10 Years of LAGEOS-1 and 15 years of LAGEOS-2 spin period determination from SLR data

Satellite Laser Ranging (SLR) stations measure distance to the satellites equipped with Corner Cube Reflectors (CCRs). These range measurements contain information about spin parameters of the spacecraft. In this paper we present results of spin period determination of two passive satellites from SLR data only: 10 years of LAGEOS-1 (10426 values), and 15 years of LAGEOS-2 (15580 values). The measurements have been made by standard 10 Hz SLR systems and the first 2 kHz SLR system from Graz (Austria). The obtained data allowed calculation of the initial spin period of the satellites: 0.61 s for LAGEOS-1 and 0.906 s for LAGEOS-2. Long time series of the spin period values show that the satellite’s slowing down rate is not constant but is oscillating with a period of 846 days for LAGEOS-1 and 578 days for LAGEOS-2. The results presented here definitely prove that the SLR is a very efficient technique able to measure spin period of the geodetic satellites.     

TLE数据误差与基于TLE数据的交会预报分析

目前普遍使用TLE数据进行在轨物体的危险交会预报. TLE数据误差不仅会影响交会预报的准确性, 还是计算碰撞概率的必要参数, 因此, 只有准确估计TLE数据误差, 才能得到可信的碰撞概率数值. 本文采用两种方法, 即TLE数据自比和与高精度轨道预报数据相比较的方法, 计算TLE数据误差, 并分别利用TLE数据和高精度数据计算同一交会, 比较两种数据预报的交会结果差异. 结果表明, 采用TLE根数自比方法的计算误差偏小, 而使用精轨数据作为校准数据所得到的TLE误差更接近真实误差, 计算碰撞概率更为合理, 有利于减少虚警.     

Estimation of the Love and Shida numbers: h2, l2 using SLR data for the low satellites

In this paper we present results for the global elastic parameters: Love number h₂ and Shida number l₂ derived from the analysis of Satellite Laser Ranging (SLR) data. SLR data for the two low satellites STELLA (H = 800 km) and STARLETTE (H = 810 km) observed during 2.5 years from January 3, 2005 until July 1, 2007 with 18 globally distributed ground stations were analyzed. The analysis was done separately for the two satellites. We do a sequential analysis and study the stability and convergence of the estimates as a function of length of the data set used.     

Precision orbit determination performance for CryoSat-2

In this paper we discuss our efforts to perform precision orbit determination (POD) of CryoSat-2 which depends on Doppler and satellite laser ranging tracking data. A dynamic orbit model is set-up and the residuals between the model and the tracking data is evaluated. The average r.m.s. of the 10?s averaged Doppler tracking pass residuals is approximately 0.39?mm/s; and the average of the laser tracking pass residuals becomes 1.42?cm. There are a number of other tests to verify the quality of the orbit solution, we compare our computed orbits against three independent external trajectories provided by the CNES. The CNES products are part of the CryoSat-2 products distributed by ESA. The radial differences of our solution relative to the CNES precision orbits shows an average r.m.s. of 1.25?cm between Jun-2010 and Apr-2017. The SIRAL altimeter crossover difference statistics demonstrate that the quality of our orbit solution is comparable to that of the POE solution computed by the CNES. In this paper we will discuss three important changes in our POD activities that have brought the orbit performance to this level. The improvements concern the way we implement temporal gravity accelerations observed by GRACE; the implementation of ITRF2014 coordinates and velocities for the DORIS beacons and the SLR tracking sites. We also discuss an adjustment of the SLR retroreflector position within the satellite reference frame. An unexpected result is that we find a systematic difference between the median of the 10 s Doppler tracking residuals which displays a statistically significant pattern in the South Atlantic Anomaly (SSA) area where the median of the velocity residuals varies in the range of ?0.15 to +0.15?mm/s.     

