基于模糊控制的永磁同步电机直接转矩控制

设计了基于模糊控制的永磁同步电机(PMSM)直接转矩控制(DTC)系统,采用模糊控制器取代了传统DTC系统中的磁链和转矩滞环比较器及开关表。仿真结果表明:模糊控制PMSM DTC系统运行良好,可实现四象限运行,与传统开关表相比,可有效减小转矩脉动和平均开关频率。研究了转矩误差论域和零电压矢量对模糊控制性能的影响,并基于转矩角对电压矢量作用的影响规律,提出了考虑转矩角的PMSM模糊直接转矩控制。仿真结果表明:在转矩角较大时,考虑转矩角的PMSM模糊DTC系统可有效减小转矩和磁链脉动,改善控制性能。     

霍尔推进系统扭矩特性分析及应用设计

为降低霍尔推进系统产生的扭矩长期作用于航天器对姿态控制造成的干扰,对其扭矩特性进行分析和优化设计,通过对扭矩的产生机理进行模型化分析,得到了放电参数对扭矩大小及方向的影响关系。分析表明,1kW～5kW功率级霍尔推力器工作时,会产生量级为10-4N?m的扭矩,通过控制励磁电流方向可改变扭矩方向。针对典型的全电推进飞行任务,通过提出霍尔推进系统扭矩主动控制设计,实现了对系统产生的扭矩进行相互抵消或者叠加利用,降低了系统的应用风险。     

采用瞬时转矩控制策略的异步发电系统的容错研究

在六开关三相异步发电系统中增加较少的硬件,可实现对常见故障的容错,容错后系统重构为四开关三相运行系统。研究了容错型四开关三相系统中电压矢量的特点及其对磁链和转矩的调节作用,提出了四开关三相系统瞬时转矩控制中磁链和转矩的控制方案。对四开关三相异步发电系统的几个关键问题进行了研究,针对电容电压漂移问题,提出了修正转矩给定的有效方法。最后给出了仿真与实验结果。     

基于二次调节原理的力矩负载模拟器中压力波动的补偿

 基于静液二次调节原理的力矩负载模拟器具有能够连续高速旋转和无多余力矩的特点。在恒压网络中,二次元件的力矩输出与其斜盘倾角成正比,即：如果系统压力出现波动,也将导致输出力矩的波动。导致系统压力变化的原因可能是油源压力脉动,但更主要是负载的变化。为了研究压力波动的影响及补偿,建立了基于静液二次调节原理的力矩负载模拟器,给出了仿真参数,并在此基础之上进行了仿真研究。为了提高力矩跟踪精度,提出利用斜盘倾角传感器和系统压力传感器来进行压力补偿,可有效地将系统压力波动对于力矩输出的影响抑制到20%左右。仿真和试验验证了此补偿方法的有效性。     

飞机高升力系统扭力管旋转角度测试方法

在飞机地面模拟试验环境下需要测试高升力系统襟翼扭力管旋转角度.由于扭力管属于系统试验件,在不改变试验环境构型的情况下不可截断或更换安装用于测试扭力管旋转角度的旋转编码器.本文利用同步轮法实现了在不破坏扭力管前提下安装旋转编码器测试扭力管旋转角度,方法简单、可靠,且容易实现,很好的满足了试验大纲要求.     

基于重构系统的永磁交流伺服系统在线转动惯量辨识

为了使伺服系统在负载变动下得到优良的动态响应,提出了一种基于实际电机控制系统输入输出构建的非线性可调重构模型,对实际系统进行重构,并根据收敛之后的重构模型参数,完成电机关键机械参数的准确辨识。其中,全维观测器用来获得电机负载转矩状态观测量,与输入电磁转矩一同作为所构建的自适应机构的输入参数;当可调重构系统的输出与实际系统的输出为无差收敛时,实现对实际系统的重构。仿真和试验验证了该方法的可行性和有效性,能够对模型中预设的不同转动惯量进行准确的辨识。     

