共查询到20条相似文献,搜索用时 359 毫秒
1.
高比强低密度的Al—Li合金 总被引:1,自引:0,他引:1
本文对Al-Li合金的基本特性和近来国外研制动态进行了综述。高比强、低密度的新型Al-Li合金是一代大有希望的新型航天、航空材料。在发达国家中该合金的研制与生产发展迅猛,但目前在研制和生产中仍存在许多问题有待进一步研究。为满足我国航天、航空工业发展的需要,加速研制和生产Al-Li合金,已势在必行。 相似文献
2.
Al-Li合金是一种比强度高、比刚度大的新型轻合金,它在宇航工业中具有很大的应用潜力。本文论述了Al-Li合金化,分析了Al-Li合金的生产方法、性能及其最新发展。 相似文献
3.
4.
刘北兴%覃耀春%李仁顺 《宇航材料工艺》2001,31(3):49-51
研究了分级时效工艺对1420Al-Li合金组织与性能的影响,试验结果表明经70℃/12h+120℃/4~10h工艺分级时效处理可使1420Al-Li合金的综合力学性能得到显著的提高;分级时效工艺使1420Al-Li合金析出的δ′相粒子分布均匀、尺寸细小。 相似文献
5.
XU Yue a WANG Xiaojing a YAN Zhaotong b LI Jiaxue a a School of Chemistry Environment Beihang University Beijing China b Institute of Nuclear Physics Chemistry China Academy of Engineering Physics Mianyang China 《中国航空学报》2011,24(5):681-686
The intergranular corrosion and exfoliation corrosion of 2195 Al-Li alloy treated by multi-step heating-rate controlled aging (MSRC) are studied. The corrosion features of 2195 Al-Li alloys which are respectively treated by high-temperature nucleation MSRC (H-M) and low-temperature nucleation MSRC (L-M) are contrasted. And the corrosion mechanism of 2195 Al-Li alloy is also discussed from the viewpoint of microstructure (types, distribution, etc.) of the strengthening phase. The results show that 2195 Al-Li alloy after H-M is more susceptible to intergranular corrosion and exfoliation corrosion than that of alloy after L-M. The degree of intergranular corrosion increases with the increase of predeformation amount and the surface parallel to the rolling direction is more prone to exfoliation corrosion. The main reason of intergranular corrosion and exfoliation corrosion is the for-mation of corrosion galvanic couples among T1 phase, ?θ’ phase and grain boundary precipitate-free zones (PFZ). 相似文献
6.
电场均匀化对 2091Al-Li 合金的显微组织及力学性能的影响 总被引:1,自引:0,他引:1
应用扫描电镜(SEM)及电子探针(EPMA)研究了强电场作用下Al-Li合金的均匀化过程。实验结果表明,强电场加速了2091Al-Li合金的均匀化过程,但是随着电场作用时间的增加,发生了镁、铜原子的上坡扩散,导致镁、铜原子的非平衡偏聚。因此,电场及非电场的联合处理方法是一个有效的均匀化处理制度。同时,还研究了强电场均匀化对显微组织及力学性能的影响,发现强电场均匀化促进T1相的形核,抑制δ‘和S’相析出,提高了Al-Li合金的屈强比。 相似文献
7.
定向凝固时热溶质对流对Al/AlLi共晶生长形态稳定性的影响 总被引:1,自引:1,他引:0
在垂直向上定向凝固条件下,研究了热溶质对流对二元亚共晶 Al-Li合金 Al/ Al Li共晶生长形态稳定性的影响。结果表明,晶体生长初期,热溶质对流较微弱,对界面形态稳定性无明显的影响,晶体以完全的Al/ Al Li共晶方式生长。当热溶质对流较强烈时,对界面形态稳定性产生严重的影响。平面界面失稳破开时,单相胞状晶领先生长。在单相胞状晶之间以 Al/ Al Li共晶方式生长。获得了二元亚共晶 Al-Li合金共晶的稳定性生长条件。 相似文献
8.
9.
The Forming Limit Curve (FLC) of the third generation aluminum-lithium (Al-Li) alloy 2198-T3 is measured by conducting a hemispherical dome test with specimens of different widths. The theoretical pred... 相似文献
10.
A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction. 相似文献
11.
