Mean-Level Detection Utilizing a Digital First-Order Recursive Filter

The use of a simple digital first-order recursive filter for mean-level detection is described. Performance characteristics are derived for the case where the background noise is stationary, and detection results are given for Swerling Case 2 fluctuating signals. Equations are derived for computing false-alarm performance in nonstationary backgrounds, and results are given for some special cases. Comparisons are made with performance of a conventional mean-level circuit in stationary and nonstationary noise.     

An Adaptive Threshold System for Nonstationary Noise Backgrounds

The problem of detecting target signals in an ocean environment using active sonar is complicated by the nonstationary background which usually consists of both ambient ocean noise and reverberation. on. In this paper a signal processing system capable of detecting a signal in nonstationary noise is introduced. This system makes use of the mean and variance time functions of the nonstationary noise background in order to design estimation filters which will cope with the nonstationarity. Appropriate statistics of the noise and signal (tone burst) plus noise have been obtained and are used to determine the probabilities of false alarm and detection and the receiver operating characteristics.     

Detection Performance of a Mean-Level Threshold

The problem of detecting signals in nonstationary clutter is met by presenting a mean-level or adaptive threshold which adjusts to the changing background level. Such a threshold performs better than a fixed threshold that must be set for the highest amplitude clutter. However, the mean-level threshold does not perform as well for stationary noise as a fixed threshold set at the proper value. One measure of effectiveness of an adaptive threshold is its performance in stationary noise (compared to the optimum fixed threshold) for a specified speed of response. For the mean-level threshold, a simple mathematical solution is found for the detection probability when the noise is stationary and the signal scintillates rapidly. The performance is evaluated for a wide range of mean-level-threshold time constants and for several false-alarm probabilities. The results are presented graphically. As an example, the mean-level threshold suffers 3 dB in detectability (equivalent signal-to-noise ratio) in the presence of stationary noise as compared to the optimum fixed threshold for 50-percent probability of detection, false-alarm probability of 10-8, and an adjustment time of 15 times the signal duration.     

Adaptive Radar Detection in Doubly Nonstationary Autoregressive Doppler Spread Clutter

The problem of adaptive radar detection in clutter which is nonstationary both in slow and fast time is addressed. Nonstationarity within a coherent processing interval (CPI) often precludes target detection because of the masking induced by Doppler spreading of the clutter. Across range bins (i.e., fast time), nonstationarity severely limits the amount of training data available to estimate the noise covariance matrix required for adaptive detection. Such difficult clutter conditions are not uncommon in complex multipath propagation conditions where path lengths can change abruptly in dynamic scenarios. To mitigate nonstationary Doppler spread clutter, an approximation to the generalized likelihood ratio test (GLRT) detector is presented wherein the CPI from the hypothesized target range is used for both clutter estimation and target detection. To overcome the lack of training data, a modified time-varying autoregressive (TVAR) model is assumed for the clutter return. In particular, maximum likelihood (ML) estimates of the TVAR parameters, computed from a single snapshot of data, are used in a GLRT for detecting stationary targets in possibly abruptly nonstationary clutter. The GLRT is compared with three alternative methods including a conceptually simpler ad hoc approach based on extrapolation of quasi-stationary data segments. Detection performance is assessed using simulated targets in both synthetically-generated and real radar clutter. Results suggest the proposed GLRT with TVAR clutter modeling can provide between 5–8 dB improvement in signal-to-clutter plus noise ratio (SCNR) when compared with the conventional methods.     

Calculating Detection Probabilities for Adaptive Thresholds

In calculating detection probabiities for radar and sonar systems it is usually assumed that the threshold required to yield a certain probability of false alarm is known. This is often not the case for real systems and therefore the threshold must be estimated using some measure related to the test statistic. This paper presents a calculation technique that handles estimated (adaptive) thresholds in a general framework that can be applied easily to many detection problems. False alarm and detection probabilities are calculated from the characteristic function of the noise or signal plus noise variate and the characteristic function of the threshold estimate. To illustrate the method the detection performance of overlapped discrete Fourier transforms (DFTs) is calculated for a narrowband Gaussian target signal.     

A sampling-based approach to wideband interference cancellation

Classical adaptive array schemes which use only complex spatial weights are inherently narrowband and consequently perform poorly when attempting to suppress wideband interference. The common solution to this problem is the use of tapped delay line filters in each spatial channel to facilitate space-time adaptive processing (STAP). The higher performance provided by the STAP architecture comes at the cost of a considerable increase in complexity. This paper presents a simpler technique based on programmable time adjustable sampling (TAS) that provides a limited number of wideband degrees of freedom. Two TAS methods are introduced: TAS-sidelobe canceler (TAS-SLC) is based on the sidelobe canceler, while TAS-minimum variance beamformer (TAS-MVB) is derived from the minimum variance beamformer. TAS is implemented by adjusting the sampling instant at selected array channels. TAS-SLC consists of controlling the sampling in the main channel of the sidelobe canceler With TAS-MVB array complex weights are substituted with TAS time delays. The performance of TAS methods with wideband interference is compared to the conventional sidelobe canceler and minimum variance beamformers. It is shown that TAS-SLC provides better performance than the sidelobe canceler, while TAS-MVB outperforms the minimum variance beamformer     

