一种地基GNSS接收机差分码偏差估算方法

GNSS不同频点间的码伪距作差会引入信号的差分码偏差(DCB),包括GNSS卫星及地面接收机的DCB.本文提出一种地基GNSS接收机差分码偏差参数估算方法,首先由电离层文件参数作线性插值,计算出电离层延迟误差.之后对IGS站观测文件进行加权最小二乘法估计,得到GPS卫星和地面GNSS接收机的L1C频点和L2P频点间码偏...     

基于三频数据的北斗卫星导航系统DCB参数精度评估方法

差分码偏差（Differential Code Biases,DCB）参数作为导航电文中重要的一项,是影响用户PNT服务的主要误差源之一。北斗卫星导航系统（后文简称“北斗系统”）发射三个频点的导航信号,在导航电文中需要发播卫星的2个TGD（Timing Group Delay）参数。文章首先介绍了北斗系统卫星DCB参数最小二乘解算与形式误差评估;其次根据北斗系统三频特点,提出了不同频点组合计算垂直方向电离层电子总含量（VTEC）互差的DCB精度定量评估方法,并与IGS(International GNSS Service)提供的GPS卫星DCB精度进行比较;最后,详细分析了DCB参数精度对用户等效距离误差（UERE）计算和定位计算的影响,分别采用卫星出场标定DCB参数和经过解算DCB参数进行评估。实测数据分析结果表明,北斗系统卫星DCB参数解算形式误差与IGS解算GPS卫星DCB参数形式误差相当,但受卫星类型和解算测站的几何分布限制,北斗系统卫星DCB参数解算不确定度相比IGS略差,估计精度优于0.5ns,不同频率组合计算VTEC互差绝对值均值优于0.6TECU。相比采用卫星出场标定值,采用系统解算DCB参数后,双频用户三维位置误差改善13.80%～47.42%。     

地基单站GNSS的电离层VTEC高精度解算方法

利用IGS提供的双频GNSS观测数据,分析了Kalman方法解算电离层垂直总电子含量(Vertical Total Electron Content,VTEC)存在的问题,提出了Kriging-Kalman改进解算方法,并对两种方法解算的电离层VTEC进行分析和比较.结果 表明:在低纬地区,当观测卫星数量发生改变时,K...     

MGEX北斗差分码偏差两种精确处理方法对比分析

差分码偏差是北斗卫星导航系统（BDS）在高精度定位和电离层建模中需精确处理的系统误差之一.利用MGEX发布的2017年全年和2018年6月的BDS卫星的差分码偏差数据,比较分析了DLR和CAS分别解算的BDS卫星差分码偏差的日解值、月平均值和稳定性的变化特性.分析结果表明,DLR与CAS估算的BDS卫星差分码偏差值差异不大,具有较好的一致性;2017年CAS估算的BDS卫星C2I-C6I差分码偏差稳定性略优于DLR,C2I-C7I差分码偏差稳定性与DLR相当,且均具有较高稳定性;2018年6月DLR C2I-C6I差分码偏差月平均值稳定性优于CAS;C2I-C7I差分码偏差的稳定性明显优于C2I-C6I差分码偏差,卫星差分码偏差月平均值稳定性优于日解值稳定性.      

基于硬件信号模拟器的电离层TEC监测仪差分码偏差长期变化

利用硬件信号模拟器可以标定电离层TEC监测仪的差分码偏差.通过对相同接收机时隔近41.5月进行的两次差分码偏差标定实验,以GPS系统为例分析了硬件标定法得到的差分码偏差随时间的长期变化情况.结果 表明:接收机差分码偏差均值从第一次实验的16.122 ns增加至第二次实验的16.749 ns,在约41.5月的时间内增加约...     

基于双频GPS观测的电离层TEC与硬件延迟反演方法

利用全球定位系统（Global Positioning System,GPS）的双频观测数据反演得到电离层的总电子含量（Total Electron Content,TEC）,使得广域甚至全球范围高时空分辨率的电离层观测研究成为可能,但由于GPS卫星和接收机对信号的硬件延迟可导致TEC测量系统偏差,因此,需要探索反演TEC并估测GPS卫星与接收机硬件延迟的有效算法.本文根据电离层电波传播理论,阐述了基于双频GPS观测提取电离层TEC的方法,给出TEC与硬件延迟的基本关系.综合研究了TEC与硬件延迟的反演方法,进行分析与归纳分类,在此基础上提出了有待深入研究的问题.      

