Signal-to-Noise Ratio Calculations in Pulse and Pulse Doppler Radars

In low pulse-repetition frequency (PRF) pulse radars, signal-to-noise ratio (SNR) is usually calculated on a per pulse basis and this value is then multiplied by the number of pulses integrated to obtain the SNR for a given duration of target illumination. In high PRF pulse Doppler radars, SNR is usually calculated by using the centerline power of the transmitted signal spectrum as the target return power because the centerline is kept in the receiver and returns of the PRF lines are notched out [1]. We show here that both methods of SNR calculations are entirely equivalent for matched transmit-receive radar systems.     

Medium PRF set selection using evolutionary algorithms

This paper presents a new and novel method of selecting multiple pulse repetition frequency (PRF) sets for use in medium PRF pulsed-Doppler radars. Evolutionary algorithms are used to minimise the blind areas in the range/Doppler space. The evolutionary algorithm allows optimal solutions to be generated quickly, far faster than with exhaustive searches, and is fully automatic, unlike existing techniques. The evolved solutions compare very favorably against the results of both an exhaustive search and existing published PRF set selection methods. This evolutionary approach to generation of PRF sets is a major advance in medium PRF radar design.     

Medium PRF radar PRF selection using evolutionary algorithms

Evolutionary algorithms are applied to the optimization of pulse repetition frequency (PRF), for both eight-and nine PRFs, in medium PRF radar while considering the detailed effects of sidelobe clutter and many other technical factors. The algorithm presented also ensures that all the solutions produced are fully decodable and have no blind velocities. The evolutionary algorithm was able to identify near-optimum PRF sets for a realistic radar system with only a modest computational effort.     

A Systematic Approach to Blind-Speed Elimination

In radars that achieve a high subclutter visibility by coherent processing over several pulses, a serious problem appears in the form of blind Dopplers, or ?speeds,? at which target detection is impossible. Of the possible methods of eliminating these blind speeds, the most basic one that is employed when the performance requirements are high involves the use of several PRF's. These PRF's are chosen so that coverage is obtained at any Doppler with at least one PRF. The problem faced by the radar designer is to select the set of PRF's and the pulse numbers for each PRF so that the search frame time is minimized. This paper evolves a systematic method for the design of the blind-speed elimination scheme. A formalized approach is offered that shows the possible combinations of wavelength, PRF, and pulse number and the tradeoffs involved, without introducing the confusion ordinarily associated with multiparameter choices.     

Properties of Staggered PRF Radar Spectral Components

Expressions for moving target indicator (MTI) improvement factor limitation due to pulse repetition frequency (PRF) staggering and loss of target detectability for various values of Doppler frequency in the passband are presented. It is also shown that the product of variance of stagger periods and clutter variance is an important parameter determining the performance of a staggered PRF MTI radar.     

A Generalized Clutter Computation Procedure for Airborne Pulse Doppler Radars

A general procedure for analyzing ground clutter effects in airborne pulse Doppler radars is described. The quantity computed is the expected clutter power at the output of any specified range gate/ Doppler filter processing cell. The procedure has been computerized and is quite general with respect to antenna gain pattern, clutter cross section variation, PRF, pulse and range gate shapes, and the various receiver processing functions. It is applicable only to distributed ground clutter and linear processing, and excludes the dynamic effects of continuous antenna scanning. To exemplify the use of the procedure, two studies conducted for a postulated high PRF radar are described, and the results are presented.     

Characterizing radar emissions using a robust countermeasurereceiver

The author presents a high-sensitivity signal processing approach for detecting and estimating the angle of arrival (AOA), frequency and pulse repetition frequency (PRF) of multiple radar emitters using broadband interferometers. Two time series are generated using information embedded in the sampled cross correlation of the signals obtained from three antenna elements (i.e. two base legs). The phase and amplitude of a complex Fourier transform of these two time series with respect to the sampling clock are used to estimate the AOA and PRF of pulsed emitters     

弹载合成孔径雷达自适应重频分析与设计

弹载合成孔径雷达(Synthetic Aperture Radar,SAR)的目标距离、视线角由于高速逼近目标而快速变化,这导致传统的固定脉冲重复频率(Pulse Repetition Frequency,PRF)(简称重频)波形难以兼顾弹载SAR雷达在成像各方面的约束条件,故需要根据当前弹体运动和弹目关系变化情况实时计算重频。详细分析了影响重频选择的各项因素,包括避免距离模糊、方位模糊、高度杂波、发射遮挡影响及SAR成像分辨率、系统相参性要求等影响因素,并设计了自适应重频计算的工作流程。某SAR雷达系统实验表明,该设计能够在实际飞行弹道条件下根据实际弹目关系自适应调整脉冲重复频率,从而更好地实现SAR雷达系统的工作性能,有效解决了固定重频波形不能适应弹载SAR工作条件的难题。     

Mitigating Range Ambiguity in High PRF Radar using Inter-Pulse Binary Coding

The paper proposes a way to increase the energy within a coherent processing interval (CPI) using more pulses instead of longer pulses. Long coded pulses result in masking targets at close range and poor Doppler tolerance. Increasing the number of pulses implies high pulse repetition frequency (PRF), which suffers from range ambiguity and target folding. These drawbacks of a high PRF can be mitigated by inter-pulse coding. The approach suggested here should be attractive for close and mid range applications of radar, ground penetrating radar, ultrasound imaging, and more.     