基于智能神经元PID的异步电机直接转矩控制

针对异步电机直接转矩控制系统PID转速调节器的适应性、鲁棒性及抗干扰性较差的问题,提出了基于智能神经元PID转速调节器的异步电机直接转矩控制方法。智能神经元PID转速调节器采用2个神经元控制器进行设计,同时实现了控制器参数的在线调整,磁链调节器和转矩调节器分别采用滞环调节器进行设计。仿真结果表明,基于智能神经元PID的异步电机直接转矩控制系统能快速跟踪参考转速变化,具有很强的抗干扰能力、自适应能力和较强的鲁棒性。     

Adaptive Nonlinear Optimal Compensation Control for Electro-hydraulic Load Simulator

 Directing to the strong position coupling problem of electro-hydraulic load simulator (EHLS), this article presents an adap-tive nonlinear optimal compensation control strategy based on two estimated nonlinear parameters, viz. the flow gain coeffi-cient of servo valve and total factors of flow-pressure coefficient. Taking trace error of torque control system to zero as control object, this article designs the adaptive nonlinear optimal compensation control strategy, which regards torque control output of closed-loop controller converging to zero as the control target, to optimize torque tracking performance. Electro-hydraulic load simulator is a typical case of the torque system which is strongly coupled with a hydraulic positioning system. This article firstly builds and analyzes the mathematical models of hydraulic torque and positioning system, then designs an adaptive nonlinear optimal compensation controller, proves the validity of parameters estimation, and shows the comparison data among three control structures with various typical operating conditions, including proportion-integral-derivative (PID) controller only, the velocity synchronizing controller plus PID controller and the proposed adaptive nonlinear optimal compensation controller plus PID controller. Experimental results show that systems’ nonlinear parameters are estimated exactly using the proposed method, and the trace accuracy of the torque system is greatly enhanced by adaptive nonlinear optimal compensation control, and the torque servo system capability against sudden disturbance can be greatly improved.     

永磁有限转角力矩电机的仿真与实验

随着多电飞机的快速发展及成附件轻小化、高效能的迫切需求,有限转角力矩电机(Limited Angle Torque Motor,LATM)在飞机引气系统中的应用日益迫切。一方面,有限转角力矩电机可以显著简化高温引气控制阀结构、减小体积;另一方面,可以基于系统需求实现引气压力和温度按需调节,减少燃油代偿损失。针对高温有限转角力矩电机工作特性不易预测的难题,建立了其数学模型、仿真模型,并通过实物试验验证了仿真模型的准确性。研究结果为有限转角力矩电机特性研究提供了参考依据。     

冗余飞轮构型下力矩分配策略设计与分析

 主要研究了航天器姿控系统中冗余飞轮构型的力矩分配问题。在阐明该问题的基础上,首先给出了能量最优的力矩分配策略,并考虑飞轮力矩约束对其进行了限幅处理;接着基于静态最优化理论和飞轮系统性质,对四飞轮和多飞轮情况分别设计了相应的力矩最优分配策略,由于可有效地输出飞轮系的最大力矩,其有重要的工程应用价值;最后研究并对比了几种典型构型下两种分配策略所能输出的力矩包络,表明了所设计方法的有效性。     

Analysis of reaction torque-based control of a redundant free-floating space robot