单接收机GNSS数据组合硬件延迟的联合求解方法

利用GNSS观测数据解算TEC的最大误差源是硬件延迟,包括卫星硬件延迟和接收机硬件延迟.在单接收机情况下,由于数据稀疏以及接收到的卫星信号时间不对齐等特点,已有的解算硬件延迟方法的求解结果往往不理想.在应用局域模式拟合方法和SCORE方法求解单接收机数据基础上,利用局域模型拟合法在电离层平静期拟合较准确的优点,提出一种联合改进方法,同时改正了SCORE方法解算过程中约束过强的缺点.通过利用GPStation-6接收机的GPS和BDS实际观测数据进行解算分析,验证了所提方法的有效性与准确性.      

基于BDS/GPS和经验模型的区域电离层建模

基于北斗卫星导航系统（BDS）和全球定位系统（GPS）实测电离层穿刺点（IPP）数据,结合国际参考电离层（IRI）经验模型历史数据,提出一种对区域二维电离层总电子含量（TEC）进行高精度建模的方法.针对缺乏穿刺点的区域内短时间电离层建模时精度较低且各时段穿刺点空间分布不同的问题,该方法使用IRI模型在建模区域内均匀添加虚拟穿刺点数据,并根据与实测穿刺点的距离,使用构造的权重计算公式赋予其动态权重值,通过加权最小二乘法进行球谐模型参数解算.与欧洲定轨中心（CODE）发布的全球电离层图（GIM）进行数据比对发现,相对于只使用BDS/GPS实测穿刺点数据的建模方法,利用本文建模方法计算获得的垂直总电子含量（VTEC）值对缺乏实测穿刺点的区域精度有明显的提升.      

利用北斗观测数据实时监测中国区域电离层变化

北斗卫星导航信号采用三个频点工作,可以利用伪距双频组差方法解算电离层电子含量,为实时监视中国区域电离层变化提供新的技术手段.中国中低纬度处于电离层赤道异常变化区,在北纬20°±5°区域时常发生较大梯度的电离层变化.利用北斗实时多频伪距和相位观测数据,采用相位平滑伪距方法计算电离层穿刺点电子含量,分析通过北斗系统GEO卫星监测的电离层周日变化特性;采用多面函数方法拟合中国区域1°×1°分辨率的电离层延迟量,每5min绘制一幅中国区域电离层图,观测区域所有电离层穿刺点拟合残差RMS为2.778TECU;分析北斗系统实时监测中国区域电离层异常情况,当发生电离层异常变化时,相邻两天的VTEC（Vertical Total Electronic Content）峰值相差约60TECU.      

电离层周日变化对解算GPS硬件延迟稳定性的影响

针对电离层周日变化特征分析了其可能对SCORE方法估算的硬件延迟稳定性的影响. 利用BJFS以及XIAM台站的GPS观测数据, 解算了位于太阳活动高年(2001年)和太阳活动低年(2009年)的卫星硬件延迟并分析了估算的硬件延迟的稳定性. 研究发现, 电离层周日变化对估算的硬件延迟稳定性具有一定影响, 但是利用不同台站所得到的卫星硬件延迟稳定性在昼夜不同时间上的解算结果存在一定差异. 电离层周日变化对利用 BJFS台站数据解算的硬件延迟稳定性日夜差异较为明显, 在太阳活动高年利用XIAM 台站数据解算的硬件延迟日夜稳定性差异不很明显, 由于XIAM台站处于电离层赤道异常峰附近, 夜间电离层变化很大, 因此对比中纬度地区, 电离层周日变化对赤道异常峰附近地区硬件延迟稳定性解算结果的影响相对较小, 但在太阳活动低年, 其影响仍较为显著.      

SHAKING: Adjusted spherical harmonics adding KrigING method for near real-time ionospheric modeling with multi-GNSS observations

Precise positioning based on Global Navigation Satellite System (GNSS) technique requires high accuracy ionospheric total electron content (TEC) correction models to account for the ionospheric path delay errors. We present an adjusted Spherical Harmonics Adding KrigING method (SHAKING) approach for regional ionospheric vertical TEC (VTEC) modeling in real time. In the proposed SHAKING method, the VTEC information over the sparse observation data area is extrapolated by the Adjusted Spherical Harmonic (ASH) function, and the boundary distortion in regional VTEC modeling is corrected by the stochastic VTEC estimated using Kriging interpolation. Using real-time GPS, GLONASS and BDS-2/3 data streams of the Crust Movement Observation Network of China (CMONOC), the SHAKING-based regional ionospheric VTEC maps are re-constructed over China and its boundary regions. Compared to GNSS VTECs derived from the independent stations, the quality of SHAKING solution improves by 13–31% and 6–33% with respect to the ASH-only solution during high and low geomagnetic periods, respectively. Compared to the inverse distance weighting (IDW) generated result, significant quality improved of SHAKING-based VTEC maps is also observed, especially over the edge areas with an improvement of 60–80%. Overall, the proposed SHAKING method exhibits notable advantage over the existing regional VTEC modeling techniques, which can be used for regional TEC modeling and associated high-precision positioning applications.     

