基于CFD技术的高效叶栅耦合颤振分析方法

为了考虑叶轮机叶片结构与流体之间的耦合效应,同时提高叶轮机颤振数值研究的效率,发展了一种基于非定常气动力降阶模型(ROM)的叶栅耦合颤振分析方法。该方法运用时域计算流体力学(CFD)技术计算少数几个叶片的非定常气动力,通过系统辨识及一些假设构建整个叶栅振动的非定常气动力降阶模型,并在状态空间耦合叶栅结构动力学方程建立叶栅气动弹性方程,采用特征值和时域仿真分析该系统稳定性。运用该降阶耦合方法对STCF4(Standard Test Configuration 4)以及NASA Rotor67叶栅系统的稳定性进行了计算。通过与直接计算流体力学/计算结构动力学(CFD/CSD)耦合方法和非耦合方法计算结果的比较验证了该方法的准确性,且该降价耦合方法的计算效率相对于直接CFD/CSD耦合方法提高了1~2个量级,为叶轮机气动弹性参数研究、失谐研究以及多模态耦合计算等提供了便利。     

风扇/压气机叶型厚度对颤振特性的影响

采用计算流体力学与结构动力学相结合的方法,数值模拟了三维振荡叶栅非定常黏性流场;通过对叶片表面非定常气动力及其所做非定常气动功的计算分析,采用能量法对叶片颤振与否进行预估判断。针对三维直叶片和风扇转子叶片,通过调整叶片的相对厚度,研究了叶片厚度变化对风扇/压气机颤振特性的影响。此外,通过对振荡叶栅非定常流场结构的研究,发现了叶片吸力面气流分离与叶片振动之间的耦合关系。本文的研究在风扇/压气机设计中,可用于评估最大相对厚度等叶型结构设计参数对气弹稳定性的影响,对叶轮机颤振机理研究具有一定的参考意义。     

基于CFD/CSD耦合的叶轮机叶片失速颤振计算

为了研究叶轮机叶片的失速颤振特性,发展了一种计算流体力学与计算结构力学(CFD/CSD)时域耦合方法。该方法通过每一物理时刻CFD和CSD的循环迭代实现了耦合计算。在CFD分析中,采用鲁棒性较好的空间离散格式AUSM+-UP,并基于延迟脱体涡模型(DDES)模拟了带分离流动。在结构分析中,通过模态法构建了旋转叶片动力学方程并运用杂交多步方法进行求解。以孤立转子Rotor37为例,计算了不同工况下流场总体与细节参数,与实验结果的对比验证了CFD算法的精度。对某转子叶片进行了颤振特性研究,计算所得的广义位移时间响应曲线表明该叶片在近失速工况下会发生失速颤振,其表现形式为一阶弯曲模态发散且各阶模态之间不耦合。分析表明,流场不稳定和非定常效应是引起失速颤振的关键因素,同时折合频率的降低也会导致原本气动弹性稳定的叶片发生失速颤振。     

压气机转子叶片颤振边界的预测方法

通过发展的基于能量法的颤振数值预测方法得到了压气机转子叶片的颤振边界.将计算结构动力学(CSD)分析得到的叶片表面节点位移插值到耦合面的流体网格点上,并将设计的多层动网格技术应用于计算流体动力学(CFD)方法,实现叶栅振荡作用下的非定常分析,得到叶片表面的非定常气动功以及模态气动阻尼比.以某第一级压气机转子叶片为例,对...     

叶间相位角对叶片颤振的影响

发展了一种基于能量法并计及叶间相位角(IBPA)影响的数值计算方法.建立了全环振荡叶栅模型,将每一个扇区分为叶片表面附近的可动域及其外围的固定域,采用有限元形函数将计算结构动力学(CSD)网格点位移的传递到计算流体动力学(CFD)的耦合面网格点上,求解了全环振荡叶栅由k-ε湍流模型封闭的Reynolds平均Navier-Stokes(RANS)方程.以NASA 67转子叶片为例,在设计转速下,基于能量法分析了叶间相位角对叶片颤振的影响.计算结果表明:叶间相位角对叶片颤振有显著影响.      