Detection of Known Signals in Nonstationary Noise

The basic design of a nonlinear, time-invariant filter is postulated for detecting signal pulses of known shape imbedded in nonstationary noise. The noise is a sample function of a Gaussian random process whose statistics are approximately constant during the length of a signal pulse. The parameters of the filter are optimized to maximize the output signal-to-noise ratio (SNR). The resulting nonlinear filter has the interesting property of approximating the performance of an adaptive filter in that it weights each frequency band of each input pulse by a factor that depends on the instantaneous noise power spectrum present at that time. The SNR at the output of the nonlinear filter is compared to that at the output of a matched filter. The relative performance of the nonlinear system is good when the signal pulses have large time-bandwidth products and the instantaneous noise power spectrum is colored in the signal pass band.     

GPS信号FFT自适应抗干扰技术的FPGA工程实现

针对自适应抗干扰技术展开研究,提出了易于FPGA实现的FFT自适应窄带抗干扰技术.这种方法减小了数字信号处理部分的计算量,提高了系统处理的实时性,降低了系统的复杂程度.实验表明在有宽带干扰存在的情况下,使用所提出的方法可以自适应检测并剔除窄带干扰.与GPS接收机的对接测试表明,该技术能大大提高接收机的抗干扰能力.     

基于误码率准则的窄带干扰抑制算法性能分析

采用有效的窄带干扰抑制技术,可极大地改善扩频通信系统的性能.首先详细介绍了频域干扰抑制算法的基本思想,给出了算法实现的模块框图;其次具体分析了算法实现的关键技术：重叠加窗,背景噪声估计,干扰门限确定及干扰消除策略;最后以误码率作为干扰消除算法性能的评判标准,仿真分析了频域窄带干扰抑制技术中干扰强度、干扰频带宽度、干扰频率位置、干扰消除门限、陷幅值、加窗重叠度等因素对系统误码率的影响,为在不同条件下算法最佳参数的选取提供了依据.仿真结果表明：当干扰消除门限值取4aF,陷幅值取2σF～6σF,加窗重叠度为50％时,该算法可获得最佳抗干扰性能.     

A recursive multiple model approach to noise identification

Correct knowledge of noise statistics is essential for an estimator or controller to have reliable performance. In practice, however, the noise statistics are unknown or not known perfectly and thus need to be identified. Previous work on noise identification is limited to stationary noise and noise with slowly varying statistics only. An approach is presented here that is valid for nonstationary noise with rapidly or slowly varying statistics as well as stationary noise. This approach is based on the estimation with multiple hybrid system models. As one of the most cost-effective estimation schemes for hybrid system, the interacting multiple model (IMM) algorithm is used in this approach. The IMM algorithm has two desirable properties: it is recursive and has fixed computational requirements per cycle. The proposed approach is evaluated via a number of representative examples by both Monte Carlo simulations and a nonsimulation technique of performance prediction developed by the authors recently. The application of the proposed approach to failure detection is also illustrated     

A noncoherent adaptive detection technique

An adaptive detection technique suitable for both stationary and nonstationary noise environments based upon a generalized likelihood ratio test (GLRT) formulation is presented. The detector, which is statistically equivalent to a special form of the Wilks's lambda test, noncoherently combines the information contained in a pulse train of arbitrary length for decision-making purposes. The probability density function of the test under the noise only hypothesis is shown to be central χ². Under the signal plus noise hypothesis, an exact statistical characterization of the test cannot be obtained, and, therefore, a Chernoff bound is derived. Results in terms of the probability of detection versus signal-to-noise ratio (SNR) obtained from Monte Carlo simulation, the Chernoff bound, and the optimal matched filter case are examined. The performance of the noncoherent detector is shown to be a function of the covariance matrix estimate and the number of data samples     

基于Kalman滤波的高频CW电报信号自动识别

针对强噪声背景下高频CW电报信号检测算法性能严重下降、误码率较高的问题,文章提出一种基于卡尔曼滤波的高频CW电报信号同步检测识别算法。利用自同步法对CW电报信号实现位同步,进而利用卡尔曼滤波针对时变干扰噪声设置自适应阈值,对信号能量进行软判决,实现CW电报信号的自适应跟踪检测,提取有效信号进行识别。通过短波信道仿真软件和实际短波通信测试表明,该算法能够在强噪声背景下有效检测识别CW电报信号,且算法可由迭代实现。     

