主燃孔轴向位置对低压点火性能的影响

对回流燃烧室设计了两种主燃孔结构(交错射流和对齐射流),在不同压力条件下对不同主燃孔方案的回流燃烧室的点火性能进行了试验研究.试验结果表明:随着回流燃烧室进口空气压力的降低,点火边界的油气比先减小后升高,而对齐主燃孔的火焰筒方案的低压点火性能优于交错主燃孔.结合火焰筒冷态流场数值模拟和试验中观察到的点火现象进行对比分析,对齐主燃孔方案存在更大范围的回流区,其火焰筒头部参考速度较低.此方案有利于减弱火焰核心的淬熄概率,同时增强头部火焰燃烧的稳定性,从而改善了回流燃烧室的点火性能.      

火焰筒压力损失对点火特性的影响

以3.0%火焰筒压力损失火焰筒作为基准,分别设计了2.5%和2.0%火焰筒压力损失的火焰筒,通过试验研究火焰筒压力损失对地面起动点火性能的影响,对火焰筒内部流场进行数值模拟.在火焰筒压力降3.0%以内的空气条件下,3种方案贫油点火边界基本一致,低压力损失火焰筒能够在更宽的压力降条件下点燃,2.5%方案的综合点火性能最好.结合数值模拟结果:压力损失降低至2.0%,流场结构与基准方案有较大的区别,对燃烧室的性能开始产生不利影响,2.5%方案与基准方案流场结构较为接近,定量的变化对燃烧室的性能影响是有益的.      

中心分级燃烧室点火性能试验研究

对中心分级燃烧室常温常压和常温低压下的点火性能进行了试验研究。在进口压力分别为0.1,0.035,0.03MPa,进口温度为常温的条件下,试验研究了不同空气压降(0.5%～6%)下的贫油点火油气比,获得了其点火边界曲线。试验结果表明:随着压力降增加,在各种燃烧室进口压力下的贫油点火油气比具有一个最低值;随着进口压力减小,这个最低值所对应的压降不断降低,同时贫油点火油气比升高。通过分析进口空气条件、燃烧室参考速度和燃油SMD对点火性能的影响,得到了其点火模型。     

全环涡轮级间燃烧室性能试验

以涡轮级间燃烧室(ITB)应用于涡轴发动机为研究平台,根据ITB的应用环境,采用凹腔驻涡燃烧室作为涡轮级间燃烧室,设计加工了全环凹腔驻涡燃烧室试验件,并进行了性能试验研究.试验结果表明:该燃烧室的贫油点火边界余气系数为10.2,降低驻涡凹腔体内外压差有利于点火;与常规燃烧室相比,燃烧室的燃烧效率偏低,但燃烧效率随进口温度的升高逐步加大;燃烧室的总压恢复系数较小,进口温度对燃烧室的总压恢复系数影响不大;燃烧室出口温度场分布较好,出口温度分布系数(OTDF)随进口温度的升高而减小;随着进口温度的提高,火焰筒壁温会局部偏高,火焰筒的冷却设计需优化改进.      

不同台阶高度对中心分级燃烧室点火熄火性能的影响

设计了一种贫油燃烧中心分级燃烧室,采用单头部矩形试验件,试验研究了3种不同台阶高度对点火熄火性能的影响.试验中只有预燃级喷嘴供油工作,在常温常压、常温低压条件下进行了贫油点火试验,在常温常压、加温常压下进行了贫油熄火试验.结果表明:台阶高度越大,贫油点火边界越宽,同时贫油熄火边界越宽;进口温度的升高有助于改善贫油熄火性能,并缩小3种方案贫油熄火油气比的差距,在320~570K的进口温度范围内,贫油熄火油气比的最大差距由40%减小到13%;3种方案都具有较好的常温负压点火性能,且在0.5%~1.5%的火焰筒进出口总压降下,贫油点火油气比差异不大,最大相差不超过10%.     

超音速燃烧室碳氢燃料点火实验研究

模拟飞行Ma =3 5的超燃冲压发动机的燃烧室进口条件 ,采用氢为先锋火焰 ,在氢氧燃烧加热脉冲风洞上 ,对超燃燃烧室煤油燃料的点火和火焰稳定进行了实验研究 ,实现了煤油的点火和火焰稳定。实验测量了燃烧室壁面压力分布 ,并拍摄了燃烧火焰紫外光图像。实验表明 ,在燃烧室进口温度较低 (小于 90 0K)的条件下 ,在超燃燃烧室中实现煤油自燃十分困难 ,采用氢为先锋火焰实现煤油的点火是较为有效的途径之一。     

喷嘴匹配方案及火焰筒开孔对燃烧室性能影响的试验研究

基于航空发动机主燃烧室扇形试验,针对点火喷嘴特性以及火焰筒大孔射流的改变对主燃烧室性能的改善情况进行了研究。试验中进行了点火用喷嘴匹配方案对燃烧室熄火性能,以及火焰筒大孔面积变化对燃烧室贫油熄火、燃烧效率和出口温度场性能影响的研究。研究结果表明：在供油系统设计中采用放大型点火喷嘴可改善主燃烧室贫油熄火性能;增大火焰筒主燃孔的面积可提高燃烧室的燃烧效率,改善出口温度场分布,而贫油熄火特性将变差;增大掺混孔的面积可提高燃烧室的燃烧效率,改善出口温度场分布,拓宽燃烧室的熄火动界．     

Experimental Investigation of Hydrocarbon-fuel Ignition in Scramjet Combustor

模拟飞行Ma=3．5的超燃冲压发动机的燃烧室进口条件，采用氢为先锋火焰，在氢氧燃烧加热脉冲风洞上，对超燃燃烧室煤油燃料的点火和火焰稳定进行了实验研究，实现了煤油的点火和火焰稳定。实验测量了燃烧室壁面压力分布，并拍摄了燃烧火焰紫外光图像。实验表明，在燃烧室进口温度较低(小于900K)的条件下，在超燃燃烧室中实现煤油自燃十分困难，采用氢为先锋火焰实现煤油的点火是较为有效的途径之一。     

局部富油供油扩展燃烧室贫油点火熄火边界研究

介绍了燃烧室主燃区设计中熄火特性与综合性能间的折衷考虑,设计了火焰筒头部均匀供油和局部富油供油方案,并在全环试验燃烧室上进行了两种方案对燃烧室贫油点火熄火边界影响的对比试验,分析和总结了火焰筒头部局部富油设计方案的点火熄火规律。结果表明:局部富油设计可显著扩展燃烧室贫油点火熄火边界。      

微型燃气轮机乙醇燃烧室点火与熄火试验

对应用于微型燃气轮机上的可再生生物质燃料乙醇燃烧室开展了试验研究,包括4种不同的供油方式,获得了常温常压进口条件下乙醇燃烧室的点火与熄火特性.研究结果表明:常温常压下采用旋流器的乙醇燃烧室的贫油点火和贫油熄火当量比的值均随空气流量的增加而减小,其点火与熄火性能优于预蒸发预混管燃烧室.      

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.