Owing to the dynamics coupling between a free-floating base and a manipulator,the non-stationary base of a space robot will face the issue of base disturbance due to a manipulator's motion.The reaction torque acted on the satellite base's centroid is an important index to measure the satellite base's disturbance.In this paper,a comprehensive analysis of the reaction torque is made,and a novel way to derive the analytical form of the reaction torque is proposed.In addition,the reaction torque null-space is derived,in which the manipulator's joint motion is dynamically decoupled from the motion of the satellite base,and its novel expression demonstrates the equivalence between the reaction torque null-space and the reaction null-space.Furthermore,the reaction torque acted as an optimization index can be utilized to achieve satellite base disturbance minimization in the generalized Jacobian-based end-effector Cartesian path tracking task.Besides,supposing that the redundant degrees of freedom are abundant to achieve reaction torque-based active control,the reaction torque can be used to realize satellite base attitude control,that is,base attitude adjustment or maintenance.Moreover,because reaction torque-based control is a second-order control scheme,joint torque minimization can be regarded as the optimization task in reaction torque-based active or in-active control.A real-time simulation system of a 7-DOF space robot under Linux/RTAI is developed to verify and test the feasibility and reliability of the proposed ideas.Our extensive empirical results demonstrate that the corresponding analysis about the reaction torque is correct and the proposed methods are feasible.     

永磁容错电机最优转矩控制策略实验

 永磁容错(FTPM)电机不仅具有容错和故障隔离能力,还继承了一般永磁电机功率密度大、转矩脉动小的优点,故在航空用电力作动系统中得到大力发展。最优转矩控制(OTC)算法可以实现电机在正常和故障时(一相断路或短路)输出电磁转矩脉动最小化。本文设计了750 W六相十极FTPM电机最优转矩控制系统平台,提出了两种简单实用的绕组故障诊断方法,对最优转矩控制算法进行了实验研究。实验结果表明,该算法能够实现故障前后转矩转速性能基本不变,且转矩脉动均小于20%,故障时动态响应快。     

电动模拟加载测试系统的设计与实现

针对导弹弹翼尾翼电动模拟加载测试系统，设计系统硬件结构，详细分析加载系统中多余力矩的测试及抑制方法，提出以TMS320LF2407 DSP和以直接转矩控制输出的ACS600伺服驱动器为核心的系统实现方法。对电动加载系统快速性和多余力消除这两个关键性的难点给出解决方案。实验结果表明，系统能精确地模拟弹翼及尾翼在飞行展开过程中的气流阻力，满足加载测试系统的快速性要求。     

Study on the Behavior of Solar Array Deployment with Root Hinge Drive Assembly

In this paper, a method of using a root hinge drive assembly (RHDA) to control the solar array deployment is provided and a multi-DOF mechanism dynamic model of the system is established. In this way, the root hinge torque can be calculated iteratively. Then taking the predicted torque as a reference, a RHDA is designed for a large multiple-stage packaging and deployable solar array system. The control effect of the drive assembly is validated by ground tests. The test results indicate that the solar arrays can be deployed smoothly, and the deployment velocities are restricted by the drive assembly as expected. During the tests, the RHDA output speed and output torque are obtained. In order to examine the impact force when the yoke is lock-up with a hard stop, dynamics simulations are performed according to the actual behavior. The simulation result indicates that the designed RHDA reduces the impact force significantly and improves the lock-up reliability effectively.     

Fault tolerant control with torque limitation based on fault mode for ten-phase permanent magnet synchronous motor

This paper proposes a novel fault tolerant control with torque limitation based on the fault mode for the ten-phase permanent magnet synchronous motor(PMSM) under various open-circuit and short-circuit fault conditions, which includes the optimal torque control and the torque limitation control based on the fault mode. The optimal torque control is adopted to guarantee the ripple-free electromagnetic torque operation for the ten-phase motor system under the post-fault condition. Furthermore, we systematically analyze the load capacity of the ten-phase motor system under different fault modes. And a torque limitation control approach based on the fault mode is proposed, which was not available earlier. This approach is able to ensure the safety operation of the faulted motor system in long operating time without causing the overheat fault. The simulation result confirms that the proposed fault tolerant control for the ten-phase motor system is able to guarantee the ripple-free electromagnetic torque and the safety operation in long operating time under the normal and fault conditions.     