A new approach to the telescope operation method for satellite tracking using a time synchronization technique

For the development of a telescope that is capable of precisely tracking satellites and high-speed operation such as satellite laser ranging, a special method of telescope operation is required. This study aims to propose a new telescope operation method and system configuration for the independent development of a mount and an operation system which includes the host computer. Considering that the tracking of a satellite is performed in real time, communication and synchronization between the two independent subsystems are important. Therefore, this study applied the concept of time synchronization, which is used in various fields of industry, to the communication between the command computer and the mount. In this case, communication delays do not need to be considered in general, and it is possible to cope with data loss. Above all, when the mount is replaced in the future, only the general communication interface needs to be modified, and thus, it is not limited by replacement in terms of the overall system management. The performance of the telescope operation method developed in this study was verified by applying the method to the first mobile SLR system in Korea. This study is significant in that it proposed a new operation method and system configuration, to which the concept of time synchronization was applied, for the observation system that requires an optical telescope.     

Time-varying solar radiation pressure on Ajisai in comparison with LAGEOS satellites

This study aims to investigate solar radiation pressure acting on the spherical geodetic satellites, Ajisai, LAGEOS-1, and LAGEOS-2. The solar radiation pressure coefficients ($C_R$) are derived in two independent ways: (a) through precise orbit determination (POD) using satellite laser ranging (SLR) data, and (b) through modeling using the optical properties of the satellite surface material. The average $C_R$ value of Ajisai (1.039), as calculated from the time series of $C_R$ POD estimates every 15?days, is consistently smaller than those of LAGEOS-1 (1.140) and LAGEOS-2 (1.103). This difference can be explained by the fact that the surface of Ajisai is mostly covered by mirrors. The Ajisai $C_R$ values estimated by POD show remarkable semi-annual variation, which disagrees with the results of a previous study (Sengoku et al., 1995) predicting that the $C_R$ of Ajisai varies almost annually. We attribute this semi-annual variation to two physical reasons: the non-spherical additional cross-sectional area due to the “attached fitting ring” and the low reflectivity of the surface material in the polar regions. Furthermore, the solar radiation pressure acting on Ajisai varies annually in a direction perpendicular to the sun-satellite vector. Finally, the two independent $C_R$ values of Ajisai agree more when we assume a total solar irradiance of 1361?W/m², whereas the value 1367?W/m² has been commonly used in POD.     

Photon counting detector for space debris laser tracking and lunar laser ranging

We are reporting on a design, construction and performance of solid state photon counting detector package which has been designed for laser tracking of space debris. The detector has been optimized for top photon detection efficiency and detection delay stability. The active area of the commercially available avalanche photodiode manufactured on Si (SAP500 supplied by Laser Components, Inc.) is circular with a diameter of 500 μm. The newly designed control circuit enables to operate the detection sensor at a broad range of biases 5–50 V above its breakdown voltage of 125 V. This permits to select a right trade-off between photon detection efficiency, timing resolution and dark count rate. The photon detection efficiency exceeds 70% at the wavelength of 532 nm. This is the highest photon detection efficiency ever reported for such a device. The timing properties of the detector have been investigated in detail. The timing resolution is better than 80 ps r.m.s, the detection delay is stable within units of picoseconds over several hours of operation. The detection delay stability in a sense of time deviation of 800 fs has been achieved. The temperature change of the detection delay is 0.5 ps/K. The detector has been tested as an echo signal detector in laser tracking of space debris at the satellite laser station in Graz, Austria. Its application in lunar laser ranging is under consideration by several laser stations.     

