Capacities of mobile air/ground radio communication systemsemploying cylindrical cells

Cylindrical cells represent actual service volumes used in terminal areas (airports) for air traffic control (ATC) communications between pilots and ground controllers. The channel capacities of simplex and duplex frequency division multiplexing (FDM) mobile air/ground (A/G) radio communication systems employing cylindrical cells are compared assuming a network of identical cylindrical cells and a dedicated radio channel per group of aircraft and its ground controller. The two systems are compared considering both cochannel and adjacent channel interferences for analog and digital modulation. Then, capacities of duplex FDM and code division multiplexing (CDM) are compared under the same assumptions for digital modulation. The capacity of FDM depends mainly on the frequency reuse distance while the capacity of CDM is limited by the self users interference. This work shows that the capacity ratio of duplex and simplex FDM systems depends on the cell dimensions. It also shows that considering ATC requirements, FDM provides a higher capacity than CDM for all the cell dimension ranges considered     

星锁异常分析方法及处置策略

扩频模式星锁指示是判断上行信号锁定与否的重要参数,它是关系到双捕能否完成的关键.针对地面测控设备跟踪某遥感卫星时星锁异常的问题,采用FTA(故障树分析法)从星地两方面查找原因,找出了造成星锁异常的主要因素是扩频应答机下行测量帧中CRC(交叉冗余码校验)计算错误,诱因归结为扩频应答机FPGA(现场可编程门阵列)存储器中程...     

On the Perfomance of Air Traffic Control Radar Beacon System

The sidelobe suppression and improved sidelobe suppression mode performance of terminal and enroute air traffic control radar beacon systems using the existing antenna and a typical improved antenna in the presence of perfectly dielectric flat ground are investigated theoretically. Necessary analytical expressions for various quantities characterizing the system performance have been derived. A general purpose computer program has been developed for the computation and tabulation of these quantities as functions of the elevation angle of the observation point and for different combinations of heights of the directional and omnidirectional antennas of the beacon. Although the discussions given here apply to some specific antenna configurations, the theoretical method developed has more general application in evaluating quantitatively the performance of the beacon system in a given situation.     

月球探测器与地球轨道卫星测控通信干扰分析

对月球探测器的测控通信,通信距离遥远,信号空间损耗大,地面站接收机灵敏度高,因此更易受到外来信号干扰的影响。本文根据卫星网络间同频干扰计算方法,分析月球探测器测控通信下行链路受地球轨道卫星发射信号的干扰问题,主要包括月球探测器受地球静止轨道卫星（GEO）和地球非静止轨道卫星（NGSO）的干扰分析。在此基础上实现了仿真,计算其受干扰的可能性。     

一种卫星延时遥测分类处理和下传方法

延时遥测是掌握卫星在测控站不可观测弧段工作状态的重要手段,在深入分析卫星遥测参数特征的基础上,对卫星遥测参数按类型进行分类处理,提出了对各类延时遥测参数不同的处理、存储和下传方法;实现了下行遥测码速率受限情况下优化利用卫星存储资源和下行信道资源,使地面可准确掌握卫星在不可观测弧段的工作状态,尤其为不可观测弧段异常问题的判断和定位提供有效的遥测数据支持;实现了延时遥测数据的自主存储和下传,大大减轻了地面测控站的控制工作量.该延时遥测方法已成功应用于某卫星,取得了良好的应用效果.     

大型民用客机管制与监视系统验证及测试平台的构建

研发大型民用客机航路管制与监视系统验证及测试平台,从而实现机地数据通信系统环境下的航路管制与监视信息的数据地面接收和处理;同时,依照现有的空管航路管制与监视功能的国际标准和相关区域的运行要求,实现地面管制系统向机载系统的数据发布。该项研究成果能对口飞机机载数据链相关的ATC(Air Traffic Control,空中交通管制)功能和部分监视功能ADS-C(Automatic Dependent Surveillance-Contract,合同式自动相关监视)、ADS-B(Automatic Dependent Surveillance-Broadcast,广播式自动相关监视),提供对应的地面收发端,监控机载系统数据状态。     

地效翼风洞试验支架干扰数值分析

对地效翼移动地面风洞试验研究中的支架干扰进行了数值模拟和分析。分别对独立地效翼,带支架的地效翼及独立支架进行了数值模拟,计算采用可实现的κ-ε模型,通过求解定常不可压N-S方程,得出地效翼及支架周围流场分布情况。对几组计算结果比较分析了支架和地效翼的空气动力及由于干扰引起的空气动力,发现支架与地效翼之间的相互干扰随着地效翼迎角的增大而增强,如果忽略流动干扰造成的空气动力变化,地效翼升力误差很小,但阻力误差相对较大。同时对有干扰下和没有干扰下的流场进行了对比,分析了支架对翼尖涡流动及绕机翼流动的干扰。翼尖涡在地效翼翼尖附近的发展在0．5犮范围内基本不受支架的干扰;除支架对流场产生干扰外,移动带区域以外的固定地面附近粘性流动也对绕地效翼流动有一定的影响。本研究分析了风洞试验结果的可靠性,为地效翼风洞试验优化设计和地面效应风洞试验研究提供了参考。     