基于四开关三相变频器的永磁同步电机驱动系统转矩脉动优化控制

针对低成本三相四开关变频器构成的永磁同步电机驱动系统存在转矩脉动较大的问题,提出了一种系统转矩脉动优化控制策略。系统中存在的转矩脉动分为低频和高频转矩脉动,对于由直流电容电压波动产生的低频脉动,采用了引入一种基于非正交坐标变换的补偿方案,而对于高频脉动,分析评估了不同调制策略的影响,选择了最优调制策略。此外,线性调制范围设置考虑了系统直流电容电压波动,避免了低频脉动造成的过调制。同时,还设计了电容电压偏移抑制控制以扩大线性调制区范围。试验结果验证了新型控制策略抑制系统转矩脉动的效果明显。     

球柱联合转台轴承摩擦力矩特性

为研究球柱联合转台轴承摩擦力矩特性,建立了轴承的力学模型,采用Newton-Raphson法对模型进行求解。分析了轴承摩擦力矩产生机理,建立了摩擦力矩计算模型,利用试验机对模型进行了试验验证,研究了不同结构参数对轴承摩擦力矩的影响。结果表明:所建立的模型可较好的实现轴承摩擦力矩预测,轴承摩擦力矩与轴向载荷、倾覆力矩和轴承转速呈正相关;减小初始轴向游隙可显著降低轴承摩擦力矩;钢球数量存在一个最优值使轴承摩擦力矩最小;沟曲率半径存在合理区间使轴承综合性能最优;适当减小保持架质量可有效降低轴承摩擦力矩。研究结果为球柱联合转台轴承的优化设计提供了理论依据。     

Adaptive fuzzy terminal sliding mode control for the free-floating space manipulator with free-swinging joint failure

Space manipulator with free-swinging joint failure simultaneously contains kinematic and dynamic coupling relationships, so it belongs to a new underactuated system. To allow the manipulator to carry on tasks, an effective robust underactuated control method for the space manipulator with free-swinging joint failure is studied in this paper. Considering the effect of model uncertainty and joint torque disturbance, a robust underactuated control system based on the Terminal Sliding Mode Controller (TSMC) is designed, but two drawbacks are discussed: (A) Robustness depraves with eliminating chattering. (B) Control parameters are difficult to be determined under unknown uncertainty and disturbance. To improve the TSMC, the adaptive fuzzy controller is introduced to estimate the real effect of unknown uncertainty and disturbance according to deviations of sliding mode and its reaching law. The estimated result is directly compensated into active joints torque. In simulation, the space manipulator with free-swinging joint executes tasks based on the TSMC and the Adaptive Fuzzy Terminal Sliding Mode Controller (AFTSMC) respectively. Same tasks can be finished with smaller joints torque and stronger robustness based on the AFTSMC. Therefore, AFTSMC can serve as an effective robust control method for the space manipulator with free-swinging joint failure under unknown model uncertainty and torque disturbance.     

永磁同步电机变论域模糊直接转矩控制

直接转矩控制(DTC)相比矢量控制转矩响应快,能够很好地适应对转矩响应要求较高的应用场合。但常规DTC存在转矩脉动、磁链脉动大和谐波电流较大的缺点,可能导致更高的定子铜耗,从而降低驱动效率。针对这一问题,以DTC基本原理为出发点,提出一种用磁链和转矩模糊控制器代替传统滞环比较器的控制策略。常规模糊控制器可能会出现模糊规则不足或得不到充分应用的情况,导致模糊控制效果变差,针对这一不足在转矩环加入变论域模糊控制。使用MATLAB/Simulink对变论域模糊DTC系统进行仿真。仿真结果表明:该变论域模糊控制系统能够有效地抑制转矩脉动、磁链脉动和谐波电流。     

旋翼反扭矩系统结构参数对其气动特性的影响分析

针对一种新型的横流风扇式旋翼反扭矩系统,对该系统的流场进行了数值模拟.通过CFD计算,分析了这种新型反扭矩系统的结构参数对其流场的影响,找出该反扭矩系统的最优几何参数,使得这种新型反扭矩系统能够获得更好的性能.