Performance comparison of PRF schedules for medium PRF radar

Previous work has shown how evolutionary algorithms (EAs) are an effective tool in optimising the selection of pulse repetition frequency (PRF) values of medium PRF schedules in an airborne fire control radar (FCR) application requiring target data in three PRFs. The optimisation is driven by the requirement to minimise range/Doppler blindness whilst maintaining full decodability. In this paper we detail work in which the optimisation process is applied to design novel short medium PRF schedules requiring target data in just two PRFs. The paper reports on the testing of a variety of near-optimum schedules to compare their blindness, decoding, and ghosting performances. The results show that in many situations, the 2 of N schedules are a practical alternative to conventional 3 of N processing.     

Ambiguity Functions for Quadratic Phase-Coded Pulse Trains

The matched filter ambiguity function is presented for a burst waveform composed of repeated subbursts, each one of which consists of N pulses in which the phase is varied quadratically from pulse to pulse. The resulting ambiguity function exhibits small residual ambiguities along the delay axis separated by the reciprocal of the pulse repetition frequency (PRF). A cross-ambiguity function is derived which reduces these ambiguities to zero amplitude. A third cross-ambiguity function is presented for a receiver matched to a generalized Hamming weighted repeated quadratic burst. The location in the delay/Doppler plane of the waveform ambiguities for these waveforms is compared with that of an uncoded pulse burst.     

相控阵主动雷达导引头波形策略

针对高脉冲重复频率脉冲多普勒(HPRF-PD)体制的相控阵主动雷达导引头中存在的距离遮挡问题,设计了一种新的波形选择策略。首先,利用提出的脉冲重复频率(PRF)波形选择策略,离线计算得到距离对应PRF的波形查找表。然后,通过叉积自动频率控制环路滤波(CPAFCLF)算法预估下个相参处理间隔(CPI)导引头与目标间的径向相对速度,并联合提出的基于Sage-Husa带有速度预测的自适应"当前"统计模型(SH-ACSMVP)算法得到的距离跟踪值,获得下个CPI的距离预测值。在跟踪机动目标场景中,相比于"当前"统计(CS)模型跟踪算法及基于"当前"统计模型的自适应无迹卡尔曼滤波(CAUKF)算法,本文算法得到的距离预测误差更小,误差收敛速度更快。根据此距离预测值从波形查找表中选择波形发射,作为下个CPI的发射波形,实现后续跟踪阶段的抗距离遮挡,提高目标跟踪性能。仿真结果表明了本文所设计波形选择策略的正确性及有效性。     

Synthetic Aperture Processing with Limited Storage and Presumming

The number of transmitted pulses associated with the Doppler histories of a side-looking radar may greatly exceed the desired azimuth compression ratio of the system. This discrepancy is taxing if the storage required for the azimuth processing is provided by cores, magnetic drums, and the like. Thus, as a practical matter, one considers presumming of the data prior to correlation in an attempt to achieve the desired performance with a minimum amount of digital storage. In this paper, the optimum (in terms of resolution) presummer is derived, along with the optimum apportionment of the available storage capacity between the presumming and correlation operations. Under the condition (or generally pessimistic approximation) that the illumination pattern of the antenna uniformly illuminates a Doppler bandwidth equal to the PRF of the radar, the optimum presumming coefficients are the first Np Fourier coefficients of a function which is one of the Doppler bandwidth to be correlated and zero on the remainder of the PRF bandwidth, where Np is the number of transmitted radar pulses over which presumming is provided. Increasing Np reduces the degradation due to presumming, but may leave inadequate storage for correlation. Hence, we optimize the apportionment between the two operations and present the obtainable resolution as a function of total storage and the number of transmitted pulses in the received Doppler history.     

The Effect of a Pulsed Interference Signal on an Adaptive Array

The performance of a least mean square (LMS) adaptive array in the presence of a pulsed interference signal is examined. It is shown that a pulsed interference signal has two effects. First, it causes the array to modulate the desired signal envelope (but not its phase). Second, it causes the array output signal-to-interferenceplus-noise ratio (SINR) to vary with time. The desired signal modulation is evaluated as a function of signal arrival angles, powers and interference pulse-repetition frequency (PRF) and pulsewidth. It is shown that the signal modulation is small except when the interference arrives close to the desired signal. To evaluate the effect of the time-varying SINR, it is assumed that the array is used in a differential phase-shift keyed (DPSK) communication system. It is shown that the SINR variation causes a noticeable but not disastrous increase in the bit error probability.     