地面等待和改航策略的流量管理方法

恶劣天气下,过多的地面等待往往造成终端区的拥堵和航班的过分滞留,充分利用航路容量是解决这一问题的途径之一。结合地面延误程序和改航策略,建立了动态不确定性情况下航班起飞时刻和航路选择模型,基于当前的航班计划,通过迭代算法和Dijkstra算法,获得优化的起飞时刻和航路选择。仿真结果表明,结合改航策略后,可提高航路容量的利用率,航班的总体延误可在一定程度上减少。     

协方差分析描述函数法在终端航空武器投放动态仿真研究中的应用

 以终端航空武器系统空对地武器投入为例,研究和分析了协方差分析函数法在常规武器投放统计性能计算中的应用,建立了空－地武器投放数字仿真的均值方程和协方差方程,引入了弹着点传递矩阵,并与统计试验法比较了弹着点误差的统计特性。     

深空测控再生伪码测距技术研究

针对深空测控任务中低信噪比情况下的航天器高精度测距问题,对再生伪码测距技术进行论述。介绍再生伪码测距技术原理,再生伪码测距通过再生方式消除信号上行链路噪声,提高了信噪比,但需要复杂的相关器;分析再生伪码测距采用的陶思沃斯码结构,详细论述再生伪码测距信号的地面上行、星上再生、地面下行处理过程,重点介绍各处理过程中的指标条件,并对再生伪码测距进行误差分析;重点对比分析再生伪码测距与传统透明转发测距,指出前者适合于深空低信噪比条件下的高精度测距,后者适用于近地高信噪比条件下的测距。     

基于高级在轨系统的测控数传一体化方案

针对测控与数据传输信道一体化的需求,采用AOS(Advanced Orbiting System,高级在轨系统)空间链路层的等时业务,设计了一种测控数传信道一体化方案,可在上下行信道采用非相干信息帧同时传输测量信息及高速载荷数据.该方案设计了2种工作模式,模式一在上下行信道同时使用AOS传输帧,双向数据传输速率最高3 Mbit/s,测距精度优于2 m;模式二上行信道使用遥控扩频帧,可进行多站测距,抗多址干扰能力不低于15 dB,抗单频干扰能力不低于23 dB,下行信道使用AOS传输帧,最高数据传输速率3 Mbit/s,测距精度优于1 m.     

地球敏感器月球自主干扰保护异常分析及对策

针对某同步三轴稳定卫星地球敏感器自主干扰保护异常的问题,分析了地球敏感器受月球干扰的机理,详细比较了地面与星载月球干扰预报算法,挖掘比对了星载干扰保护软件数据,通过分析遥测数据及事后地面仿真计算软件处理验证,对异常点进行了准确定位,得出了星载月球干扰预报算法的局限性会导致卫星自主干扰保护异常的结论。并在此基础上,提出了在轨卫星地球敏感器受月球干扰自主保护异常时的处置对策,对后续同平台卫星相关设计提出了修改建议。     

Rotating Blades Radio Interference in a Helicopter-Borne CW Doppler Radar

Radio interference generated in a helicopter-borne continuous wave (CW) Doppler radar system due to the rotating blades is analyzed. This problem has been previously treated for the case of pulse Doppler radar systems with very narrow (near zero) beamwidth. In this case the strong interference component returning directly from the blades (with no ground reflection) need not be considered as it reaches the receiver when it is still blinded. In the case of a CW Doppler radar, however, this interference component must be included. Numerical calculations show that the total blade interference power level, dominated by the direct component, is higher than that of the direct ground clutter in the radar clutter region. It decreases approximately as (f - fo)-4 in the radar clear region. It stays, however, well above the thermal noise level which might cause false alarm and degrade the radar performance.     

