A New Resonant Mode Amplifier Produces Clean AC Power

A new resonant mode power amplifier design is described which has a number of advantages over the power amplifiers available today. In particular, it has low or no EMI because of the nature of its operation. The new amplifier design is based upon a resonant mode dc-dc converter used in a push-pull configuration. All the advantages of the resonant mode power converters, such as high efficiency, small size and weight, excellent dynamic performance, low or no EMI (compared to PWM switch mode power converter), etc., are present in this new design.     

Design and technology of compact high-power converters

New material technologies such as Silicon Carbide (SiC) are promising in the development of compact high-power converters for next-generation power electronics applications. This paper presents an optimized converter design approach that takes into consideration non-linear interactions among various converter components, source and load. It is shown that with the development of high-temperature, high-power SiC power module technology, magnetic components and capacitors become important technology challenges, and cannot be ignored. A 50% improvement in power density is calculated for a 100 V-2 kV, 7 kW SiC DC-DC power converter operating at 150°C compared to a silicon power converter. The SiC power converter can be operated at junction temperatures in excess of 300°C (as compared to 150°C for a silicon power converter) with reasonable efficiency that potentially leads to a significant reduction in thermal management     

Analysis and Design of Series Resonant Converter by State-Plane Diagram

Analysis based on the state-plane diagram is given for series resonant converters operating in the frequency range 0.5 ? fs/fo ? 1.0. When the voltages and currents in the converter are normalized, design parameters take on special geometric meanings in the normalized state diagram. Examples of converter design using graphical methods are given for the cases of ? and ? control. Control characteristics of the converter operating in the continuous conduction mode are derived. The concept of the energy reflection coefficient is introduced as a measure of power transfer efficiency in the converter design.     

Algorithms for Power Converter Design Optimization

A practical optimization approach for power converters is established which allows conception of a design to meet all powercircuit performance requirements and concurrently to optimize a defined quantity such as weight or losses. In addition to facilitating a cost effective design, the computer-aided approach provides a means to readily assess a) the weight-efficiency tradeoff, b) impacts of converter requirements and component characteristics on a given design, and c) optimum power-system configurations. The following two popular algorithms for nonlinearly constrained optimization are utilized to design the power converter: 1) the sequential unconstrained minimization technique, SUMT Version 4; 2) the ALAG penalty function technique, ALAG5. These algorithms are compared, and suggestions are made for improving the efficiency of the optimization algorithms for power converter design.     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

基于车载用燃料电池直流变换器的研究及应用

通过对燃料电池的特性及碳化硅(SiC)功率器件分析,研究适合车载用的高效率和高可靠性的燃料电池专用Boost变换器。通过对变换器的拓扑结构的优化、效率的提升及控制方法改进等方面研究,设计了一款电压变换比大的适合燃料电池运行要求的高效及可靠运行的变换器。试验样机测试证明,该变换器具有良好的动态和稳态控制特性、效率高,可实现燃料电池的稳定输出运行,有效保护了燃料电池,进一步延长了燃料电池寿命。     

Novel single-switch converter with power factor correction

A new single-stage single-switch power factor correction converter with output electrical isolation is presented. The configuration of this converter is achieved by combining a flyback circuit and a forward circuit in one power stage. The principle of operation and steady-state analysis of the proposed topology is given. Based on its steady-state operation constraints, a design procedure along with a specific design example is reported. To verify the theoretical analysis of the proposed converter, a design example is given with its PSPICE simulation and experimental results     

AMTEC cells challenge energy converters

Sodium-base alkali-metal-thermal-to-electric conversion (AMTEC) cells have been receiving attention. Recently they were selected for the next generation deep-space missions, which need a converter that makes electricity from radioisotope heat. The AMTEC cell, being an electrochemical converter of heat to electricity, has no moving parts and is not limited to Carnot-cycle efficiency. However, its heat source and sink have to be near each other, so the challenge in AMTEC design is to minimize thermal losses and maximize electricity production. This required clever thermal designs. By 1991, high-temperature materials and computer modeling became available. The important AMTEC application was generating power from radioisotope heat in deep space missions. These spacecraft power needs had previously been supplied by inefficient thermoelectric converters     

Evaluation of active hybrid fuel cell/battery power sources

Hybrid fuel cell/battery power sources have potentially widespread uses in applications wherein the power demand is impulsive rather than constant. Interposing a dc/dc converter between a fuel cell and a battery can create two configurations of actively controlled hybrid fuel cell/battery power sources. Those two configurations are compared using both theory and experiment with special attention to the peak power enhancement, and power losses in the converter. Both of the defined configurations were built, using a 35 W polymer electrolyte membrane (PEM) fuel cell, an 8-cell lithium-ion battery pack, and a high-efficiency power converter. Both two configurations yielded a peak power output of 135 W, about 4 times as high as the fuel cell alone could supply, with only a slight (13%) increase of weight. The converter losses were quantitatively analyzed. Which of the two configurations yields a smaller loss depends on the load power demand characteristics including peak power and load duty ratio. The study results provide guidance for the design of hybrid sources according to the particular load power requirements.     