通过时效曲线测量和电镜观察,研究了时效前的预变形对一种Al-Li合金时效行为和显微组织的影响。实验结果表明,时效前的少量预变形加速了时效析出过程,促进了S′(Al_2CuMg)相的析出。此外,经过预变形的试样时效后具有较大的时效硬化量,同时具有较窄的晶界无沉淀带。讨论了晶界无沉淀带形成的机理,分析了预变形和时效组织之间的关系。 相似文献
12.
少量Cu对喷射沉积Al-Li合金显微组织与性能的影响 总被引:1,自引:0,他引:1
用喷射沉积方法制备了Al-Li合金及其含0.5%Cu的改型合金,进行了挤压和时效处理,测定了不同状态下这两种合金的显微组织和室温拉伸性能。结果表明,喷射沉积状态的Al-3.8Li-1.0Mg-0.4Ge-0.2Zr合金具有等轴细晶组织,析出Al4Li9和δ AlLi相,时效后析出大量δ' AlLi相;添加0.5%Cu使屈服强度提高30~48MPa,拉伸强度提高44MPa,性能提高的原因是Cu的固溶强化和Li在基体固溶度减少导致δ'相含量增加。 相似文献
13.
以铁氧体复合吸波材料为例,概述了吸波材料发展趋势;介绍了两种新型隐身材料(碳纳米管复合吸波材料和左手材料)的发展现状,并对我国吸波材料的发展提出一些建议. 相似文献
14.
张卫东%冯小云%孟秀兰 《宇航材料工艺》2000,30(3):1-4,10
简单回顾了从二次世界大战至今几十年间,国外隐身材料的发展历程;系统综述了国外在陶瓷材料,导电高分子材料,晶须材料,纳米材料,手征材料等新型隐身材料研究方面所取得的进展,从耐高温隐身材料,智能隐身材料,等离子体隐身三个方面入手,重点介绍了国外近年来在隐身材料领域的最新进展;并且指出了隐身技术未来的发展方向。 相似文献
15.
Guangda SUN Weizhao SUN Li ZHOU Sanfeng LUO Zili ZHANG Debo LIU Huiqiang WU 《中国航空学报》2024,(1):345-361
The 8 mm-thick 2195 Al-Li alloy joints were achieved by Friction Stir Welding(FSW).The microstructural evolution, temperature-dependent mechanical properties, and fracture properties were studied. The T1, δ’/β’and θ’precipitates were observed in the Base Metal(BM) and the Heat Affected Zone(HAZ). Most of the precipitates, except for re-precipitated δ’/β’phases, were dissolved in the Nugget Zone(NZ). The tensile specimens that failed at cryogenic temperatures(–196.C) had the maximum Ultimate Tens... 相似文献
16.
超声振动载荷下合金的疲劳裂纹扩展性能研究 总被引:3,自引:0,他引:3
本文应用超声共振试验技术研究了4种工程常用合金(Astroloy, 17-4PH, Ti-6Al-4V, Al-Li8090)在超声振动载荷(f=20kHz, R=-1)下的疲劳裂纹扩展性能, 并与常规疲劳载荷(f≤50Hz, R=0.7)下材料的有关性能做了对比分析。对超声疲劳载荷下材料损伤及裂纹扩展机理的特点做了研究, 给出了这种特定载荷形式下应力强度因子的计算方法。研究结果表明, 超声疲劳载荷下各种合金的裂纹扩展性能与常规疲劳试验中确定的有效应力强度因子△Keff类同。 相似文献
17.
19.
20.
Al-Li合金中超点阵相的研究 总被引:1,自引:0,他引:1
用常规透射电子显微术(TEM)、高分辨电子显微术(HREM)、点阵象模拟和动力学衍身模拟技术研究了Al-2.54Li-1.24Cu-1.01Mg-0.13Zr(AA8090)中的超点阵相。结果证实了Al_3Li和Al_3Zr相的晶体结构符合Silcock提出的模型,并发现,Al-Li-Cu-Mg-Zr合金中同时存在Al_3Zr、Al_3Zr相和Al_3Li/Al_3Zr共生体。在纯二元Al-Li合金中,Al_3Li相主要在淬火过程中调幅分解;在多元合金中,Al_3Li相以第二相质点为核心的析出也是一种重要的形式。 相似文献