基于时间推进的涡扇发动机整机通流数值模拟

为实现航空发动机整机流场与性能快速分析,基于准三维控制方程模型,开发了整机通流数值模拟程序。程序基于计算流体力学理论,并考虑了引气、冷却和喷油等发动机中的物理现象。为模拟叶片对气流偏转作用,推导了一种鲁棒的无粘叶片力模型,同时采用粘性力模型模拟粘性损失效应。采用该程序对某型双轴分排涡扇发动机一个地面试车工况点进行了整机数值仿真,并与实验数据进行了对比验证。结果表明,所发展程序求解稳定,能够自动捕捉激波,并且可以快速获得完全收敛的航空发动机整机准三维流场,单工况点计算时长不大于30min。其中计算截面平均参数与实验测量偏差不大于8%,符合工程应用精度需求。     

大型民用客机管制与监视系统验证与测试平台的构建

目的在于研发大型民用客机航路管制与监视系统验证与测试平台,以实现机地数据通信系统环境下的航路管制与监视信息的数据地面接收和处理;同时,依照现有的空管航路管制与监视功能的国际标准和相关区域的运行要求,实现地面管制系统向机载系统的数据发布。该项研究成果能对口飞机机载数据链相关的ATC(Air Traffic Control空中交通管制)功能和部分监视功能ADS-C(Automatic Dependent Surveillance-Contract合同式自动相关监视)、ADS-B(Automatic Dependent Surveillance-Broadcast广播式自动相关监视),提供对应的地面收发端,监控机载系统数据状态。该成果可以配合飞机研发过程中的试验和排故,并为适航验证工作提供有力的准备和支持。     

污染空气对超音速燃烧地面试验结果的影响

文中阐述了超燃冲压模型燃烧室地面试验时,进口空气污染的影响。从超燃燃烧室内的自动着火,燃烧过程机理来分析污染物(H_2O)的作用。用电弧加热进口气流及向气流喷水模拟氢加热器加热。结果表明:如果使用氢加热器直接加热空气,进口空气中含有污染物,它对超音速燃烧室地面试验的影响,将取决于进口气流状态,喷射方式、污染物含量和氢当量比等,是模拟试验中必须予以考虑的问题。     

Optimal trajectory and downlink power control for multi-type UAV aerial base stations

Unmanned Aerial Vehicles (UAVs) enabled Aerial Base Stations (UABSs) have been studied widely in future communications. However, there are a series of challenges such as interference management, trajectory design and resource allocation in the scenarios of multi-UAV networks. Besides, different performances among UABSs increase complexity and bring many challenges. In this paper, the joint downlink transmission power control and trajectory design problem in multi-type UABSs communication network is investigated. In order to satisfy the signal to interference plus noise power ratio of users, each UABS needs to adjust its position and transmission power. Based on the interactions among multiple communication links, a non-cooperative Mean-Field-Type Game (MFTG) is proposed to model the joint optimization problem. Then, a Nash equilibrium solution is solved by two steps: first, the users in the given area are clustered to get the initial deployment of the UABSs; second, the Mean-Field Q (MFQ)-learning algorithm is proposed to solve the discrete MFTG problem. Finally, the effectiveness of the approach is verified through the simulations, which simplifies the solution process and effectively reduces the energy consumption of each UABS.     

Terminal control monitor for ATC using knowledge-based system

A knowledge-based system for air traffic control (ATC) in terminal control regions is designed for improving service and operation. Domain knowledge is established following rules, regulations, and comments from controllers. An expert system is adopted for approach control and airport control in the terminal control region. The proposed system was implemented in PC-AT with Turbo Prolog. The air terminal control monitor was checked with regard to flight information input, real-time data refreshment, air traffic rescheduling, constraint violation double checking, emergency responses, and normal monitoring. Simulation results are given     

Satellite inclination effects on UHF Satcom operation

The cause, magnitude, and time variance of satellite inclination are examined in light of the effects on military UHF SATCOM operation. The effects on required demodulator acquisition range, earth coverage footprint, and user terminal antenna pointing accuracy are considered. It is shown that the allowable satellite inclination to maximize on-orbit lifetime is not based on earth-terminal antenna pointing accuracy, but on allowable loss of high-latitude satellite coverage area. Worst-case Doppler shift for a UHF military satellite is 85-Hz uplink and 67-Hz downlink for a 5° SATCOM user elevation angle and 10° of satellite inclination. This amount of inclination is a reasonable allowance for station-keeping, to minimize thruster fuel and thus maximize satellite life. It is also shown that uplink Doppler frequency shift due to satellite inclination may be corrected based on satellite ephemeris data and rough user terminal location data     

Backup radio site identification in air traffic control systems

The identification of backup radio sites, to increase the availability of the future air/ground (A/G) air traffic control (ATC) systems, is investigated, When there is an A/G communications failure, due to a radio site or an ATC controller access failure, another site (or sites) provides the service. The backup site should be capable of providing full coverage of the desired airspace known as the service volume. Meeting the full coverage conditions by one site or a group of sites is analyzed. It is concluded that identification of one site providing full coverage can be determined easily. The identification of a group of sites, each with partial coverage and providing full coverage is analyzed in detail. An algorithm involving both analytical and numerical approaches is described. It determines if two radio sites with given geographical coordinates, and each with partial coverage of a given cylindrical service volume, can provide full coverage. This algorithm can be implemented as a computer program to process a database of radio sites