基于系统辨识技术的叶轮机非定常气动力建模方法

 为了快速获得不同刚度的叶轮机叶片颤振特性,提出了一种基于系统辨识技术的叶片排非定常气动力建模方法,分析了叶片气动阻尼随叶间相角差和固有频率的变化特性.该方法通过对多叶片通道的某一叶片单独施加一个扫频振动信号,求解一次非定常流场,得到叶片排上每个叶片的气动力响应,通过系统辨识,获得每个叶片的气动力频率响应.根据小扰动流的叠加原理,得到扫频范围内各固有频率下的叶片排所有叶片共同激励的气动力模型,由此进一步得到各个不同固有频率的所有叶间相角差下的气动阻尼.针对STCF4(Standard Test Configuration 4)算例,该方法的计算结果与直接采用计算流体力学(CFD)方法和直接采用谐振信号的降阶方法(ROM)得到的气动阻尼系数吻合得很好.该方法只需进行一次非定常CFD计算就能得到扫频范围内不同固有频率下的气动阻尼特性曲线,极大地提高了计算效率,方便了叶轮机设计初期的气动弹性稳定性参数分析.     

压气机线性振荡叶栅气弹试验研究（二）：叶尖间隙的影响

 为了加强对叶轮机三维气动弹性机理的理解,为数值模拟方法提供试验验证数据,开展了压气机线性叶栅气动弹性试验研究。本研究分为2个部分,第1部分研究压气机线性振荡叶栅的气弹稳定性,本文为第2部分,重点辨别叶尖间隙对压气机叶片气弹稳定性的影响。试验结果表明随着叶尖间隙的增加,间隙流对振动叶片有失稳影响,其影响范围几乎遍及整个叶高,这与非定常气动的瞬时径向相互作用的结论是一致的。这种失稳效应与叶片间相位角对叶栅气弹稳定性的影响不耦合。间隙流在叶栅稳定性最差时影响最显著。详细的非定常压力试验结果表明,随着叶尖间隙的增加,叶片表面非定常压力幅值减小区域与间隙流造成的卸载区域相对应。由试验结果可以推断,不考虑叶尖间隙的数值模型可能会给出过稳定的叶片颤振预测。     

基于气/固耦合非定常流动的叶栅颤振分析

采用二维N-S方程／结构振动方程组耦合数值方法，分析计算了二维非定常气动力强迫振动条件下振动能量及气动力对叶栅所做的功，分别根据振动能量和气动力做功分析了叶栅的颤振特性。NACA0012和PROF叶栅在不同折合频率下气动参数随时间的变化表明，折合频率是影响叶栅颤振的重要因素。气固耦合方法得到的NA-CA0012叶栅颤振折合频率比非耦合的结果高，而对PROF叶栅则相反。这表明叶栅结构动力参数对其发生颤振时的折合频率影响很大且很复杂，要准确预测颤振应该考虑叶栅结构动力与气动力的耦合因素。     

二维叶栅气固耦合颤振分析

引入叶片结构动力学方程,通过数值求解气动/结构耦合方程体系,研究了气固耦合条件下叶栅内的二维非定常粘性流动,并初步进行了叶栅的颤振分析。针对两种叶型分别计算了不同折合频率下的流场,通过比较振动叶栅相关参数随时间变化的曲线,表明折合频率是决定叶片颤振与否的重要因素。      

航空发动机叶片颤振机理探究

航空燃气涡轮发动机中,由颤振引发的叶片疲劳失效是导致发动机机械故障的主要原因之一。为了研究叶片颤振这一非定常气动现象,在能量法的基础上采用弱耦合的计算方法,模拟了发动机风扇叶片在不同转速和不同出口反压条件下的振动,得到了叶片的颤振边界。其中流场与叶片建模用到三维线性插值法转化振动位移,流场动网格建模用到了多层动网格技术。计算表明,叶片表面气动功的分布与叶栅内的激波分布有很大的关系,激波在叶栅通道中的振荡是引起叶片颤振的原因之一。激波在叶栅中前后振荡,使得叶片表面上单位面积做正功的区域发生变化。做正功的区域扩大时,叶片表面气动功绝对值减小,从而气动阻尼比减小,更靠近颤振边界。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.