低雷诺数下吹吸气射流对NACA0012翼型气动性能的影响

基于Favre过滤的大涡模拟方法,对雷诺数Re=10^4,迎角α=6°下的NACA0012翼型上表面吹吸气射流进行了数值模拟,从翼型周围流场流线图、速度场云图、上下表面压力系数曲线以及上表面边界层位移厚度等多角度地分析了射流位置以及速度变化对翼型气动性能的影响。结果表明:射流位置对翼型气动性能影响较大,且吸气射流要明显优于吹气射流。对于吸气射流,前缘吸气要明显优于中后缘吸气,可有效增升减阻,并减小翼型尾部流动分离,抑制翼型气动参数扰动,其最佳吸气位置随着速度的增大逐渐向下游移动;而吹气射流对翼型气动系数的作用效果较差,但中后缘的吹气射流可减小飞行过程中的气动扰动量,且吹气越大,效果越明显。     

低雷诺数下协同射流关键参数对翼型气动性能的影响

协同射流是一种高效的新型主动流动控制技术,至今缺乏关键参数对翼型气动性能影响规律的系统研究。通过引入螺旋桨激励盘模型,发展了一种新的协同射流翼型流动模拟方法,使得射流反作用力计算更符合实际。在低雷诺数条件下,以NACA6415为基准翼型开展了射流动量系数、开口尺寸和位置等关键参数对翼型气动性能的影响规律研究,并探讨了相应的物理机制。结果表明：大迎角分离流状态下,射流动量系数对翼型气动性能的影响规律比小迎角附着流状态更复杂;随着吹气口尺寸增加,气泵功率系数先减后增,有效升阻比先增后减;随着吸气口尺寸增加,气泵功率系数逐渐减小,有效升阻比先增加后趋于平稳;吹/吸气口位置对翼型气动性能和气泵功率系数的影响很小。     

低雷诺数下层流分离的等离子体控制

为有效控制层流分离特性,消除或减弱低雷诺数时小迎角下的升力非线性现象,改善翼型升力特性,并通过翼型的上表面转捩带与油流显示测量对等离子体激励控制机理进行阐述,对厚度为16%椭圆翼型低雷诺数下的气动特性进行了风洞试验研究。在此基础上,在上表面前缘10%弦长处布置激励器,通过压力分布测量观察等离子体激励对层流分离的影响。试验结果表明：当翼型上表面仅发生层流分离时,等离子体激励和转捩带的作用类似,可以有效延迟或者消除后缘层流分离,从而增加升力;当翼型上表面出现层流分离气泡并发生再附现象时,等离子体可以有效减小或者消除层流分离泡的范围,从而减小升力;通过控制层流分离,占空循环等离子体激励可以实现对低雷诺数小迎角下的升力的线性控制。     

翼型低雷诺数层流分离现象随雷诺数的演化特征

层流分离现象是翼型低雷诺数条件下出现的典型流场特征。层流分离流动中包含流动分离、转捩、再附等非定常流动结构,层流分离流动的形成与演化会对翼型气动特性产生恶化作用。采用大涡模拟（LES）方法对低雷诺数范围内不同雷诺数下的翼型层流分离流动开展精细数值模拟,研究了雷诺数对翼型气动特性的影响规律及作用机理。LES方法采用隐式亚格子模型,基于结构化拼接网格,对流项离散和时间推进方法分别采用AUSM⁺格式以及双时间步方法。验证算例计算结果表明数值模拟方法的正确性及可靠性,雷诺数对翼型气动特性具有显著影响。随雷诺数降低,时均分离泡外形增大、位置后移,平均阻力系数增大,特别是在较低雷诺数下,翼型升阻力系数随时间出现振荡现象。进一步研究表明,造成不同时均分离泡形态和气动特性的原因在于翼型上表面分离剪切层的失稳与转捩特征。随雷诺数降低,流动黏性增大,导致分离剪切层速度梯度减小,流动发生转捩及再附位置后移,直至翼型表面不再发生转捩和再附。     

低雷诺数翼型局部振动非定常气动特性

针对低雷诺数翼型特殊的气动特性,采用基于动网格的非定常数值模拟方法,研究翼型表面不同弦向位置的局部蒙皮以不同频率及振幅振动时对低雷诺数翼型气动特性及流场结构的影响,揭示蒙皮振动增升减阻的机理。研究表明,在低雷诺数条件下局部蒙皮振动可有效提高翼型气动特性,与刚性翼型相比蒙皮局部振动可使翼型升力系数提高,阻力系数降低,升阻比提高。振动位置对翼型气动特性及流场结构有显著的影响,振动表面位于翼型前缘附近或位于层流分离泡中心时可有效控制翼型层流分离,从而提高翼型气动特性。振动频率对翼型表面层流分离及转捩位置均有显著的影响,随着振动频率增加,翼型气动特性出现最优值。与刚性翼型相比,表面振动使翼型转捩位置略向上游移动,摩擦阻力增加,但振动使等效翼型相对厚度减小,压差阻力明显减小。在小幅振动范围内,随着振幅增加,流场非定常特性更加显著,翼型升阻比增加。     