节能高效数字化兆瓦级风电变流器试验系统

针对现有风电变流器试验系统能量损耗高、试验效率低的问题,提出了一种基于环形功率回馈的试验方法。重点阐述了试验系统的基本原理与结构,并搭建了变流器试验软硬件平台,实现了对变流器各特性参数的自动测试要求。对兆瓦级风电变流器进行了相应的试验,试验结果表明:该系统试验效率优,而且系统操作方便,安全可靠,可实现变流器试验系统的高效节能与数字化。     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

Control design and closed-loop analysis of a switched-capacitorDC-to-DC converter

The theoretical and practical details involved in the control design and closed-loop analysis of a step-down switched-capacitor (SC) DC-to-DC converter are presented. The state-space averaging technique is applied to extract the small-signal dynamics of the power stage, and a graphical loop gain method is used to design the feedback compensation and analyze the closed-loop performance of an SC converter. The results of the control design and closed-loop analysis are substantiated by experiments using a prototype SC converter     

High-performance EHA controls using an interior permanent magnetmotor

A controller for a high-performance electrohydrostatic actuator (EHA) using an interior permanent magnet (IPM) synchronous motor to produce servo motion is described. The buried-magnet design of the IPM motor yields desired characteristics such as high efficiency, robust rotor construction, and wide operating speed range. Power converter size is minimized by using insulated-gate bipolar transistor (IGBT) power switches combined with high-voltage integrated circuit (HVIC) gate drivers in phase-leg power modules. Experimental results for the demonstrator motor-controller hardware rated at 12 hp (continuous) are presented confirming the IPM motor drive's performance     

超大功率电推进电源处理单元关键技术研究

针对深空探测等空间任务对超大功率(10kW~100kW范围)电推进系统的需求,通过对国内外超大功率电推进技术的调研,提出了一种50kW超大功率霍尔电推进系统电源处理单元（Power Processing Unit,PPU）设计方案,重点对核心的阳极电源关键技术进行研究,提出了四管Buck-Boost变换器和三相LLC谐振变换器级联的设计方案,为我国超大功率PPU的发展提供了技术参考。     

Computer Simulations of Optimum Boost and Buck-Boost Converters

The development of mathematical models suitable for minimum weight boost and buck-boost converter designs are presented. The facility of an augumented Lagrangian (ALAG) multiplier-based nonlinear programming technique is demonstrated for minimum weight design optimizations of boost and buck-boost power converters. ALAG-based computer simulation results for those two minimum weight designs are discussed. Certain important features of ALAG are presented in the framework of a comprehensive design example for boost and buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.     

Voltage-based maximum power point tracking control of PV system

Photovoltaic (PV) generators exhibit nonlinear v-i characteristics and maximum power (MP) points that vary with solar insulation. An intermediate converter can therefore increase efficiency by matching the PV system to the load and by operating the solar cell arrays (SCAs) at their maximum power point. An MP point tracking algorithm is developed using only SCA voltage information thus leading to current sensorless tracking control. The inadequacy of a boost converter for array voltage based MP point control is experimentally verified and an improved converter system is proposed. The proposed converter system results in low ripple content, which improves the array performance and hence a lower value of capacitance is sufficient on the solar array side. Simplified mathematical expressions for a PV source are derived. A signal flow graph is employed for modeling the converter system. Current sensorless peak power tracking effectiveness is demonstrated through simulation results. Experimental results are presented to validate the proposed method     

Modeling of a new ZVS bi-directional dc-dc converter

A dual half-bridge (DHB) bidirectional dc-dc converter is a new proposed topology that has the advantages of decreased number of devices, soft-switching implementation, low cost, and high efficiency. Typical applications of this converter are the auxiliary power supply in fuel cell vehicles and battery charging and discharging systems where the power density, cost, weight, and reliability are critical factors. A switching-frequency-dependent state-space averaged model of the converter is developed here for either direction of power flow. This averaged model can be used to derive the steady-state characteristics and small signal dynamics of the proposed topology. It also provides a fast simulation tool to investigate the transient response of the converter. The simulated waveforms of the mathematical model are compared with the detailed circuit simulation to verify the accuracy of the modeling.     

Comparison of half-bridge off-line, ZCS-QRC and ZVS-MRC

The performance of the half-bridge (HB) zero-current-switched (ZCS) quasi-resonant converter (QRC) and zero-voltage-switched (ZVS) multiresonant converter (MRC) is compared with respect to their efficiency, input voltage range, semiconductor stresses, power density, and reliability. The efficiency of the HB ZVS-MRC at a given nominal input is shown to be highly dependent on the range of the input voltage, and it suffers when the converter has to be designed to cover a wide range. However, this is not the case for the HB ZCS-QRC. Experimental versions of the HB ZCS-QRC and HB ZVS-MRC were designed for the input voltage range from 150 to 350 V and a maximum output power of 100 W, under the same constraints, to facilitate their comparison     

直升机旋翼/动力传动链扭振分析与试验

本文以某型机为例，对旋翼／尾桨／动力传动系统扭振特性进行了综合建模分析与试验，试验表明整个传动链的扭振固有频率和振型计算结果正确，为消除动力传动链扭振与发动机燃油调节系统耦合动不稳定性提供了可靠的设计依据，提出的传动链扭振与发动机燃调系统耦合稳定性检查试验方法，首次在该型机的研制中取得成功。