序贯结构的Sage-Husa自适应滤波及其应用

在分析已有的Sage-Husa自适应滤波算法的基础上,本文首先推导了两种量测噪声自适应估计方法的等价性。为充分利用组合系统中已知的部分量测噪声参数,提高滤波稳定性和精度,研究了基于序贯结构的Sage-Husa自适应滤波算法;当组合系统测量噪声参数均为已知时,为降低算法复杂度,提高Sage-Husa自适应滤波的鲁棒性,加入协方差匹配的方法对序贯结构的Sage-Husa自适应滤波算法进行改进;通过在序贯结构下采用相应的信息融合策略,充分利用组合系统的输出信息。将两种算法分别应用于MIMU/GPS/磁强计组合系统中,基于跑车实验的离线数据分析表明,第一种滤波算法的滤波稳定性较标准自适应算法在滤波稳定性上有明显提高;第二种改进的滤波算法既降低了算法复杂度,又提高了抗野值效果,有效保持了组合系统在干扰状态下的导航精度。     

自适应滤波技术的研究

应用常规卡尔曼滤波器(KF)要求知道系统精确的数学模型和系统噪声与量测噪声的统计特性,才能获得理想的滤波效果,否则可能产生发散现象。人们越来越倾向于利用自适应滤波(AKF)技术来解决发散的问题。针对AKF技术的研究现状,本文探讨一种结构简单、实时性较强、工程上比较实用的AKF算法。仿真结果表明,这种算法具有较强的自适应性,为一种实用而有效的滤波方法。     

Adaptive Rectification Filter for Detecting Small IR Targets

Clutter suppression is one of the most important subjects in the field of small target detection under infrared (IR) strong clutter background. While removing the clutter background, however, such methods may reverse the relative energy distribution of target and noise in the clutter suppressed image, and disturb the subsequent target segmentation and detection. This paper analyzes the causation of such problems, does research on the relationship between target energy characteristics and detection probability, and presents a novel filter of energy distribution adaptive rectification (EDARF). Based on the EDARF, an improved framework of dim small target detection is proposed to rectify the energy distribution in the clutter-suppressed images by conventional adaptive filters. The proposed EDARF's performance is estimated by experimental comparisons of three linear/nonlinear filters before and after using EDARF. Extensive experimental results show that the proposed EDARF improves efficiently the performance of detecting dim small targets against strong undulant cloud-cluttered backgrounds.     

Output Signal-to-Noise Ratio for Amplitude and Intensity Modulated Laser

General expressions are obtained for output SNR for both amplitude- and intensity-modulated lasers, where bandlimited Gaussian noise has been chosen as a modulating signal, and in the presence of background light. Two types of modulating signals are considered: the baseband and bandpass modulating signals. Detailed calculations are made for output SNR when an ideal narrowband optical filter is used. The dependence of output SNR on several parameters, such as the center frequency of the modulating signal, the effective average quantum rate, and input SNR, are discussed. In addition, the difference in performance between amplitude and intensity modulation is discussed. The detection characteristics of the homodyne system are also considered.     

Theory of Adaptive Radar

This paper reviews the principles of adaptive radar in which both the spatial (antenna pattern) and temporal (Doppler filter) responses of the system are controlled adaptively. An adaptive system senses the angular-Doppler distribution of the external noise field and adjusts a set of radar parameters for maximum signal-to-interference ratio and optimum detection performance. A gradient technique for control of the radar array/filter weights is described and shown to generate weights which asymptotically approach optimum values. Simulation results illustrate the convergence rate of adaptive systems and the performance improvement which can be achieved.     

A new adaptive Kalman filter for navigation systems of carrier-based aircraft

The features of carrier-based aircraft’s navigation systems during the approach and landing phases are investigated. A new adaptive Kalman filter with unknown state noise statistics is proposed to improve the accuracy of the INS/GNSS integrated navigation system. The adaptive filtering algorithm aims to estimate and adapt the unknown state noise covariance Q in high dynamic conditions, when the measurement noise covariance R is assumed to be known empirically in advance. The new adaptive Kalman ...     

Design and Performance of an Adaptive Kalman Receiver for Synchronous Data Transmission

A class of multilevel linear-modulation data-transmission systems, over unknown, slowly time-varying, and bandlimited channels is considered. It is shown how sequence estimation in the presence of Gaussian noise and intersymbol interference can be carried out by means of a discrete Kalman estimator. Moreover, the receiver can be provided with data-aided adaptive loops for performing channel identification, carrier recovery, and timing extraction. A computational method is presented to evaluate the average probability of error of the overall system in the presence of inter-symbol interference, additive noise, and phase-and sampling-synchronization errors. The method is based upon nonclassical one-and two-dimensional quadrature rules, which are outlined in the Appendix. As an example, numerical performance results related to a phase-shift-keying (PSK) system are given. The results are obtained by means of general-purpose and system-oriented computers.