不同雷诺数下翼型气动特性及层流分离现象演化

低雷诺数下空气黏性效应突出,翼型表面普遍存在层流分离现象,相比常规雷诺数情况气动特性显著恶化。采用带预处理的Roe方法求解非定常可压缩Navier-Stokes方程的数值模拟技术和低雷诺数低湍流度风洞油流显示试验技术,对FX63-137翼型不同雷诺数下气动特性和流动结构展开深入研究。通过风洞油流显示试验可以清晰获得低雷诺数层流分离流动的两道油流汇集线。数值模拟结果表明其分别为时均化主分离线和二次分离线,两种结果定性定量均吻合较好,证明了本文的研究方法有效可靠;雷诺数从500 000降至20 000,翼型气动特性和层流分离流动结构均发生显著的变化,伴随阻力系数剧增和升力系数剧降,时均化流动结构从附体至出现经典的长层流分离泡,并最终演化为后缘层流分离泡,相应的两种分离泡的非定常流动结构也存在显著差异;对于阻力系数和升力系数而言,存在不同的临界雷诺数,因为导致阻力系数剧增的机理在于经典长层流分离泡的产生使翼型压差阻力大增,而造成升力系数剧降的主要原因在于后缘层流分离泡使得等效翼型后部弯度减小;非定常结果显示正是由于翼型表面漩涡周期性的生成与脱落,才造成了低雷诺数下升力系数的周期性波动。翼型上表面主分离涡即将脱落时,流线在后缘附近再附,升力系数达到峰值;而当流体从下表面向上卷起二次分离涡时,尾部流线大尺度分离,升力系数降至谷值。     

边界层吹吸气对高负荷扩压叶栅性能的影响

采用边界层流动控制能够有效抑制扩压叶栅的流动分离。以某大弯折角低稠度扩压叶栅为研究对象,利用数值模拟手段研究了原型、叶片表面边界层单独吹气以及吹吸气相结合等边界层控制手段下的流场和叶栅性能变化情况。结果表明,无论是单独吹气还是吹吸气相结合的边界层控制方法,都能有效控制扩压叶栅中的边界层分离,从而较大幅度地增大叶栅负荷,并降低气动损失;计算表明,吹气和吸气的效果不尽相同,且吹吸气口位置及吹吸气流量对边界层的流动亦有较为明显的影响。其中采用1.7%的吹气流量,结合1.38%的吸气量,可以使静压增压比提高15%以上,而损失系数降低至原型的20%以内。     

低压涡轮叶栅流动分离主动控制实验研究

 实验研究了低雷诺数条件下射流式旋涡发生器(VGJs)控制的低压涡轮叶栅,实验在西北工业大学吹气式低速涡轮平面叶栅风洞中进行,进口雷诺数范围为19 000~260 000,自由流湍流度为1%。实验中对VGJs吹气比为0~8,53%Cx,63%Cx和72%Cx射流位置,0°,30°,60°和90°射流偏斜角度,25 000,50 000和100 000雷诺数状态下叶栅出口流场和表面静压进行了测量。研究发现,VGJs有效地控制了低雷诺数条件下叶栅吸力面的流动分离;VGJs需要一个最小有效吹气比,大于此吹气比时,VGJs效果基本上不变,高吹气比VGJs效果稍微减弱;VGJs射流偏斜角越大,控制效果越好,90°偏斜角效果最好;位置对VGJs效果影响很大,VGJs控制流动分离的最佳位置应该在分离点附近;随着雷诺数提高,VGJs效果减弱,更高的雷诺数,VGJs会增大叶片损失。     

吹气位置对高负荷扩压叶栅性能的影响

高负荷扩压叶栅边界层容易发生流动分离.采用吹吸气相结合的流动控制方法可以有效控制分离并且提高扩压叶栅的性能.影响吹吸气流动控制效果的因素有很多,包括吹吸气位置.吹吸气流量以及吹吸气槽宽度等.通过研究某一大弯折角低稠度扩压叶栅在不同位置处吹气的数值模拟.发现从3%至17%弦长不同位置处吹气均能有效控制叶栅中的边界层分离,提高叶栅总体性能;计算还表明在原型叶型吸力面产生激波处吹气可以达到最好的控制效果,叶栅总压损失系数可降至原型的12%以内.     

低雷诺数下机翼气动特性研究及控制

高空长航时无人飞行器(HALE UAV)由于飞行环境空气稀薄、雷诺数低导致其气动性能恶化,如何通过流动控制改善机翼低雷诺数气动性能受到越来越多的关注。在低速风洞中通过测力、测压和边界层测试等试验技术开展了NACA 633-421直机翼模型气动特性试验和流动控制研究。天平测力结果表明:随雷诺数降低(Re<1.4×10⁵)机翼气动特性迅速恶化;最大升力系数损失严重,失速迎角急剧降低;分析翼面压力分布结果显示,机翼表面产生层流分离泡(LSB),其长度变化、位置前移和最终发生破裂的发展过程是导致机翼低雷诺数气动性能恶化的主要原因。采用合成微射流(Micro-SJ)对翼面层流分离泡进行流动控制,失速迎角推迟了11°,机翼最大升力系数由0.59提升至1.10,最大升阻比增加了13.6%。合成微射流控制具有选频特性,驱动频率f=200~400 Hz的合成微射流控制效果最佳,更易促进分离剪切层提前转捩,形成湍流再附,使得层流分离泡长度缩短。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.