利用COSMIC数据构建的全球垂直TEC图的验证研究

在日固坐标系(地磁纬度和地方时)下, 累积地方时过去24h的COSMIC(Constellation Observing System for Meteorology Ionosphere andClimate)观测资料, 通过对110$sim$750km高度范围内的电子密度进行数值积分得到各掩星点的垂直TEC值, 进而利用Kriging方法插值产生近实时的全球地方时MAGLat2.5°×2h的COSMIC TEC图. 利用2008年1月1日至2010年6月30日共30个月的COSMIC数据, 逐日构建COSMICTEC图, 将其与全球导航卫星系统服务组织(International GNSS Service,IGS)发布的全球电离层TEC图(Global Ionospheric Maps, GIMs)以及OSTM/JASON-2卫星高度计观测值分别进行比对,证明利用COSMIC掩星资料构建全球电离层垂直TEC图是可行的.      

Negative VTEC with spherical harmonic expansion model under different solar activity conditions

The Earth’s ionosphere can be described by a spherical harmonic (SH) expansion up to a specific degree. However, there exist negative vertical total electron content (VTEC) values in the global ionosphere map (GIM) with the SH expansion model. In this contribution, we specifically investigated the negative VTEC values that are induced by the SH expansion model and validated the performance of the inequality-constrained least squares (ICLS) method in eliminating the negative VTEC values. The GPS data from 2004 to 2017 was selected to cover one solar cycle and the experiments under different solar activity conditions were analyzed. The results in our work show that the occurrence of the negative VTEC values is attributed to the deficiency of the SH expansion model when the VTEC itself is small instead of the unevenly distribution of the GNSS stations. The negative VTEC values appear periodically in the temporal domain, showing apparently one year and half year periods. During one year, two peaks in June and December can be observed in the time series of the negative VTEC values. The number of negative VTEC values in June is obvious larger than that in December. During one solar cycle, the number of negative VTEC values under quiet solar activity condition is obvious larger than that under strong solar activity condition. In the spatial domain, the appearance of the negative VTEC values is strongly related with the movement of the subsolar point. In the latitude of the subsolar point has the largest magnitude, the negative values will appear on the opposite hemisphere and the further from the subsolar point the more negative values. The maximum number of the negative VTEC values in the southern hemisphere appears in June, while the peak value in the northern hemisphere appears in December. The maximum number of negative VTEC values in the southern hemisphere is generally larger than that in the northern hemisphere. In addition, the negative VTEC values are distributed both at middle latitude and high latitude in the southern hemisphere, while they are mainly distributed at high latitude in the northern hemisphere. When the ICLS method is used, the negative VTEC values can be eliminated efficiently and it has nearly no influence on the positive VTEC values. The ICLS method can also improve the receiver’s differential code bias (DCB) and significantly decrease the unreasonable negative slant TEC (STEC) values along the lines of sight. Using the final GIM product of the Jet Propulsion Laboratory (JPLG) as a reference, the root mean square (RMS) of the ICLS solution shows maximum 25%, 20% and 45% improvement relative to the least squares (LS) solution at northern high latitude, southern middle latitude and southern high latitude, respectively.     

A MARS-based method for estimating regional 2-D ionospheric VTEC and receiver differential code bias

The geometry-free linear combination of dual-frequency GNSS reference station ground observations are currently used to build the Vertical Total Electron Content (VTEC) model of the ionosphere. As it is known, besides ionospheric delays, there are differential code bias (DCB) of satellite (SDCB) and receiver (RDCB) in the geometry-free observation equation. The SDCB can be obtained using the International GNSS Service (IGS) analysis centers, but the RDCB for regional and local network receivers are not provided. Therefore, estimating the RDCB and VTEC model accurately and simultaneously is a critical factor investigated by researchers. This study uses Multivariate Adaptive Regression Splines (MARS) to estimate the VTEC approximate model and then substitutes this model in the observation equation to form the normal equation. The least squares method is used to solve the RDCB and VTEC model together. The research findings show that this method has good modeling effectiveness and the estimated RDCB has good reliability. The estimated VTEC model applied to GPS single-frequency precise point positioning has better positioning accuracy in comparison to the IGS global ionosphere map (GIM).     

