normalization algorithm. Finally, adjust the robot to the target attitude via pitch and yaw rotations about the tool center point and the spindle axis is corrected in line with the normal vector simultaneously. To test and verify the auto-normalization algorithm, an experimental platform is established in which the laser tracker is introduced for accurate measurement. The results show that the deviations between the corrected spindle axis and the normal vector are all reduced to less than 0.5°, with the mean value 0.32°. It is demonstrated the detection method and the auto-normalization algorithm are feasible and reliable. 相似文献
15.
头盔显示器(HMD)定位是扩展现实系统应用中必不可少的关键过程,其定位的准确程度直接决定了三维注册的精度。文中以典型的基于六自由度跟踪器和光学透视型HMD的扩展现实系统为例,分双目和单目两种情况详细介绍了HMD的定位方法。 相似文献
16.
简要介绍了传统飞机全机水平测量方法的优缺点,以及激光跟踪仪系统(Laser Tracker System)测量的基本原理,并对水平测量的可行性进行了讨论。 相似文献
17.
18.
对由AGV承载的工业机器人组成的AGV式移动制孔机器人的定位误差补偿方法进行了研究。在面向飞机装配的AGV式移动制孔机器人系统中,利用激光跟踪仪构建坐标系,提出了AGV式移动制孔机器人机座坐标系的换站方法,能更好地适应飞机制造多品种、小批量的特点。基于对AGV式移动制孔机器人定位误差源的分析,利用定位误差相似性,提出针对AGV式移动制孔机器人的基于反距离加权定位误差的空间插值与补偿方法,克服了现有技术对于AGV式移动制孔机器人定位误差补偿的局限性。以AGV搭载的KUKA KR480型工业机器人制孔系统作为试验对象,通过试验选取最优网格步长,补偿结果表明,能将系统综合定位误差平均值由补偿前的1.045 mm降低到0.227 mm,最大绝对定位误差由补偿前的2.727 mm降低到0.478 mm,降低了82.47%,该方法能有效提高AGV式移动制孔机器人的绝对定位精度。 相似文献
19.
本文以定位器支撑的大部件调姿系统为研究对象,通过激光跟踪仪测得大部件上多个测点坐标数据.针对各点在不同坐标系下测量点值不匹配且各点精度要求有差异的问题,提出了最小二乘法评估大部件位姿的模型,并利用权值实现对多个测点数据进行误差分配优化,为大型部件的位置姿态评估计算提供一套有效的解决方案. 相似文献
20.