利用条件平差实现导航星座自主守时方法

针对导航星座自主导航系统的重要组成部分———自主守时系统,提出了一种简便易行的新算法:根据星间测距数据,采用条件平差进行自主守时计算;并且介绍了此方法基本原理和实现思路。自主守时仿真计算表明,此方法守时同步误差不累积,距离测量误差0.1m时,时间同步误差均方根小于0.4m。     

双向时间同步系统的设备时延校准技术研究

设备时延校准误差是卫星导航系统中伪码测距实现双向时间同步的重要误差因素,其精确校准是实现时间同步的关键技术。针对设备时延问题展开研究,提出了一种物理含义清晰、易于测量的设备时延的新定义。设计实现了一种双向时间同步系统的设备时延校准方案,基于时间同步站硬件平台验证了设备时延校准的有效性,试验结果表明时延校准的精度与准确度达到了亚纳秒量级。     

In-orbit assessment of laser retro-reflector efficiency onboard high orbiting satellites

The navigation and geodetic satellites that orbit the Earth at altitudes of approximately 20,000 km are tracked routinely by many of the Satellite Laser Ranging (SLR) stations of the International Laser Ranging Service (ILRS). In order to meet increasing demands on SLR stations for daytime and nighttime observations, any new mission needs to ensure a strong return signal so that the target is easily acquirable. The ILRS has therefore set a minimum effective cross-section of 100 million square metres for the on-board laser retro-reflector arrays (LRAs) and further recommends the use of ‘uncoated’ cubes in the arrays. Given the large number of GNSS satellites that are currently supported by SLR, it is informative to make an assessment of the relative efficiencies of the various LRAs employed. This paper uses the laser ranging observations themselves to deduce and then compare the efficiencies of the LRAs on the COMPASS-M1 navigation satellite, two satellites from the GPS and three from the GLONASS constellations, the two GIOVE test satellites from the upcoming Galileo constellation, the two Etalon geodetic spheres and the geosynchronous communications test satellite, ETS-8. All the LRAs on this set of satellites employ back-coated retro-reflector cubes, except those on the COMPASS-M1 and ETS-8 vehicles which are uncoated. A measure of return signal strength, and thus of LRA-efficiency, is calculated using the laser-range full-rate data archive from 2007 to 2010, scaled to remove the effects of variations in satellite range, atmospheric attenuation and retro-reflector target total surface area. Observations from five SLR stations are used in this study; they are Herstmonceux (UK), Yarragadee (Australia), Monument Peak and McDonald (USA) and Wettzell (Germany). Careful consideration is given to the treatment of the observations from each station in order to take account of local working practices and system upgrades. The results show that the uncoated retro-reflector cubes offer significant improvements in efficiency.     

Status of the T2L2/Jason2 Experiment

The T2L2 (Time Transfer by Laser Link) project, developed by CNES and OCA will permit the synchronization of remote ultra stable clocks and the determination of their performances over intercontinental distances. The principle of the experiment derives from Satellite Laser Ranging (SLR) technology with dedicated space equipment. T2L2 was accepted in 2005 to be on board the Jason2 altimetry satellite. The payload consists of both event timer and photo detection modules. The system uses the ultra-stable quartz oscillator of DORIS as on-board reference clock on one hand, and the Laser Reflector Array, making T2L2 a real two-way time transfer system on the other hand. The expected time stability of the T2L2 instrument (detection and timing), referenced by the DORIS oscillator and including all internal error sources should be at the level of 10–12 ps at 1 s and <1 ps at 1000 s. The metrological specifications of T2L2 should permit to maintain a precision of 1 to a few ps when measuring the phase of a clock during around 1000 seconds.     

半导体激光器干涉测距进展

全面评述了近年来半导体激光器应用于干涉测距的进展,对其中的代表性文献进行了详细的分析,指出了该技术今后的主要发展方向和关键问题。     

基于星光角距/激光测距的卫星组合导航方法

为了进一步提高卫星天文自主导航精度,提出了一种利用激光测距辅助的天文组合导航方法。激光测距能够直接获取卫星到地面参考信标的高精度距离信息,在以星光角距为观测量的天文导航系统中引入激光测距辅助数据,可以拓展滤波器观测量的维度,从而改善滤波效果。由于组合导航系统为非线性系统,为避免泰勒展开线性化引起的二阶截断误差,采用UKF滤波方法进行组合导航系统信息融合。仿真结果表明,所提出的组合导航方法能够明显提升导航精度,改善滤波性能。