Wavelet modelling in support of IRI

The slant total electron content (STEC) of the ionosphere is defined as the integral of the electron density along the ray-path of the signal between the transmitter and the receiver. So-called geometry free GPS measurements provide information on the electron density, which is basically a four-dimensional function depending on spatial position and time. Since ground-based measurements are not very sensitive to the vertical structure within the atmosphere, the ionosphere is often represented by a spherical layer, where all electrons are concentrated. Then the STEC is transformed into the vertical total electron content (VTEC), which is a three-dimensional function depending on longitude, latitude and time.In our approach, we decompose an ionospheric function, i.e. the electron density or the VTEC, into a reference part computed from a given model like the International Reference Ionosphere (IRI) and an unknown correction term expanded in a multi-dimensional series in terms of localizing base functions. The corresponding series coefficients are calculable from GPS measurements applying parameter estimation procedures. Since the GPS receivers are located rather unbalanced, finer structures are modelable just in regions with a sufficient number of observation sites. Due to the localizing feature of B-spline functions we apply a tensor product spline expansion to model the correction term regionally. Furthermore, the multi-resolution representation derived from wavelet analysis allows monitoring the ionosphere at different resolutions levels. We demonstrate the advantages of this procedure by representing a simulated VTEC data set over South America.     

A method of estimating GPS instrumental biases with a convolution algorithm

This paper presents a method of deriving the instrumental differential code biases (DCBs) of GPS satellites and dual frequency receivers. Considering that the total electron content (TEC) varies smoothly over a small area, one ionospheric pierce point (IPP) and four more nearby IPPs were selected to build an equation with a convolution algorithm. In addition, unknown DCB parameters were arranged into a set of equations with GPS observations in a day unit by assuming that DCBs do not vary within a day. Then, the DCBs of satellites and receivers were determined by solving the equation set with the least-squares fitting technique. The performance of this method is examined by applying it to 361?days in 2014 using the observation data from 1311 GPS Earth Observation Network (GEONET) receivers. The result was crosswise-compared with the DCB estimated by the mesh method and the IONEX products from the Center for Orbit Determination in Europe (CODE). The DCB values derived by this method agree with those of the mesh method and the CODE products, with biases of 0.091?ns and 0.321?ns, respectively. The convolution method's accuracy and stability were quite good and showed improvements over the mesh method.     

Improved predictions of equatorial TEC for real time applications

It is important to use models developed specifically for the equatorial ionospheric estimation for real-time applications, particularly in Satellite Navigation. This work demonstrates a methodology for improved predictions of VTEC in real time using the model developed for the equatorial ionosphere by the authors. This work has been done using TEC data of the low solar activity period of 2005 obtained using dual frequency GPS receivers installed under the GAGAN project of ISRO. For the purpose, the model is first used in conjunction with Kriging technique. Improvement in accuracy is observed when compared with the estimations from the model alone using the measurements as true reference. Further improvement is obtained by Bayesian combination of these estimates with independent Neural Network based predictions. Statistical performance of improvement is provided. An improvement of ∼1 m in confidence level of estimation of VTEC is obtained.     

Estimation of differential code biases with Jason-2/3 onboard GPS observations

With the continuous deployment of Low Earth Orbit (LEO) satellites, the estimation of differential code biases (DCBs) based on GNSS observations from LEO has gained increasing attention. Previous studies on LEO-based DCB estimation are usually using the spherical symmetry ionosphere assumption (SSIA), in which a uniform electron density is assumed in a thick shell. In this study, we propose an approach (named the SHLEO method) to simultaneously estimate the satellite and LEO onboard receiver DCBs by modeling the distribution of the global plasmaspheric total electron content (PTEC) above the satellite orbit with a spherical harmonic (SH) function. Compared to the commonly used SSIA method, the SHLEO model improves the GPS satellite DCB estimation accuracy by 13.46% and the stability by 22.34%, respectively. Compared to the GPS satellite DCBs estimated based on the Jason-3-only observations, the accuracy and monthly stability of the satellite DCBs can be improved by 14.42% and 26.8% when both Jason-2 and Jason-3 onboard observations are jointly processed. Compared with the Jason-2 solutions, the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations have an improved consistency of better than 18.26% and 9.71% with the products provided by the Center for Orbit Determination in Europe (CODE) and Chinese Academy of Sciences (CAS). Taking the DCB products provided by the German Aerospace Center (DLR) as references, there is no improvement in accuracy of the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations than the Jason-2 solutions alone. A periodic variation is found in the time series of both the Jason-3 and Jason-2 onboard receiver DCB estimates. Preliminary analysis of the PTEC distribution based on the estimated SH coefficients are also presented.