共查询到20条相似文献,搜索用时 61 毫秒
1.
涡轮冷却叶片参数化建模及多学科设计优化 总被引:5,自引:2,他引:3
建立了一个涉及结构、气动、传热、振动、强度和寿命等学科的涡轮冷却叶片多学科设计优化系统, 进行了单孔薄壁冷却叶片的多学科设计优化.提出了单孔薄壁冷却叶片的参数化造型方法, 叶片叶型采用5次多项式构造, 气动与传热为三维耦合分析;叶片体积平均温度与最高温度为优化目标, 强度、振动和寿命等学科相关参数为约束, 模拟退火与序列二次规划组合算法进行叶片参数空间寻优, 在保持冷却气体流量不变的条件下, 优化提高了冷却效果, 降低了叶片材料的性能要求. 相似文献
2.
汪光文 《民用飞机设计与研究》2011,(1):13-19,28
风扇转子气动优化设计是结合CFD、遗传算法和风扇特性的跨学科自动设计方法,这种设计较少依赖经验,能实现多目标和多设计参数组合的优化设计。先研究了四个关键技术:具有耗时少、计算较准确的叶片通道流场数值计算方法;具有良好寻优能力的数值最优化方法;三维叶片造型的参数化方法;以气动性能为目标的多目标函数构建方法。再将上述四个关键技术模块整合,构建简易的气动优化设计软件。三维叶片优化算例证明了该软件的设计能力,其设计结果较满意、设计效率较高、设计周期短。 相似文献
3.
为研究气冷涡轮叶片设计的特点,搭建了一个可以对采用气膜冷却的气冷涡轮叶片进行全三维优化的平台,该平台可在有冷气喷射的条件下对叶片进行多目标优化.优化平台中采用11参数法对叶片进行造型.针对该造型方法和优化设计的要求对优化变量的选取和优化策略以及优化目标的设定进行了一定的探讨,采用多岛遗传算法对优化问题进行寻优.采用该平台对某航空涡轮第一级静叶进行了优化.由于对不同目标进行了加权处理,所以随着优化目标侧重点的不同,优化方案的叶型呈现出不同特点,其气动效率和冷却效果均有所改善. 相似文献
4.
5.
基于风扇参数化设计和数值模拟程序,分析风扇各主要结构参数对其气动性能的影响,为进一步的优化设计提供了条件.采用并行计算流体力学(CFD)方法,基于组合优化策略(正交实验设计、响应面模型、遗传算法和混合整型算法)以多工作点流量系数平均值最大为目标函数对风扇进行多参数结构优化.8025型轴流风扇的优化结果比初步设计方案的性能提高14.5%. 相似文献
6.
7.
燃气透平叶型气动与传热的优化设计 总被引:2,自引:0,他引:2
建立了一个透平叶型气动与传热优化的两步模型.第1步采用解析多项式曲线构造叶片的参数化造型,基于CFD数值模拟,通过正交设计和敏感性分析,优选几何设计参数.第2步采用贝塞尔(Bezier)曲线参数化叶型型线,以总压损失和表面热流加权函数为优化目标,调整叶型型线,获得了气动性能与热负荷较优的叶型.设计案例的结果表明:增加安装角可以降低叶片压力面热负荷;增大叶片前缘直径可以降低前缘滞止点热负荷.调整叶型的表面曲率分布,有可能推迟吸力面的转捩,弱化叶片表面的传热.两步优化法计算量小,收敛性好,具有工程应用价值. 相似文献
8.
9.
10.
11.
An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade. 相似文献
12.
工程环境中,飞机气动力设计面临在多个目标和多种约束条件下寻找最优值,需在较短时限内完成设计优化,并保证最终方案可靠。基于高性能计算环境,采用现代计算流体力学(CFD)数值模拟技术和优化技术等构建了面向实际工程的飞行器气动多目标优化设计平台:采用基于非均匀有理B样条(NURBS)方法的自由曲面变形技术,实现对工程复杂气动外形的参数化表达;采用网格变形技术,实现优化过程中计算网格的自动更新;采用基于有限体积方法和多块结构网格的雷诺平均Navier-Stokes(RANS)方程并行解算器进行气动力求解;采用基于精英保留策略的非支配排序的多目标遗传算法(NSGA-II)进行多目标全局优化求解;采用非线性单纯形算法进行局部优化求解,优化过程中,通过人工调整优化种群,引入人工经验,构建"人在回路"的设计流程。以某翼型/机翼气动力优化设计为例对该平台技术进行验证:多目标优化设计可得到清晰的Pareto前沿解分布;优化后的翼型/机翼在满足各项约束的前提下,具备更高的综合气动性能。结果表明:所发展的气动多目标优化设计平台具有很好的工程适用性。 相似文献
13.
This paper describes the shape optimization of NASA rotor 37 and rotor and stator blades in a single-stage transonic axial compressor.Shape optimization of the blades operating at the design flow condition has been performed using the response surface method and three-dimensional Navier-Stokes analysis.Thin-layer approximation is introduced to the Navier-Stokes equations,and an explicit Runge-Kutta scheme is used to solve the governing equations.The three design variables,blade sweep,lean and skew,are introduced to optimize the three-dimensional stacking line of the blades.The objective function of the shape optimization is an adiabatic efficiency.Throughout the optimization of rotor and stator blades, optimal blade shape can be obtained.It is noted the increase of adiabatic efficiency by optimization of the blade shape with the stacking line in the single-stage transonic axial compressor is more effective in a rotor blade rather than a stator blade because of the large deformation of blade shape in the stator blade. 相似文献
14.