Velocity estimation of fast moving targets using a single SAR sensor

A new methodology is presented to retrieve slant-range velocity estimates of moving targets inducing Doppler-shifts beyond the Nyquist limit determined by the pulse repetition frequency (PRF). The proposed approach exploits the linear dependence (not subject to PRF limitations) of the Doppler-shift with respect to the slant-range velocity, at each wavelength. Basically, we propose an algorithm to compute the skew of the two-dimensional spectral signature of a moving target. Distinctive features of this algorithm are its ability to cope with strong range migration and its efficiency from the computational point of view. By combining the developed scheme to retrieve the slant-range velocity with a methodology proposed earlier to estimate the velocity vector magnitude, the full velocity vector is unambiguously retrieved without increasing the mission PRF. The method gives effective results even when the returned echoes of the moving targets and the static ground overlap completely, provided that the moving targets signatures are digitally spotlighted and the signal-to-clutter ratio (SCR) is, roughly, greater than 14 dB. The effectiveness of the method is illustrated with simulated and real data. As an example, slant-range velocities of moving objects with velocities between 6 and 12 times the Nyquist velocity are estimated with accuracy better than 3%.     

Dwelltime Minimization for Radar Target Detection in the Clear

Consider the design of a minimum dwelltime set of coherent, range-unambiguous pulse bursts that will provide a specified target detection performance in a clutter-free ("clear") range interval [Rmin,Rmax]. Practical procedures are presented here for finding these optimal waveform sets versus Rmax/Rmin, subject to a peak transmit power constraint. It is always possible to design a multiple-PRF clear mode that achieves the same effective use of energy as a single-PRF waveform with a 33 percent duty ratio. Slightly higher effective duty ratios can be achieved if the radar is capable of transmitting and processing two interleaved pulse bursts at the same PRF.     

结合视线方向运动补偿的滑动聚束SAR子孔径成像算法

滑动聚束合成孔径雷达(SAR)是一种新兴的成像模式,既可以提高方位向分辨率又能够扩展成像范围。其数据处理时需要考虑两个关键问题:一是系统脉冲重复频率(PRF)不足,方位向信号发生混叠;二是合成孔径长度的增加使运动误差的影响更为突出,运动补偿(MOCO)精度要求提高。基于子孔径技术,提出了一种改进的高分辨率成像算法。划分子孔径克服了PRF不足的问题;子孔径数据处理采用结合视线(LOS)方向运动补偿的Omega-K算法,实现更高精度的运动补偿,提高了聚焦质量。最终的方位向分辨率达到0.1 m,具有实际工程应用价值。点目标仿真和实测数据处理验证了算法的有效性。     

Doppler ambiguity resolution using multiple PRF

An algorithm for velocity ambiguity resolution in coherent pulsed Doppler radar using multiple pulse repetition frequencies (PRF) is presented. It relies on the choice of particular values for the PRFs. The folded frequency of the target signal is obtained by averaging the folded frequency estimates for each PRF, and a quasi maximum likelihood criterion is maximized for ambiguity order estimation. The fast implementation of this nonambiguous estimation procedure is based on the fast Fourier transform (FFT), The proposed waveform allows full exploitation of any (even) number of PRFs, which appears to be important for estimation improvement. The effects of the waveform parameters and the folded frequency estimation variance on the performance of the ambiguity order estimation procedure are evaluated theoretically and through computer simulations. Mean square error (MSE) curves are given to assess the Doppler frequency estimation accuracy. Finally, the new method is compared with a classical technique and the implementation of the algorithm in a clutter environment is addressed.     

高信噪比、高分辨宽测绘带成像

针对传统高分辨和宽测绘带以及高信噪比和宽测绘带之间的矛盾,提出一种基于脉内扫描面阵合成孔径雷达(SAR)系统的二维空域联合处理算法实现高信噪比、高分辨宽测绘带成像。文中首先建立脉内扫描面阵SAR系统模型,该系统采用低脉冲重复频率(PRF)获得宽测绘带信息,同时利用脉内扫描方式获得高信噪比的回波信号。对于低PRF采样宽多普勒谱(对应方位高分辨)引起的多普勒模糊以及脉内扫描引起的距离模糊,提出一种二维空域联合处理算法解距离和多普勒模糊,并且详细地分析了地形高度变化对解模糊算法的影响。最后,通过仿真实验验证了本文算法的有效性。