为了缩短涡轮气动设计的周期,进一步发掘涡轮叶型的改进潜力,搭建了多级涡轮的翘曲S1流面气动优化平台.该平台具有速度快,周期短的特点.在考虑冷气的前提下,对多级叶片进行多层并行优化,避免了单列优化后叶列间匹配差的缺点,同时克服了多层S1流面的气动效率此消彼长的缺陷.对某型两级高压涡轮进行了气动优化设计,优化后10%,50%,90%叶高的S1流面的考虑冷气的气动效率分别提高了0.569%,0.490%,0.405%;第1级和第2级考虑冷气的气动效率分别提高了0.18%,0.05%;涡轮整体气动效率提高了0.15%;优化效果明显.经过分析可知,优化有效减小第1级导叶的通道横向二次流损失和第1级动叶的激波损失,第2级的原始叶型设计较为合理.下端壁喷射冷气是降低S1流面优化有效性的重要原因. 相似文献
15.
为了设计低流动损失超声风扇叶型,研制出基于数值最优化超声叶型设计软件.以叶型主要几何参数为叶型设计参数,针对轴向进气第一级风扇转子采用给定轮缘功、损失最小为目标函数.设计的优化叶型后面大部分呈平直因此气流转角小、减速增压完全通过激波实现.沿弦向叶片厚度逐渐增加使叶栅通道呈收缩,总体上使流过叶栅超声气流得到减速增压.优化叶型所构成叶栅流场具有多道激波、流动损失低.设计结果表明设计方法的可行性,并可为超声风扇叶型设计提供新思路. 相似文献
16.
基于并行遗传算法压气机叶片自动优化设计 总被引:4,自引:3,他引:4
结合小生境法与算子自适应法对基本遗传算法进行改进,采用WinSock接口、多线程、CS体系结构,实现并行遗传算法.将并行遗传算法与NS方程流场计算方法、Hicks-Henne函数叶型参数化方法结合构成叶型自动优化设计软件,软件可用于叶型设计和对已有叶型的改进.在构造目标函数时,根据工作攻角范围,构造了考虑非设计点性能的目标函数.分别对进口马赫数为0.5和0.9左右的叶栅采用三台计算机进行并行气动优化设计,优化叶型设计点和非设点性能都明显好于原始叶型. 相似文献
17.
An aerodynamic design optimization platform(ADOP) has been developed.The numerical optimization method is based on genetic algorithm(GA),Pareto ranking and fitness sharing technique.The platform was used for design optimization of the stator of an advanced transonic stage to seek high adiabatic efficiency.The compressor stage efficiency is increased by 0.502% at optimal point and the stall margin is enlarged by nearly 1.0% at design rotating speed.The flow fields of the transonic stage were simulated with FINE/Turbo software package.The optimization result indicates that the optimization platform is effective in3Dnumerical design optimization problems. 相似文献
18.
《中国航空学报》2016,(6):1602-1617
This study describes an integrated framework in which basic aerospace engineering aspects (performance, aerodynamics, and structure) and practical aspects (configuration visualiza-tion and manufacturing) are coupled and considered in one fully automated design optimization of rotor blades. A number of codes are developed to robustly perform estimation of helicopter config-uration from sizing, performance analysis, trim analysis, to rotor blades configuration representa-tion. These codes are then integrated with a two-dimensional airfoil analysis tool to fully design rotor blades configuration including rotor planform and airfoil shape for optimal aerodynamics in both hover and forward flights. A modular structure design methodology is developed for real-istic composite rotor blades with a sophisticated cross-sectional geometry. A D-spar cross-sectional structure is chosen as a baseline. The framework is able to analyze all realistic inner configurations including thicknesses of D-spar, skin, web, number and ply angles of layers of each composite part, and materials. A number of codes and commercial software (ANSYS, Gridgen, VABS, PreVABS, etc.) are implemented to automate the structural analysis from aerodynamic data processing to sec-tional properties and stress analysis. An integrated model for manufacturing cost estimation of composite rotor blades developed at the Aerodynamic Analysis and Design Laboratory (AADL), Aerospace Information Engineering Department, Konkuk University is integrated into the framework to provide a rapid and dynamic feedback to configuration design. The integration of three modules has constructed a framework where the size of a helicopter, aerodynamic performance analysis, structure analysis, and manufacturing cost estimation could be quickly investigated. All aspects of a rotor blade including planform, airfoil shape, and inner structure are considered in a multidisciplinary design optimization without an exception of critical configuration. 相似文献
19.
20.
针对超声速翼型滑翔机的气动外形优化问题,提出了一种多岛遗传算法与模拟退火算法相结合的混合优化算法。首先,通过多岛遗传算法产生一个随机的初始种群,找到全局最优点附近区域的一个次优解;然后,将此次优解作为模拟退火算法的初值启动退火进程,缩小设计空间的范围,找到全局最优解。优化结果表明,所提混合算法可以有效地解决飞行器外形优化问题;在数量巨大的设计空间中,滑翔机的最优气动外形能够以较低的计算资源代价快速得到;双弧形翼型的气动特性较六边形翼型更有优势,叉形尾翼的静稳定性和控制效率高于十字形;优化后的外形极大地增加了滑翔机的滑翔距离。 相似文献